TIM-1.0 WTMI-armada-17.10.3-d61ed3a WTMI: system early-init DDR topology parameters: ======================== ddr type DDR3 ddr speedbin 12 bus width 16-bits cs num 2 cs[0] - group num 0 cs[0] - bank num 8 cs[0] - capacity 512MiB cs[1] - group num 0 cs[1] - bank num 8 cs[1] - capacity 512MiB DRAM windows: ============= WIN[0] - base addr 0x60000000 WIN[0] - size 0x40000000 WIN[1] - base addr 0xa0000000 WIN[1] - size 0x20000000 memory test region: =================== CS[0] 0x60000000 - 0x7fffffff CS[1] 0x80000000 - 0x9fffffff Fill memory before self refresh...done Fill memory before self refresh...done Now in Self-refresh Mode Restore termination values to original values Exited self-refresh ... Self refresh Pass. DDR self test mode test done!! Self refresh Pass. DDR self test mode test done!! QS GATING ============= Calibration done: cycle = 0x00 tap =0x5F CH0_PHY_RL_Control_CS0_B0[0xC0001180]: 0x0000005F CH0_PHY_RL_Control_CS0_B1[0xC0001184]: 0x0000005F QS GATING ============= Calibration done: cycle = 0x00 tap =0x5C CH0_PHY_RL_Control_CS1_B0[0xC00011A4]: 0x0000005C CH0_PHY_RL_Control_CS1_B1[0xC00011A8]: 0x0000005C DLL TUNING ============== DLL 0xc0001050[21:16]: [0,2f,17] DLL 0xc0001050[29:24]: [4,32,1b] DLL 0xc0001054[21:16]: [0,2c,16] DLL 0xc0001054[29:24]: [9,34,1e] DLL 0xc0001074[21:16]: [0,3f,1f] DLL 0xc0001074NOTICE: Booting Trusted Firmware NOTICE: BL1: v1.3(debug):armada-17.10.7:16571d2 NOTICE: BL1: Built : 15:51:32, Apr 19 2NOTICE: BL2: v1.3(debug):armada-17.10.7:16571d2 NOTICE: BL2: Built : 15:51:34, Apr 19 2018NOTICE: BL31: v1.3(debug):armada-17.10.7:16571d2 NOTICE: BL31: U-Boot 2017.03-armada-17.10.1 (Dec 29 2018 - 11:26:46 +0800) Model: Marvell Armada 3720 ECK Board CPU @ 1000 [MHz] L2 @ 800 [MHz] TClock @ 200 [MHz] DDR @ 800 [MHz] DRAM: 1 GiB U-Boot DT blob at : 000000003f71b328 Comphy-0: USB3 5 Gbps Comphy-1: PEX0 2.5 Gbps Comphy-2: SATA0 6 Gbps MMC: sdhci@d8000: 0 SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB *** Warning - bad CRC, using default environment Net: SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB Factory mac is : B0-A7-B9-8E-EC-F1 eth0: neta@30000 [PRIME] Attach switch ID 0x004dd043 Attach switch driver for AR8236 Checking for firmware recovery mode... Reset button not pushed, do nothing Press CTRL+B to abort autoboot in 1 seconds switch to partitions #0, OK mmc0(part 0) is current device MMC read: dev # 0, block # 896, count 128 ... 128 blocks read: OK switch to partitions #0, OK mmc0(part 0) is current device MMC read: dev # 0, block # 1024, count 32768 ... 32768 blocks read: OK ## Flattened Device Tree blob at 04f00000 Booting using the fdt blob at 0x4f00000 Using Device Tree in place at 0000000004f00000, end 0000000004f05d3b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.109 (aholmes@astraea-lnx) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19336-374f325afbf) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Mar 31 01:54:14 2022 [ 0.000000] Machine model: Marvell Armada 3720 ECK Board [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '') [ 0.000000] printk: bootconsole [ar3700_uart0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] node 0: [mem 0x0000000004000000-0x00000000041fffff] [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 16 pages/cpu s28248 r8192 d29096 u65536 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048 [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000 mtdparts=spi0.0:1M(nor-flash) root=/dev/mmcblk0p1 rw rootwait [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1014196K/1048576K available (8256K kernel code, 878K rwdata, 2068K rodata, 512K init, 284K bss, 34380K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 192 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000 [ 0.000000] random: get_random_bytes called from start_kernel+0x3a8/0x57c with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns [ 0.008364] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000) [ 0.018957] pid_max: default: 32768 minimum: 301 [ 0.023815] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.031365] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.040701] rcu: Hierarchical SRCU implementation. [ 0.045721] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.053638] EFI services will not be available. [ 0.058385] smp: Bringing up secondary CPUs ... [ 0.063335] Detected VIPT I-cache on CPU1 [ 0.063370] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000 [ 0.063414] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.063507] smp: Brought up 1 node, 2 CPUs [ 0.085565] SMP: Total of 2 processors activated. [ 0.090398] CPU features: detected: 32-bit EL0 Support [ 0.095690] CPU features: detected: CRC32 instructions [ 0.101015] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.109581] CPU: All CPU(s) started at EL2 [ 0.113792] alternatives: patching kernel code [ 0.121101] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.131190] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.138265] pinctrl core: initialized pinctrl subsystem [ 0.144101] DMI not present or invalid. [ 0.148454] NET: Registered protocol family 16 [ 0.153383] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.160628] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.168567] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.177063] thermal_sys: Registered thermal governor 'step_wise' [ 0.177599] cpuidle: using governor ladder [ 0.188093] ASID allocator initialised with 65536 entries [ 0.215679] cryptd: max_cpu_qlen set to 1000 [ 0.221943] SCSI subsystem initialized [ 0.226209] usbcore: registered new interface driver usbfs [ 0.231898] usbcore: registered new interface driver hub [ 0.237360] usbcore: registered new device driver usb [ 0.244722] clocksource: Switched to clocksource arch_sys_counter [ 0.251629] NET: Registered protocol family 2 [ 0.256252] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.264586] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.273151] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.281166] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.288665] TCP: Hash tables configured (established 8192 bind 8192) [ 0.295279] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.302035] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.309442] NET: Registered protocol family 1 [ 0.313865] PCI: CLS 0 bytes, default 64 [ 0.319278] workingset: timestamp_bits=46 max_order=18 bucket_order=0 [ 0.329539] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.335498] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.351871] mv_xor d0060900.xor: Marvell shared XOR driver [ 0.425447] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 0.505444] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 0.513130] debugfs: Directory 'd0060900.xor' with parent 'dmaengine' already present! [ 0.521424] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.529373] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.539250] loop: module loaded [ 0.545347] spi-nor spi0.0: gd25lq80c (1024 Kbytes) [ 0.550508] 1 fixed-partitions partitions found on MTD device spi0.0 [ 0.556993] Creating 1 MTD partitions on "spi0.0": [ 0.561906] 0x000000000000-0x000000100000 : "nor" [ 0.571916] orion-mdio d0032004.mdio: Cannot register MDIO bus (-16) [ 0.578448] orion-mdio: probe of d0032004.mdio failed with error -16 [ 0.585804] mvneta: register 0x243c original value: 0 [ 0.590929] mvneta: register 0x243c modified value: 70000000 [ 0.597573] mvneta d0030000.ethernet eth0: Using random mac address e2:42:19:e7:8a:68 [ 0.605836] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.612487] ehci-pci: EHCI PCI platform driver [ 0.617129] ehci-platform: EHCI generic platform driver [ 0.622584] ehci-orion: EHCI orion driver [ 0.626934] orion-ehci d005e000.usb: EHCI Host Controller [ 0.632432] orion-ehci d005e000.usb: new USB bus registered, assigned bus number 1 [ 0.640334] orion-ehci d005e000.usb: irq 23, io mem 0xd005e000 [ 0.684717] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00 [ 0.691190] hub 1-0:1.0: USB hub found [ 0.695025] hub 1-0:1.0: 1 port detected [ 0.700041] usbcore: registered new interface driver usb-storage [ 0.706363] i2c /dev entries driver [ 0.710654] armada_37xx_wdt d0008300.watchdog: Initial timeout 120 sec [ 0.717814] sdhci: Secure Digital Host Controller Interface driver [ 0.724106] sdhci: Copyright(c) Pierre Ossman [ 0.728744] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.734679] leds-gpio gpio-leds: there is not valid maps for state default [ 0.743553] NET: Registered protocol family 10 [ 0.749037] Segment Routing with IPv6 [ 0.752782] NET: Registered protocol family 17 [ 0.757365] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.760820] mmc0: SDHCI controller on d00d8000.sdhci [d00d8000.sdhci] using ADMA [ 0.770886] 8021q: 802.1Q VLAN Support v1.8 [ 0.786429] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 0, base_baud = 1562500) is a mvebu-uart [ 0.795910] printk: console [ttyMV0] enabled [ 0.795910] printk: console [ttyMV0] enabled [ 0.804639] printk: bootconsole [ar3700_uart0] disabled [ 0.804639] printk: bootconsole [ar3700_uart0] disabled [ 0.823183] xhci-hcd d0058000.usb: xHCI Host Controller [ 0.828634] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 2 [ 0.836404] xhci-hcd d0058000.usb: hcc params 0x0a000998 hci version 0x100 quirks 0x0000000000010090 [ 0.842229] mmc0: new HS400 MMC card at address 0001 [ 0.845883] xhci-hcd d0058000.usb: irq 22, io mem 0xd0058000 [ 0.846467] hub 2-0:1.0: USB hub found [ 0.860891] hub 2-0:1.0: 1 port detected [ 0.861234] mmcblk0: mmc0:0001 4FTE4R 3.64 GiB [ 0.865249] xhci-hcd d0058000.usb: xHCI Host Controller [ 0.870424] mmcblk0boot0: mmc0:0001 4FTE4R partition 1 4.00 MiB [ 0.875175] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 3 [ 0.881557] mmcblk0boot1: mmc0:0001 4FTE4R partition 2 4.00 MiB [ 0.888910] xhci-hcd d0058000.usb: Host supports USB 3.0 SuperSpeed [ 0.888986] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 0.895122] mmcblk0rpmb: mmc0:0001 4FTE4R partition 3 512 KiB, chardev (249:0) [ 0.902108] hub 3-0:1.0: USB hub found [ 0.910714] mmcblk0: p1 p2 p3 p4 [ 0.917377] hub 3-0:1.0: 1 port detected [ 0.921420] mmcblk0: p4 size 7200768 extends beyond EOD, [ 0.925369] armada-37xx-rwtm-mailbox d00b0000.mailbox: Secure processor not ready [ 0.928711] truncated [ 0.942005] turris-mox-rwtm firmware:armada-3700-rwtm: Cannot read board information: -5 [ 0.942014] armada-37xx-rwtm-mailbox d00b0000.mailbox: Secure processor not ready [ 0.960452] turris-mox-rwtm firmware:armada-3700-rwtm: Firmware does not support the GET_RANDOM command [ 0.970247] turris-mox-rwtm: probe of firmware:armada-3700-rwtm failed with error -5 [ 0.988739] VFS: Mounted root (squashfs filesystem) readonly on device 179:1. [ 0.997334] Freeing unused kernel memory: 512K [ 1.024902] Run /sbin/init as init process [ 1.246320] init: Console is alive [ 1.250005] init: - watchdog - [ 1.408997] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 1.429770] gpio-keys gpio-keys: there is not valid maps for state default [ 1.438778] ehci-fsl: Freescale EHCI Host controller driver [ 1.447205] usbcore: registered new interface driver uas [ 1.452959] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 1.465911] init: - preinit - [ 1.670182] random: fast init done [ 1.854849] random: jshn: uninitialized urandom read (4 bytes read) [ 1.890091] random: jshn: uninitialized urandom read (4 bytes read) [ 1.910821] random: jshn: uninitialized urandom read (4 bytes read) [ 1.971464] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii link mode [ 1.980283] mvneta d0030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 1.989520] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 6.175704] urandom_read: 2 callbacks suppressed [ 6.175711] random: procd: uninitialized urandom read (4 bytes read) [ 6.243150] F2FS-fs (loop0): Mounted with checkpoint version = 5ccce281 [ 6.250828] mount_root: switching to f2fs overlay [ 6.257021] overlayfs: "xino" feature enabled using 32 upper inode bits. [ 6.290251] mmcblk0p1: Can't mount, would change RO state [ 6.299692] /dev/mmcblk0p1: Can't open blockdev mount: mounting /dev/mmcblk0p1 on /boot failed: Resource busy umount: can't unmount /boot: Invalid argument [ 6.352208] random: crng init done [ 6.352426] urandom-seed: Seeding 4096 bits and crediting [ 6.361867] urandom-seed: Saving 4096 bits of creditable seed for next boot [ 6.395514] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null) [ 6.422302] mvneta d0030000.ethernet eth0: Link is Down [ 6.453806] procd: - early - [ 6.457005] procd: - watchdog - [ 7.003447] procd: - watchdog - [ 7.009687] procd: - ubus - [ 7.092738] procd: - init - Please press Enter to activate this console. [ 7.366179] urngd: v1.0.2 started. [ 7.393353] kmodloader: loading kernel modules from /etc/modules.d/* [ 7.432303] usbcore: registered new interface driver usbserial_generic [ 7.439228] usbserial: USB Serial support registered for generic [ 7.447103] usbcore: registered new interface driver ch341 [ 7.452889] usbserial: USB Serial support registered for ch341-uart [ 7.460452] usbcore: registered new interface driver cp210x [ 7.466373] usbserial: USB Serial support registered for cp210x [ 7.473703] usbcore: registered new interface driver ftdi_sio [ 7.479773] usbserial: USB Serial support registered for FTDI USB Serial Device [ 7.514762] kmodloader: done loading kernel modules from /etc/modules.d/* [ 11.069165] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii link mode [ 11.077450] mvneta d0030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 11.086934] br-lan: port 1(eth0) entered blocking state [ 11.092336] br-lan: port 1(eth0) entered disabled state [ 11.098020] device eth0 entered promiscuous mode [ 11.105165] br-lan: port 1(eth0) entered blocking state [ 11.110571] br-lan: port 1(eth0) entered forwarding state [ 12.114807] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready