1. TIM-1.0
2. WTMI-armada-17.10.3-d61ed3a
3. WTMI: system early-init
4. ​
5. DDR topology parameters:
6. ========================
7. ddr type DDR3
8. ddr speedbin 12
9. bus width 16-bits
10. cs num 2
11. cs[0] - group num 0
12. cs[0] - bank num 8
13. cs[0] - capacity 512MiB
14. cs[1] - group num 0
15. cs[1] - bank num 8
16. cs[1] - capacity 512MiB
17. ​
18. DRAM windows:
19. =============
20. WIN[0] - base addr 0x60000000
21. WIN[0] - size 0x40000000
22. WIN[1] - base addr 0xa0000000
23. WIN[1] - size 0x20000000
24. ​
25. memory test region:
26. ===================
27. CS[0] 0x60000000 - 0x7fffffff
28. CS[1] 0x80000000 - 0x9fffffff
29. ​
30. Fill memory before self refresh...done
31. ​
32. Fill memory before self refresh...done
33. ​
34. Now in Self-refresh Mode
35. Restore termination values to original values
36. Exited self-refresh ...
37. ​
38. ​
39. Self refresh Pass.
40. DDR self test mode test done!!
41. ​
42. Self refresh Pass.
43. DDR self test mode test done!!
44. ​
45. QS GATING
46. =============
47. Calibration done: cycle = 0x00 tap =0x5F
48. CH0_PHY_RL_Control_CS0_B0[0xC0001180]: 0x0000005F
49. CH0_PHY_RL_Control_CS0_B1[0xC0001184]: 0x0000005F
50. ​
51. ​
52. QS GATING
53. =============
54. Calibration done: cycle = 0x00 tap =0x5C
55. CH0_PHY_RL_Control_CS1_B0[0xC00011A4]: 0x0000005C
56. CH0_PHY_RL_Control_CS1_B1[0xC00011A8]: 0x0000005C
57. ​
58. DLL TUNING
59. ==============
60. DLL 0xc0001050[21:16]: [0,2f,17]
61. DLL 0xc0001050[29:24]: [4,32,1b]
62. DLL 0xc0001054[21:16]: [0,2c,16]
63. DLL 0xc0001054[29:24]: [9,34,1e]
64. DLL 0xc0001074[21:16]: [0,3f,1f]
65. DLL 0xc0001074NOTICE: Booting Trusted Firmware
66. NOTICE: BL1: v1.3(debug):armada-17.10.7:16571d2
67. NOTICE: BL1: Built : 15:51:32, Apr 19 2NOTICE: BL2: v1.3(debug):armada-17.10.7:16571d2
68. NOTICE: BL2: Built : 15:51:34, Apr 19 2018NOTICE: BL31: v1.3(debug):armada-17.10.7:16571d2
69. NOTICE: BL31:
70. ​
71. U-Boot 2017.03-armada-17.10.1 (Dec 29 2018 - 11:26:46 +0800)
72. ​
73. Model: Marvell Armada 3720 ECK Board
74. CPU @ 1000 [MHz]
75. L2 @ 800 [MHz]
76. TClock @ 200 [MHz]
77. DDR @ 800 [MHz]
78. DRAM: 1 GiB
79. U-Boot DT blob at : 000000003f71b328
80. Comphy-0: USB3 5 Gbps
81. Comphy-1: PEX0 2.5 Gbps
82. Comphy-2: SATA0 6 Gbps
83. MMC: sdhci@d8000: 0
84. SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB
85. *** Warning - bad CRC, using default environment
86. ​
87. Net: SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB
88. Factory mac is : B0-A7-B9-8E-EC-F1
89. eth0: neta@30000 [PRIME]
90. Attach switch ID 0x004dd043
91. Attach switch driver for AR8236
92. Checking for firmware recovery mode...
93. Reset button not pushed, do nothing
94. Press CTRL+B to abort autoboot in 1 seconds
95. switch to partitions #0, OK
96. mmc0(part 0) is current device
97. ​
98. MMC read: dev # 0, block # 896, count 128 ... 128 blocks read: OK
99. switch to partitions #0, OK
100. mmc0(part 0) is current device
101. ​
102. MMC read: dev # 0, block # 1024, count 32768 ... 32768 blocks read: OK
103. ## Flattened Device Tree blob at 04f00000
104. Booting using the fdt blob at 0x4f00000
105. Using Device Tree in place at 0000000004f00000, end 0000000004f05d3b
106. ​
107. Starting kernel ...
108. ​
109. [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
110. [ 0.000000] Linux version 5.10.109 (aholmes@astraea-lnx) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19336-374f325afbf) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Mar 31 01:54:14 2022
111. [ 0.000000] Machine model: Marvell Armada 3720 ECK Board
112. [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '')
113. [ 0.000000] printk: bootconsole [ar3700_uart0] enabled
114. [ 0.000000] efi: UEFI not found.
115. [ 0.000000] Zone ranges:
116. [ 0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff]
117. [ 0.000000] DMA32 empty
118. [ 0.000000] Normal empty
119. [ 0.000000] Movable zone start for each node
120. [ 0.000000] Early memory node ranges
121. [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
122. [ 0.000000] node 0: [mem 0x0000000004000000-0x00000000041fffff]
123. [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff]
124. [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
125. [ 0.000000] psci: probing for conduit method from DT.
126. [ 0.000000] psci: PSCIv1.0 detected in firmware.
127. [ 0.000000] psci: Using standard PSCI v0.2 function IDs
128. [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
129. [ 0.000000] psci: SMC Calling Convention v1.0
130. [ 0.000000] percpu: Embedded 16 pages/cpu s28248 r8192 d29096 u65536
131. [ 0.000000] Detected VIPT I-cache on CPU0
132. [ 0.000000] CPU features: detected: GIC system register CPU interface
133. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
134. [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000 mtdparts=spi0.0:1M(nor-flash) root=/dev/mmcblk0p1 rw rootwait
135. [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
136. [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
137. [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
138. [ 0.000000] Memory: 1014196K/1048576K available (8256K kernel code, 878K rwdata, 2068K rodata, 512K init, 284K bss, 34380K reserved, 0K cma-reserved)
139. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
140. [ 0.000000] rcu: Hierarchical RCU implementation.
141. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
142. [ 0.000000] Tracing variant of Tasks RCU enabled.
143. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
144. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
145. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
146. [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
147. [ 0.000000] GICv3: 192 SPIs implemented
148. [ 0.000000] GICv3: 0 Extended SPIs implemented
149. [ 0.000000] GICv3: Distributor has no Range Selector support
150. [ 0.000000] GICv3: 16 PPIs implemented
151. [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
152. [ 0.000000] random: get_random_bytes called from start_kernel+0x3a8/0x57c with crng_init=0
153. [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
154. [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
155. [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
156. [ 0.008364] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
157. [ 0.018957] pid_max: default: 32768 minimum: 301
158. [ 0.023815] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
159. [ 0.031365] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
160. [ 0.040701] rcu: Hierarchical SRCU implementation.
161. [ 0.045721] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
162. [ 0.053638] EFI services will not be available.
163. [ 0.058385] smp: Bringing up secondary CPUs ...
164. [ 0.063335] Detected VIPT I-cache on CPU1
165. [ 0.063370] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000
166. [ 0.063414] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
167. [ 0.063507] smp: Brought up 1 node, 2 CPUs
168. [ 0.085565] SMP: Total of 2 processors activated.
169. [ 0.090398] CPU features: detected: 32-bit EL0 Support
170. [ 0.095690] CPU features: detected: CRC32 instructions
171. [ 0.101015] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
172. [ 0.109581] CPU: All CPU(s) started at EL2
173. [ 0.113792] alternatives: patching kernel code
174. [ 0.121101] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
175. [ 0.131190] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
176. [ 0.138265] pinctrl core: initialized pinctrl subsystem
177. [ 0.144101] DMI not present or invalid.
178. [ 0.148454] NET: Registered protocol family 16
179. [ 0.153383] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
180. [ 0.160628] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
181. [ 0.168567] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
182. [ 0.177063] thermal_sys: Registered thermal governor 'step_wise'
183. [ 0.177599] cpuidle: using governor ladder
184. [ 0.188093] ASID allocator initialised with 65536 entries
185. [ 0.215679] cryptd: max_cpu_qlen set to 1000
186. [ 0.221943] SCSI subsystem initialized
187. [ 0.226209] usbcore: registered new interface driver usbfs
188. [ 0.231898] usbcore: registered new interface driver hub
189. [ 0.237360] usbcore: registered new device driver usb
190. [ 0.244722] clocksource: Switched to clocksource arch_sys_counter
191. [ 0.251629] NET: Registered protocol family 2
192. [ 0.256252] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
193. [ 0.264586] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
194. [ 0.273151] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
195. [ 0.281166] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
196. [ 0.288665] TCP: Hash tables configured (established 8192 bind 8192)
197. [ 0.295279] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
198. [ 0.302035] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
199. [ 0.309442] NET: Registered protocol family 1
200. [ 0.313865] PCI: CLS 0 bytes, default 64
201. [ 0.319278] workingset: timestamp_bits=46 max_order=18 bucket_order=0
202. [ 0.329539] squashfs: version 4.0 (2009/01/31) Phillip Lougher
203. [ 0.335498] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
204. [ 0.351871] mv_xor d0060900.xor: Marvell shared XOR driver
205. [ 0.425447] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
206. [ 0.505444] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
207. [ 0.513130] debugfs: Directory 'd0060900.xor' with parent 'dmaengine' already present!
208. [ 0.521424] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
209. [ 0.529373] cacheinfo: Unable to detect cache hierarchy for CPU 0
210. [ 0.539250] loop: module loaded
211. [ 0.545347] spi-nor spi0.0: gd25lq80c (1024 Kbytes)
212. [ 0.550508] 1 fixed-partitions partitions found on MTD device spi0.0
213. [ 0.556993] Creating 1 MTD partitions on "spi0.0":
214. [ 0.561906] 0x000000000000-0x000000100000 : "nor"
215. [ 0.571916] orion-mdio d0032004.mdio: Cannot register MDIO bus (-16)
216. [ 0.578448] orion-mdio: probe of d0032004.mdio failed with error -16
217. [ 0.585804] mvneta: register 0x243c original value: 0
218. [ 0.590929] mvneta: register 0x243c modified value: 70000000
219. [ 0.597573] mvneta d0030000.ethernet eth0: Using random mac address e2:42:19:e7:8a:68
220. [ 0.605836] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
221. [ 0.612487] ehci-pci: EHCI PCI platform driver
222. [ 0.617129] ehci-platform: EHCI generic platform driver
223. [ 0.622584] ehci-orion: EHCI orion driver
224. [ 0.626934] orion-ehci d005e000.usb: EHCI Host Controller
225. [ 0.632432] orion-ehci d005e000.usb: new USB bus registered, assigned bus number 1
226. [ 0.640334] orion-ehci d005e000.usb: irq 23, io mem 0xd005e000
227. [ 0.684717] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00
228. [ 0.691190] hub 1-0:1.0: USB hub found
229. [ 0.695025] hub 1-0:1.0: 1 port detected
230. [ 0.700041] usbcore: registered new interface driver usb-storage
231. [ 0.706363] i2c /dev entries driver
232. [ 0.710654] armada_37xx_wdt d0008300.watchdog: Initial timeout 120 sec
233. [ 0.717814] sdhci: Secure Digital Host Controller Interface driver
234. [ 0.724106] sdhci: Copyright(c) Pierre Ossman
235. [ 0.728744] sdhci-pltfm: SDHCI platform and OF driver helper
236. [ 0.734679] leds-gpio gpio-leds: there is not valid maps for state default
237. [ 0.743553] NET: Registered protocol family 10
238. [ 0.749037] Segment Routing with IPv6
239. [ 0.752782] NET: Registered protocol family 17
240. [ 0.757365] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
241. [ 0.760820] mmc0: SDHCI controller on d00d8000.sdhci [d00d8000.sdhci] using ADMA
242. [ 0.770886] 8021q: 802.1Q VLAN Support v1.8
243. [ 0.786429] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 0, base_baud = 1562500) is a mvebu-uart
244. [ 0.795910] printk: console [ttyMV0] enabled
245. [ 0.795910] printk: console [ttyMV0] enabled
246. [ 0.804639] printk: bootconsole [ar3700_uart0] disabled
247. [ 0.804639] printk: bootconsole [ar3700_uart0] disabled
248. [ 0.823183] xhci-hcd d0058000.usb: xHCI Host Controller
249. [ 0.828634] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 2
250. [ 0.836404] xhci-hcd d0058000.usb: hcc params 0x0a000998 hci version 0x100 quirks 0x0000000000010090
251. [ 0.842229] mmc0: new HS400 MMC card at address 0001
252. [ 0.845883] xhci-hcd d0058000.usb: irq 22, io mem 0xd0058000
253. [ 0.846467] hub 2-0:1.0: USB hub found
254. [ 0.860891] hub 2-0:1.0: 1 port detected
255. [ 0.861234] mmcblk0: mmc0:0001 4FTE4R 3.64 GiB
256. [ 0.865249] xhci-hcd d0058000.usb: xHCI Host Controller
257. [ 0.870424] mmcblk0boot0: mmc0:0001 4FTE4R partition 1 4.00 MiB
258. [ 0.875175] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 3
259. [ 0.881557] mmcblk0boot1: mmc0:0001 4FTE4R partition 2 4.00 MiB
260. [ 0.888910] xhci-hcd d0058000.usb: Host supports USB 3.0 SuperSpeed
261. [ 0.888986] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
262. [ 0.895122] mmcblk0rpmb: mmc0:0001 4FTE4R partition 3 512 KiB, chardev (249:0)
263. [ 0.902108] hub 3-0:1.0: USB hub found
264. [ 0.910714] mmcblk0: p1 p2 p3 p4
265. [ 0.917377] hub 3-0:1.0: 1 port detected
266. [ 0.921420] mmcblk0: p4 size 7200768 extends beyond EOD,
267. [ 0.925369] armada-37xx-rwtm-mailbox d00b0000.mailbox: Secure processor not ready
268. [ 0.928711] truncated
269. [ 0.942005] turris-mox-rwtm firmware:armada-3700-rwtm: Cannot read board information: -5
270. [ 0.942014] armada-37xx-rwtm-mailbox d00b0000.mailbox: Secure processor not ready
271. [ 0.960452] turris-mox-rwtm firmware:armada-3700-rwtm: Firmware does not support the GET_RANDOM command
272. [ 0.970247] turris-mox-rwtm: probe of firmware:armada-3700-rwtm failed with error -5
273. [ 0.988739] VFS: Mounted root (squashfs filesystem) readonly on device 179:1.
274. [ 0.997334] Freeing unused kernel memory: 512K
275. [ 1.024902] Run /sbin/init as init process
276. [ 1.246320] init: Console is alive
277. [ 1.250005] init: - watchdog -
278. [ 1.408997] kmodloader: loading kernel modules from /etc/modules-boot.d/*
279. [ 1.429770] gpio-keys gpio-keys: there is not valid maps for state default
280. [ 1.438778] ehci-fsl: Freescale EHCI Host controller driver
281. [ 1.447205] usbcore: registered new interface driver uas
282. [ 1.452959] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
283. [ 1.465911] init: - preinit -
284. [ 1.670182] random: fast init done
285. [ 1.854849] random: jshn: uninitialized urandom read (4 bytes read)
286. [ 1.890091] random: jshn: uninitialized urandom read (4 bytes read)
287. [ 1.910821] random: jshn: uninitialized urandom read (4 bytes read)
288. [ 1.971464] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii link mode
289. [ 1.980283] mvneta d0030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
290. [ 1.989520] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
291. Press the [f] key and hit [enter] to enter failsafe mode
292. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
293. [ 6.175704] urandom_read: 2 callbacks suppressed
294. [ 6.175711] random: procd: uninitialized urandom read (4 bytes read)
295. [ 6.243150] F2FS-fs (loop0): Mounted with checkpoint version = 5ccce281
296. [ 6.250828] mount_root: switching to f2fs overlay
297. [ 6.257021] overlayfs: "xino" feature enabled using 32 upper inode bits.
298. [ 6.290251] mmcblk0p1: Can't mount, would change RO state
299. [ 6.299692] /dev/mmcblk0p1: Can't open blockdev
300. mount: mounting /dev/mmcblk0p1 on /boot failed: Resource busy
301. umount: can't unmount /boot: Invalid argument
302. [ 6.352208] random: crng init done
303. [ 6.352426] urandom-seed: Seeding 4096 bits and crediting
304. [ 6.361867] urandom-seed: Saving 4096 bits of creditable seed for next boot
305. [ 6.395514] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
306. [ 6.422302] mvneta d0030000.ethernet eth0: Link is Down
307. [ 6.453806] procd: - early -
308. [ 6.457005] procd: - watchdog -
309. [ 7.003447] procd: - watchdog -
310. [ 7.009687] procd: - ubus -
311. [ 7.092738] procd: - init -
312. Please press Enter to activate this console.
313. [ 7.366179] urngd: v1.0.2 started.
314. [ 7.393353] kmodloader: loading kernel modules from /etc/modules.d/*
315. [ 7.432303] usbcore: registered new interface driver usbserial_generic
316. [ 7.439228] usbserial: USB Serial support registered for generic
317. [ 7.447103] usbcore: registered new interface driver ch341
318. [ 7.452889] usbserial: USB Serial support registered for ch341-uart
319. [ 7.460452] usbcore: registered new interface driver cp210x
320. [ 7.466373] usbserial: USB Serial support registered for cp210x
321. [ 7.473703] usbcore: registered new interface driver ftdi_sio
322. [ 7.479773] usbserial: USB Serial support registered for FTDI USB Serial Device
323. [ 7.514762] kmodloader: done loading kernel modules from /etc/modules.d/*
324. [ 11.069165] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii link mode
325. [ 11.077450] mvneta d0030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
326. [ 11.086934] br-lan: port 1(eth0) entered blocking state
327. [ 11.092336] br-lan: port 1(eth0) entered disabled state
328. [ 11.098020] device eth0 entered promiscuous mode
329. [ 11.105165] br-lan: port 1(eth0) entered blocking state
330. [ 11.110571] br-lan: port 1(eth0) entered forwarding state
331. [ 12.114807] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready