Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.110 (aholmes@astraea-lnx) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19375-77f278b3fbf) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Mon Apr 11 12:55:13 2022 [ 0.000000] Machine model: TP-Link Omada OC200 [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '') [ 0.000000] printk: bootconsole [ar3700_uart0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] node 0: [mem 0x0000000004000000-0x00000000041fffff] [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 16 pages/cpu s28248 r8192 d29096 u65536 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048 [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000 mtdparts=spi0.0:1M(nor-flash) root=/dev/mmcblk0p1 rw rootwait dyndbg=file drivers/net/* +pflm [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1013744K/1048576K available (8448K kernel code, 956K rwdata, 2224K rodata, 512K init, 286K bss, 34832K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 192 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000 [ 0.000000] random: get_random_bytes called from start_kernel+0x3a8/0x57c with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns [ 0.008366] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000) [ 0.018960] pid_max: default: 32768 minimum: 301 [ 0.023823] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.031371] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.040708] rcu: Hierarchical SRCU implementation. [ 0.045950] dyndbg: bad flag-op f, at start of file [ 0.050893] dyndbg: flags parse failed [ 0.054861] EFI services will not be available. [ 0.059636] smp: Bringing up secondary CPUs ... [ 0.064592] Detected VIPT I-cache on CPU1 [ 0.064627] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000 [ 0.064671] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.064763] smp: Brought up 1 node, 2 CPUs [ 0.086821] SMP: Total of 2 processors activated. [ 0.091655] CPU features: detected: 32-bit EL0 Support [ 0.096946] CPU features: detected: CRC32 instructions [ 0.102271] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.110838] CPU: All CPU(s) started at EL2 [ 0.115049] alternatives: patching kernel code [ 0.122475] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.132565] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.139640] pinctrl core: initialized pinctrl subsystem [ 0.145476] DMI not present or invalid. [ 0.149837] NET: Registered protocol family 16 [ 0.154789] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.162037] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.169974] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.178469] thermal_sys: Registered thermal governor 'step_wise' [ 0.178964] cpuidle: using governor ladder [ 0.189493] ASID allocator initialised with 65536 entries [ 0.217079] cryptd: max_cpu_qlen set to 1000 [ 0.223376] SCSI subsystem initialized [ 0.227640] usbcore: registered new interface driver usbfs [ 0.233331] usbcore: registered new interface driver hub [ 0.238794] usbcore: registered new device driver usb [ 0.246170] clocksource: Switched to clocksource arch_sys_counter [ 0.253077] NET: Registered protocol family 2 [ 0.257719] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.266054] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.274629] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.282650] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.290133] TCP: Hash tables configured (established 8192 bind 8192) [ 0.296754] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.303510] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.310914] NET: Registered protocol family 1 [ 0.315337] PCI: CLS 0 bytes, default 64 [ 0.320790] workingset: timestamp_bits=46 max_order=18 bucket_order=0 [ 0.330992] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.336952] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.354305] mv_xor d0060900.xor: Marvell shared XOR driver [ 0.436865] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 0.506896] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 0.514575] debugfs: Directory 'd0060900.xor' with parent 'dmaengine' already present! [ 0.522866] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.530813] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.540696] loop: module loaded [ 0.546825] spi-nor spi0.0: gd25lq80c (1024 Kbytes) [ 0.551995] 2 fixed-partitions partitions found on MTD device spi0.0 [ 0.558612] Creating 2 MTD partitions on "spi0.0": [ 0.563464] 0x000000000000-0x0000000f0000 : "u-boot" [ 0.569137] 0x0000000f0000-0x000000100000 : "u-boot-env" [ 0.581926] mvneta: register 0x243c original value: 70000000 [ 0.587726] mvneta: register 0x243c modified value: 70000000 [ 0.594297] mvneta d0030000.ethernet eth0: Using hardware mac address b0:a7:b9:8e:ec:f1 [ 0.602742] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.609427] ehci-pci: EHCI PCI platform driver [ 0.614023] ehci-platform: EHCI generic platform driver [ 0.619510] ehci-orion: EHCI orion driver [ 0.623843] orion-ehci d005e000.usb: EHCI Host Controller [ 0.629354] orion-ehci d005e000.usb: new USB bus registered, assigned bus number 1 [ 0.637251] orion-ehci d005e000.usb: irq 23, io mem 0xd005e000 [ 0.676194] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00 [ 0.682715] hub 1-0:1.0: USB hub found [ 0.686544] hub 1-0:1.0: 1 port detected [ 0.691618] usbcore: registered new interface driver usb-storage [ 0.697948] i2c /dev entries driver [ 0.702286] armada_37xx_wdt d0008300.watchdog: Initial timeout 120 sec [ 0.709446] sdhci: Secure Digital Host Controller Interface driver [ 0.715736] sdhci: Copyright(c) Pierre Ossman [ 0.720385] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.726345] leds-gpio leds: there is not valid maps for state default [ 0.734754] NET: Registered protocol family 10 [ 0.740320] Segment Routing with IPv6 [ 0.744065] NET: Registered protocol family 17 [ 0.748648] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.752452] mmc0: SDHCI controller on d00d8000.sdhci [d00d8000.sdhci] using ADMA [ 0.762151] 8021q: 802.1Q VLAN Support v1.8 [ 0.777697] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 0, base_baud = 1562500) is a mvebu-uart [ 0.787177] printk: console [ttyMV0] enabled [ 0.787177] printk: console [ttyMV0] enabled [ 0.795907] printk: bootconsole [ar3700_uart0] disabled [ 0.795907] printk: bootconsole [ar3700_uart0] disabled [ 0.813867] ar8k d0032004.mdio-mii:10: configuring for fixed/mii link mode [ 0.821011] Unable to handle kernel read from unreadable memory at virtual address 0000000000000470 [ 0.830350] Mem abort info: [ 0.833226] ESR = 0x96000005 [ 0.833687] mmc0: new HS400 MMC card at address 0001 [ 0.836376] EC = 0x25: DABT (current EL), IL = 32 bits [ 0.836379] SET = 0, FnV = 0 [ 0.836381] EA = 0, S1PTW = 0 [ 0.836383] Data abort info: [ 0.836385] ISV = 0, ISS = 0x00000005 [ 0.836387] CM = 0, WnR = 0 [ 0.836390] [0000000000000470] user address but active_mm is swapper [ 0.836396] Internal error: Oops: 96000005 [#1] SMP [ 0.836399] Modules linked in: [ 0.836411] CPU: 1 PID: 397 Comm: kworker/1:5 Not tainted 5.10.110 #0 [ 0.836413] Hardware name: TP-Link Omada OC200 (DT) [ 0.836432] Workqueue: events deferred_probe_work_func [ 0.842446] mmcblk0: mmc0:0001 4FTE4R 3.64 GiB [ 0.847024] pstate: 40400005 (nZcv daif +PAN -UAO -TCO BTYPE=--) [ 0.847032] pc : mutex_lock+0xc/0x44 [ 0.847038] lr : ar8k_regmap_update_bits+0x34/0xc4 [ 0.847041] sp : ffffffc0117a3890 [ 0.847044] x29: ffffffc0117a3890 x28: 0000000000000000 [ 0.847051] x27: ffffff8001eef8b0 x26: ffffffc0117a3b30 [ 0.847056] x25: 0000000000000000 x24: 0000000000000470 [ 0.847062] x23: 0000000000000000 x22: 0000000000000000 [ 0.850529] mmcblk0boot0: mmc0:0001 4FTE4R partition 1 4.00 MiB [ 0.853446] [ 0.856708] mmcblk0boot1: mmc0:0001 4FTE4R partition 2 4.00 MiB [ 0.860357] x21: 0000000000001200 [ 0.863499] mmcblk0rpmb: mmc0:0001 4FTE4R partition 3 512 KiB, chardev (249:0) [ 0.869953] x20: ffffff8001dc2880 [ 0.869956] x19: 0000000000000100 x18: 0000000000000091 [ 0.869962] x17: 000000000000000e x16: 0000000000000001 [ 0.875776] mmcblk0: p1 p2 p3 p4 [ 0.878132] x15: ffffffc010b276c8 x14: 00000000000001b3 [ 0.878137] x13: 0000000000000091 x12: ffffffc0117a36c8 [ 0.878143] x11: ffffffc010b7f6c8 x10: 00000000fffff000 [ 0.878149] x9 : ffffffc010b7f6c8 x8 : 0000000000000001 [ 0.878154] x7 : 0000000000000008 x6 : ffffffc01057e164 [ 0.884981] mmcblk0: p4 size 7200768 extends beyond EOD, [ 0.889825] x5 : 0000000000000001 x4 : ffffff8001ec4e00 [ 0.889830] x3 : 0000000000000000 x2 : ffffff8001834500 [ 0.889836] x1 : 0000000000000000 x0 : 0000000000000470 [ 0.895135] truncated [ 0.899799] Call trace: [ 0.899806] mutex_lock+0xc/0x44 [ 0.899813] ar8k_phylink_mac_config+0x2c/0xa0 [ 1.044491] dsa_port_phylink_mac_config+0x34/0x4c [ 1.049433] phylink_mac_config+0x58/0x220 [ 1.053655] phylink_major_config+0x6c/0x284 [ 1.058056] phylink_mac_initial_config+0x8c/0xfc [ 1.062904] phylink_start+0x48/0x280 [ 1.066679] dsa_port_enable_rt+0x50/0x90 [ 1.070811] dsa_port_enable+0x28/0x4c [ 1.074673] dsa_register_switch+0x538/0xc00 [ 1.079073] ar8k_sw_probe+0x1e4/0x240 [ 1.082937] mdio_probe+0x34/0x70 [ 1.086354] really_probe+0x108/0x4f0 [ 1.090127] driver_probe_device+0x90/0x134 [ 1.094439] __device_attach_driver+0xa0/0x120 [ 1.099018] bus_for_each_drv+0x68/0xb0 [ 1.102970] __device_attach+0xd0/0x144 [ 1.106922] device_initial_probe+0x14/0x20 [ 1.111233] bus_probe_device+0x9c/0xa4 [ 1.115185] deferred_probe_work_func+0xa4/0xf4 [ 1.119856] process_one_work+0x1d4/0x380 [ 1.123987] worker_thread+0x298/0x4e0 [ 1.127853] kthread+0x124/0x12c [ 1.131180] ret_from_fork+0x10/0x3c [ 1.134871] Code: d65f03c0 d2800001 d5384102 f9800011 (c85ffc03) [ 1.141156] ---[ end trace 2bb4c0b7542287bb ]--- [ 1.145916] Kernel panic - not syncing: Oops: Fatal exception [ 1.151842] SMP: stopping secondary CPUs [ 1.155888] Kernel Offset: disabled [ 1.159482] CPU features: 0x0000002,00002008 [ 1.163880] Memory Limit: none [ 1.167028] Rebooting in 1 seconds.. TIM-1.0 WTMI-armada-17.10.3-d61ed3a WTMI: system early-init DDR topology parameters: ======================== ddr type DDR3 ddr speedbin 12 bus width 16-bits cs num 2 cs[0] - group num 0 cs[0] - bank num 8 cs[0] - capacity 512MiB cs[1] - group num 0 cs[1] - bank num 8 cs[1] - capacity 512MiB DRAM windows: ============= WIN[0] - base addr 0x60000000 WIN[0] - size 0x40000000 WIN[1] - base addr 0xa0000000 WIN[1] - size 0x20000000 memory test region: =================== CS[0] 0x60000000 - 0x7fffffff CS[1] 0x80000000 - 0x9fffffff Fill memory before self refresh...done Fill memory before self refresh...done Now in Self-refresh Mode Restore termination values to original values Exited self-refresh ... Self refresh Pass. DDR self test mode test done!! Self refresh Pass. DDR self test mode test done!! QS GATING ============= Calibration done: cycle = 0x00 tap =0x5A CH0_PHY_RL_Control_CS0_B0[0xC0001180]: 0x0000005A CH0_PHY_RL_Control_CS0_B1[0xC0001184]: 0x0000005A QS GATING ============= Calibration done: cycle = 0x00 tap =0x5C CH0_PHY_RL_Control_CS1_B0[0xC00011A4]: 0x0000005C CH0_PHY_RL_Control_CS1_B1[0xC00011A8]: 0x0000005C DLL TUNING ============== DLL 0xc0001050[21:16]: [0,31,18] DLL 0xc0001050[29:24]: [4,33,1b] DLL 0xc0001054[21:16]: [1,2c,16] DLL 0xc0001054[29:24]: [9,2f,1c] DLL 0xc0001074[21:16]: [0,3f,1f] DLL 0xc0001074NOTICE: Booting Trusted Firmware NOTICE: BL1: v1.3(debug):armada-17.10.7:16571d2 NOTICE: BL1: Built : 15:51:32, Apr 19 2NOTICE: BL2: v1.3(debug):armada-17.10.7:16571d2 NOTICE: BL2: Built : 15:51:34, Apr 19 2018NOTICE: BL31: v1.3(debug):armada-17.10.7:16571d2 NOTICE: BL31: U-Boot 2017.03-armada-17.10.1 (Dec 29 2018 - 11:26:46 +0800) Model: Marvell Armada 3720 ECK Board CPU @ 1000 [MHz] L2 @ 800 [MHz] TClock @ 200 [MHz] DDR @ 800 [MHz] DRAM: 1 GiB U-Boot DT blob at : 000000003f71b328 Comphy-0: USB3 5 Gbps Comphy-1: PEX0 2.5 Gbps Comphy-2: SATA0 6 Gbps MMC: sdhci@d8000: 0 SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB Net: SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB Factory mac is : B0-A7-B9-8E-EC-F1 eth0: neta@30000 [PRIME] Attach switch ID 0x004dd043 Attach switch driver for AR8236 Checking for firmware recovery mode... Reset button not pushed, do nothing Press CTRL+B to abort autoboot in 5 seconds Marvell>>