1. U-Boot 2012.07 (Nov 21 2017 - 10:06:29)
2. ​
3. smem ram ptable found: ver: 0 len: 5
4. DRAM: 1 GiB
5. NAND: Detected MICRON MT29F4G08ABBDAH4, total 512 MiB
6. SF: Detected MX25U3235F with page size 4 KiB, total 4 MiB
7. PCI0 Link Intialized
8. PCI1 Link Intialized
9. In: serial
10. Out: serial
11. Err: serial
12. ​
13. PHY ID = 0x4dd074, eth0 found AR8033 PHY
14. MAC2 addr:7c:5a:1c:34:61:82
15. PHY ID = 0x4dd074, eth1 found AR8033 PHY
16. MAC3 addr:7c:5a:1c:34:61:83
17. eth0, eth1
18. Creating 1 MTD partitions on "nand0":
19. 0x000000000000-0x000020000000 : "mtd=0"
20. UBI: attaching mtd2 to ubi0
21. UBI: physical eraseblock size: 131072 bytes (128 KiB)
22. UBI: logical eraseblock size: 126976 bytes
23. UBI: smallest flash I/O unit: 2048
24. UBI: VID header offset: 2048 (aligned 2048)
25. UBI: data offset: 4096
26. UBI: attached mtd2 to ubi0
27. UBI: MTD device name: "mtd=0"
28. UBI: MTD device size: 512 MiB
29. UBI: number of good PEBs: 4096
30. UBI: number of bad PEBs: 0
31. UBI: max. allowed volumes: 128
32. UBI: wear-leveling threshold: 4096
33. UBI: number of internal volumes: 1
34. UBI: number of user volumes: 3
35. UBI: available PEBs: 40
36. UBI: total number of reserved PEBs: 4056
37. UBI: number of PEBs reserved for bad PEB handling: 40
38. UBI: max/mean erase counter: 29/5
39. SF: Detected MX25U3235F with page size 4 KiB, total 4 MiB
40. Hit any key to stop autoboot: 0
41. Read 0 bytes from volume image to 44000000
42. No size specified -> Using max size (3174400)
43. ## Booting kernel from FIT Image at 44000000 ...
44. Using 'config@2' configuration
45. Trying 'kernel-1' kernel subimage
46. Description: ARM OpenWrt Linux-5.10.90
47. Type: Kernel Image
48. Compression: uncompressed
49. Data Start: 0x440000e4
50. Data Size: 3132784 Bytes = 3 MiB
51. Architecture: ARM
52. OS: Linux
53. Load Address: 0x42208000
54. Entry Point: 0x42208000
55. node name: hash@1
56. Hash algo: crc32
57. Hash value: 4bb2f5fe
58. node name: hash@2
59. Hash algo: sha1
60. Hash value: 02a44539187ac6baeaafa81bc39288c6f7bdac1c
61. ## Flattened Device Tree from FIT Image at 44000000
62. Using 'config@2' configuration
63. Trying 'fdt-1' FDT blob subimage
64. Description: ARM OpenWrt sophos_apx530 device tree blob
65. Type: Flat Device Tree
66. Compression: uncompressed
67. Data Start: 0x442fcf8c
68. Data Size: 30647 Bytes = 29.9 KiB
69. Architecture: ARM
70. node name: hash@1
71. Hash algo: crc32
72. Hash value: 643eb210
73. node name: hash@2
74. Hash algo: sha1
75. Hash value: ed779c0ad98334bdb811afe7d36de10dc92120d9
76. Booting using the fdt blob at 0x442fcf8c
77. Loading Kernel Image ... OK
78. OK
79. Using Device Tree in place at 442fcf8c, end 44307742
80. Using machid 0x136c from environment
81. ​
82. Starting kernel ...
83. ​
84. [ 0.000000] Booting Linux on physical CPU 0x0
85. [ 0.000000] Linux version 5.10.90 (neg2led@astraea) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r18592-6e02b3c482) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Mon Jan 17 06:44:52 2022
86. [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
87. [ 0.000000] CPU: div instructions available: patching division code
88. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
89. [ 0.000000] OF: fdt: Machine model: Sophos APX530
90. [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x42000000
91. [ 0.000000] earlycon: msm_serial_dm0 at MMIO 0x16340000 (options '')
92. [ 0.000000] printk: bootconsole [msm_serial_dm0] enabled
93. [ 0.000000] Memory policy: Data cache writealloc
94. [ 0.000000] BUG: mapping for 0x16640000 at 0xf0040000 out of vmalloc space
95. [ 0.000000] Zone ranges:
96. [ 0.000000] Normal [mem 0x0000000042000000-0x0000000071ffffff]
97. [ 0.000000] HighMem [mem 0x0000000072000000-0x000000007fffffff]
98. [ 0.000000] Movable zone start for each node
99. [ 0.000000] Early memory node ranges
100. [ 0.000000] node 0: [mem 0x0000000042000000-0x000000007fffffff]
101. [ 0.000000] Initmem setup node 0 [mem 0x0000000042000000-0x000000007fffffff]
102. [ 0.000000] On node 0 totalpages: 253952
103. [ 0.000000] Normal zone: 1728 pages used for memmap
104. [ 0.000000] Normal zone: 0 pages reserved
105. [ 0.000000] Normal zone: 196608 pages, LIFO batch:63
106. [ 0.000000] HighMem zone: 57344 pages, LIFO batch:15
107. [ 0.000000] percpu: Embedded 15 pages/cpu s30796 r8192 d22452 u61440
108. [ 0.000000] pcpu-alloc: s30796 r8192 d22452 u61440 alloc=15*4096
109. [ 0.000000] pcpu-alloc: [0] 0 [0] 1
110. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 252224
111. [ 0.000000] Kernel command line: ubi.mtd=rootfs loglevel=8 console=ttyMSM0,115200 ubi.block=0,rootfs root=/dev/ubiblock0_1 rootfstype=squashfs earlycon=msm_serial_dm,0x16340000
112. [ 0.000000] Bootloader command line not present
113. [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
114. [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
115. [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
116. [ 0.000000] Memory: 994672K/1015808K available (6930K kernel code, 656K rwdata, 1764K rodata, 1024K init, 242K bss, 21136K reserved, 0K cma-reserved, 229376K highmem)
117. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
118. [ 0.000000] rcu: Hierarchical RCU implementation.
119. [ 0.000000] Tracing variant of Tasks RCU enabled.
120. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
121. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
122. [ 0.000000] random: get_random_bytes called from start_kernel+0x3a0/0x54c with crng_init=0
123. [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
124. [ 0.000009] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
125. [ 0.009633] Switching to timer-based delay loop, resolution 160ns
126. [ 0.017668] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
127. [ 0.023524] pid_max: default: 32768 minimum: 301
128. [ 0.034012] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
129. [ 0.038460] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
130. [ 0.046641] CPU: Testing write buffer coherency: ok
131. [ 0.053692] qcom_scm: convention: smc legacy
132. [ 0.059070] Setting up static identity map for 0x42300000 - 0x42300060
133. [ 0.062740] rcu: Hierarchical SRCU implementation.
134. [ 0.069865] smp: Bringing up secondary CPUs ...
135. [ 0.075591] smp: Brought up 1 node, 2 CPUs
136. [ 0.078117] SMP: Total of 2 processors activated (25.00 BogoMIPS).
137. [ 0.082371] CPU: All CPU(s) started in SVC mode.
138. [ 0.099636] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
139. [ 0.099833] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
140. [ 0.106589] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
141. [ 0.116414] pinctrl core: initialized pinctrl subsystem
142. [ 0.124294] NET: Registered protocol family 16
143. [ 0.128380] DMA: preallocated 256 KiB pool for atomic coherent allocations
144. [ 0.133974] thermal_sys: Registered thermal governor 'step_wise'
145. [ 0.136020] cpuidle: using governor ladder
146. [ 0.145673] cpuidle: using governor menu
147. [ 0.193305] usbcore: registered new interface driver usbfs
148. [ 0.193414] usbcore: registered new interface driver hub
149. [ 0.197859] usbcore: registered new device driver usb
150. [ 0.203236] pps_core: LinuxPPS API ver. 1 registered
151. [ 0.208197] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
152. [ 0.213172] PTP clock support registered
153. [ 0.224597] clocksource: Switched to clocksource dg_timer
154. [ 0.227216] NET: Registered protocol family 2
155. [ 0.231628] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
156. [ 0.237063] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
157. [ 0.243375] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
158. [ 0.251477] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
159. [ 0.259492] TCP: Hash tables configured (established 8192 bind 8192)
160. [ 0.266534] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
161. [ 0.272804] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
162. [ 0.279423] NET: Registered protocol family 1
163. [ 0.286517] PCI: CLS 0 bytes, default 64
164. [ 0.292159] workingset: timestamp_bits=14 max_order=18 bucket_order=4
165. [ 0.300426] squashfs: version 4.0 (2009/01/31) Phillip Lougher
166. [ 0.300991] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
167. [ 0.412332] bounce: pool size: 64 pages
168. [ 0.414278] gpio-export gpio-export: 4 gpio(s) exported
169. [ 0.415921] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator
170. [ 0.420398] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator
171. [ 0.428019] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator
172. [ 0.435949] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
173. [ 0.443292] qcom-pcie 1b500000.pci: Parsing ranges property...
174. [ 0.450344] qcom-pcie 1b500000.pci: IO 0x000fe00000..0x000fe0ffff -> 0x000fe00000
175. [ 0.456066] qcom-pcie 1b500000.pci: MEM 0x0008000000..0x000fdfffff -> 0x0008000000
176. [ 0.692108] qcom-pcie 1b500000.pci: Link up
177. [ 0.692299] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
178. [ 0.695218] pci_bus 0000:00: root bus resource [bus 00-ff]
179. [ 0.701360] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0xfe00000-0xfe0ffff])
180. [ 0.706912] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
181. [ 0.716189] pci_bus 0000:00: scanning bus
182. [ 0.723015] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
183. [ 0.727255] pci 0000:00:00.0: supports D1
184. [ 0.733119] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
185. [ 0.737124] pci 0000:00:00.0: PME# disabled
186. [ 0.746509] pci_bus 0000:00: fixups for bus
187. [ 0.746759] PCI: bus0: Fast back to back transfers disabled
188. [ 0.750923] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
189. [ 0.756695] pci_bus 0000:01: scanning bus
190. [ 0.763742] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
191. [ 0.767668] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
192. [ 0.774763] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
193. [ 0.780203] pci 0000:01:00.0: PME# disabled
194. [ 0.790160] pci_bus 0000:01: fixups for bus
195. [ 0.790266] PCI: bus1: Fast back to back transfers disabled
196. [ 0.794321] pci_bus 0000:01: bus scan returning with max=01
197. [ 0.799983] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
198. [ 0.805516] pci_bus 0000:00: bus scan returning with max=ff
199. [ 0.812400] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
200. [ 0.817768] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
201. [ 0.824755] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
202. [ 0.831815] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
203. [ 0.837207] pcieport 0000:00:00.0: assign IRQ: got 46
204. [ 0.844658] pcieport 0000:00:00.0: AER: enabled with IRQ 47
205. [ 0.849087] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
206. [ 0.854312] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100547)
207. [ 0.862736] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
208. [ 0.870452] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10010)
209. [ 0.878771] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0x0)
210. [ 0.886603] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0)
211. [ 0.894066] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
212. [ 0.901785] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0xf0)
213. [ 0.910126] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0x8100800)
214. [ 0.917851] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
215. [ 0.925902] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0)
216. [ 0.933648] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0)
217. [ 0.941376] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0)
218. [ 0.948989] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x40)
219. [ 0.956643] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0)
220. [ 0.964550] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x3012e)
221. [ 0.972694] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator
222. [ 0.980230] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator
223. [ 0.987728] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator
224. [ 0.995620] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
225. [ 1.003021] qcom-pcie 1b700000.pci: Parsing ranges property...
226. [ 1.010069] qcom-pcie 1b700000.pci: IO 0x0031e00000..0x0031e0ffff -> 0x0031e00000
227. [ 1.015771] qcom-pcie 1b700000.pci: MEM 0x002e000000..0x0031dfffff -> 0x002e000000
228. [ 1.252147] qcom-pcie 1b700000.pci: Link up
229. [ 1.252323] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
230. [ 1.255269] pci_bus 0001:00: root bus resource [bus 00-ff]
231. [ 1.261393] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x31e00000-0x31e0ffff])
232. [ 1.266951] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
233. [ 1.276569] pci_bus 0001:00: scanning bus
234. [ 1.283390] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
235. [ 1.287622] pci 0001:00:00.0: supports D1
236. [ 1.293500] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
237. [ 1.297512] pci 0001:00:00.0: PME# disabled
238. [ 1.306807] pci_bus 0001:00: fixups for bus
239. [ 1.307140] PCI: bus0: Fast back to back transfers disabled
240. [ 1.311301] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
241. [ 1.317054] pci_bus 0001:01: scanning bus
242. [ 1.324123] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
243. [ 1.328081] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
244. [ 1.335230] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
245. [ 1.340503] pci 0001:01:00.0: PME# disabled
246. [ 1.350552] pci_bus 0001:01: fixups for bus
247. [ 1.350656] PCI: bus1: Fast back to back transfers disabled
248. [ 1.354702] pci_bus 0001:01: bus scan returning with max=01
249. [ 1.360365] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
250. [ 1.365900] pci_bus 0001:00: bus scan returning with max=ff
251. [ 1.372776] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
252. [ 1.378148] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
253. [ 1.385202] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
254. [ 1.392121] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
255. [ 1.397584] pcieport 0001:00:00.0: assign IRQ: got 48
256. [ 1.405099] pcieport 0001:00:00.0: AER: enabled with IRQ 49
257. [ 1.409398] pcieport 0001:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
258. [ 1.414692] pcieport 0001:00:00.0: saving config space at offset 0x4 (reading 0x100547)
259. [ 1.423126] pcieport 0001:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
260. [ 1.430836] pcieport 0001:00:00.0: saving config space at offset 0xc (reading 0x10010)
261. [ 1.439185] pcieport 0001:00:00.0: saving config space at offset 0x10 (reading 0x0)
262. [ 1.446986] pcieport 0001:00:00.0: saving config space at offset 0x14 (reading 0x0)
263. [ 1.454446] pcieport 0001:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
264. [ 1.462170] pcieport 0001:00:00.0: saving config space at offset 0x1c (reading 0xf0)
265. [ 1.470510] pcieport 0001:00:00.0: saving config space at offset 0x20 (reading 0x2e102e00)
266. [ 1.478236] pcieport 0001:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
267. [ 1.486285] pcieport 0001:00:00.0: saving config space at offset 0x28 (reading 0x0)
268. [ 1.494116] pcieport 0001:00:00.0: saving config space at offset 0x2c (reading 0x0)
269. [ 1.501853] pcieport 0001:00:00.0: saving config space at offset 0x30 (reading 0x0)
270. [ 1.509467] pcieport 0001:00:00.0: saving config space at offset 0x34 (reading 0x40)
271. [ 1.517120] pcieport 0001:00:00.0: saving config space at offset 0x38 (reading 0x0)
272. [ 1.525087] pcieport 0001:00:00.0: saving config space at offset 0x3c (reading 0x30130)
273. [ 1.535328] L2 @ QSB rate. Forcing new rate.
274. [ 1.540584] L2 @ 384000 KHz
275. [ 1.545168] CPU0 @ 800000 KHz
276. [ 1.547404] CPU1 @ QSB rate. Forcing new rate.
277. [ 1.550649] CPU1 @ 384000 KHz
278. [ 1.559175] gsbi 12480000.gsbi: GSBI port protocol: 4 crci: 0
279. [ 1.561775] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
280. [ 1.565846] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
281. [ 1.571483] gsbi 16600000.gsbi: GSBI port protocol: 2 crci: 0
282. [ 1.577768] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
283. [ 1.583810] msm_serial 12490000.serial: msm_serial: detected port #1
284. [ 1.587660] msm_serial 12490000.serial: uartclk = 25000000
285. [ 1.593915] 12490000.serial: ttyMSM1 at MMIO 0x12490000 (irq = 50, base_baud = 1562500) is a MSM
286. [ 1.599836] msm_serial 16340000.serial: msm_serial: detected port #0
287. [ 1.608213] msm_serial 16340000.serial: uartclk = 7372800
288. [ 1.614477] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 51, base_baud = 46080▒[ 1.628367] printk: console [ttyMSM0] enabled
289. [ 1.628367] printk: console [ttyMSM0] enabled
290. [ 1.631705] printk: bootconsole [msm_serial_dm0] disabled
291. [ 1.631705] printk: bootconsole [msm_serial_dm0] disabled
292. [ 1.641835] msm_serial: driver initialized
293. [ 1.652719] loop: module loaded
294. [ 1.654475] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xac
295. [ 1.654678] nand: Micron MT29F4G08ABBDAH4
296. [ 1.661401] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
297. [ 1.665324] 1 fixed-partitions partitions found on MTD device qcom_nand.0
298. [ 1.672649] Creating 1 MTD partitions on "qcom_nand.0":
299. [ 1.679643] 0x000000000000-0x000020000000 : "rootfs"
300. [ 1.692753] random: fast init done
301. [ 2.167172] random: crng init done
302. [ 3.017883] mtd: device 0 (rootfs) set to be root filesystem
303. [ 3.019079] mtdsplit: no squashfs found in "rootfs"
304. [ 3.027054] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
305. [ 3.031526] spi-nor spi0.0: mx25u3235f (4096 Kbytes)
306. [ 3.034711] 13 fixed-partitions partitions found on MTD device spi0.0
307. [ 3.039683] Creating 13 MTD partitions on "spi0.0":
308. [ 3.046006] 0x000000000000-0x000000010000 : "0:SBL1"
309. [ 3.051566] 0x000000010000-0x000000030000 : "0:MIBIB"
310. [ 3.056811] 0x000000030000-0x000000060000 : "0:SBL2"
311. [ 3.061585] 0x000000060000-0x000000090000 : "0:SBL3"
312. [ 3.066678] 0x000000090000-0x0000000a0000 : "0:DDRCONFIG"
313. [ 3.071563] 0x0000000a0000-0x0000000b0000 : "0:APPSBLENV"
314. [ 3.076926] 0x0000000b0000-0x0000000c0000 : "0:ART"
315. [ 3.082320] 0x0000000c0000-0x0000000f0000 : "0:TZ"
316. [ 3.087100] 0x0000000f0000-0x000000110000 : "0:RPM"
317. [ 3.091792] 0x000000110000-0x0000001a0000 : "0:APPSBL"
318. [ 3.096722] 0x0000001a0000-0x000000200000 : "0:stat_cfg"
319. [ 3.101752] 0x000000200000-0x000000300000 : "0:dyn_cfg"
320. [ 3.107359] 0x000000300000-0x000000400000 : "0:dyn_cfg_backup"
321. [ 3.227339] libphy: Fixed MDIO Bus: probed
322. [ 3.229106] libphy: ipq8064_mdio_bus: probed
323. [ 3.242287] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
324. [ 3.242348] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
325. [ 3.248909] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
326. [ 3.255830] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
327. [ 3.261371] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
328. [ 3.268923] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
329. [ 3.274643] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
330. [ 3.282518] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
331. [ 3.290338] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
332. [ 3.296178] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
333. [ 3.303462] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
334. [ 3.310332] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
335. [ 3.317861] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
336. [ 3.324912] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
337. [ 3.372457] libphy: stmmac: probed
338. [ 3.375354] ipq806x-gmac-dwmac 37600000.ethernet: IRQ eth_wake_irq not found
339. [ 3.375421] ipq806x-gmac-dwmac 37600000.ethernet: IRQ eth_lpi not found
340. [ 3.382324] ipq806x-gmac-dwmac 37600000.ethernet: PTP uses main clock
341. [ 3.389275] ipq806x-gmac-dwmac 37600000.ethernet: User ID: 0x10, Synopsys ID: 0x37
342. [ 3.395032] ipq806x-gmac-dwmac 37600000.ethernet: DWMAC1000
343. [ 3.402386] ipq806x-gmac-dwmac 37600000.ethernet: DMA HW capability register supported
344. [ 3.408323] ipq806x-gmac-dwmac 37600000.ethernet: RX Checksum Offload Engine supported
345. [ 3.416035] ipq806x-gmac-dwmac 37600000.ethernet: COE Type 2
346. [ 3.423823] ipq806x-gmac-dwmac 37600000.ethernet: TX Checksum insertion supported
347. [ 3.429730] ipq806x-gmac-dwmac 37600000.ethernet: Wake-Up On Lan supported
348. [ 3.437104] ipq806x-gmac-dwmac 37600000.ethernet: Enhanced/Alternate descriptors
349. [ 3.443792] ipq806x-gmac-dwmac 37600000.ethernet: Enabled extended descriptors
350. [ 3.451444] ipq806x-gmac-dwmac 37600000.ethernet: Ring mode enabled
351. [ 3.458471] ipq806x-gmac-dwmac 37600000.ethernet: Enable RX Mitigation via HW Watchdog Timer
352. [ 3.505896] libphy: stmmac: probed
353. [ 3.509013] i2c /dev entries driver
354. [ 3.509726] i2c_qup 16680000.i2c: using default clock-frequency 100000
355. [ 3.519040] sdhci: Secure Digital Host Controller Interface driver
356. [ 3.519080] sdhci: Copyright(c) Pierre Ossman
357. [ 3.524348] sdhci-pltfm: SDHCI platform and OF driver helper
358. [ 3.531565] NET: Registered protocol family 10
359. [ 3.536003] Segment Routing with IPv6
360. [ 3.538848] NET: Registered protocol family 17
361. [ 3.542784] 8021q: 802.1Q VLAN Support v1.8
362. [ 3.547047] Registering SWP/SWPB emulation handler
363. [ 3.579638] qcom_rpm 108000.rpm: RPM firmware 3.0.16777375
364. [ 3.594088] s1a: Bringing 0uV into 1050000-1050000uV
365. [ 3.594397] s1a: supplied by regulator-dummy
366. [ 3.598358] s1b: Bringing 0uV into 1050000-1050000uV
367. [ 3.602629] s1b: supplied by regulator-dummy
368. [ 3.607523] s2a: Bringing 0uV into 800000-800000uV
369. [ 3.611809] s2a: supplied by regulator-dummy
370. [ 3.616403] s2b: Bringing 0uV into 800000-800000uV
371. [ 3.620858] s2b: supplied by regulator-dummy
372. [ 3.634940] thermal thermal_zone0: failed to read out thermal zone (-110)
373. [ 3.648480] ubi0: attaching mtd0
374. [ 11.892068] ubi0: scanning is finished
375. [ 11.915392] ubi0: attached mtd0 (name "rootfs", size 512 MiB)
376. [ 11.915416] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
377. [ 11.920109] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
378. [ 11.926942] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
379. [ 11.933738] ubi0: good PEBs: 4096, bad PEBs: 0, corrupted PEBs: 0
380. [ 11.940593] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
381. [ 11.946834] ubi0: max/mean erase counter: 29/5, WL threshold: 4096, image sequence number: 1062653683
382. [ 11.953882] ubi0: available PEBs: 0, total reserved PEBs: 4096, PEBs reserved for bad PEB handling: 80
383. [ 11.963330] ubi0: background thread "ubi_bgt0d" started, PID 153
384. [ 11.974801] block ubiblock0_1: created from ubi0:1(rootfs)
385. [ 11.979655] UB▒[ 11.994443] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
386. [ 11.995623] Freeing unused kernel memory: 1024K
387. [ 12.035586] Run /sbin/init as init process
388. [ 12.035619] with arguments:
389. [ 12.038574] /sbin/init
390. [ 12.041612] with environment:
391. [ 12.044216] HOME=/
392. [ 12.047356] TERM=linux
393. [ 12.726285] init: Console is alive
394. [ 12.726473] init: - watchdog -
395. [ 12.728666] init: Watchdog has previously reset the system
396. [ 13.740644] kmodloader: loading kernel modules from /etc/modules-boot.d/*
397. [ 13.768720] pps_ldisc: PPS line discipline registered
398. [ 13.770108] genirq: irq_chip msmgpio did not update eff. affinity mask of irq 54
399. [ 13.780844] tpm tpm0: starting up the TPM manually
400. [ 13.863392] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
401. [ 13.866988] init: - preinit -
402. [ 15.092077] ipq806x-gmac-dwmac 37400000.ethernet ethtmp: renamed from eth0
403. [ 15.143161] ipq806x-gmac-dwmac 37600000.ethernet eth0: renamed from eth1
404. [ 15.192855] ipq806x-gmac-dwmac 37400000.ethernet eth1: renamed from ethtmp
405. [ 15.609776] ipq806x-gmac-dwmac 37600000.ethernet eth0: PHY [37000000.mdio-mii:02] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
406. [ 15.611283] dwmac1000: Master AXI performs any burst length
407. [ 15.620928] ipq806x-gmac-dwmac 37600000.ethernet eth0: No Safety Features support found
408. [ 15.636241] ipq806x-gmac-dwmac 37600000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
409. [ 15.636599] ipq806x-gmac-dwmac 37600000.ethernet eth0: registered PTP clock
410. [ 15.645760] ipq806x-gmac-dwmac 37600000.ethernet eth0: configuring for phy/sgmii link mode
411. Press the [f] key and hit [enter] to enter failsafe mode
412. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
413. [ 19.810328] ipq806x-gmac-dwmac 37600000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
414. [ 19.810384] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
415. [ 19.917188] UBIFS (ubi0:2): default file-system created
416. [ 19.919307] UBIFS (ubi0:2): Mounting in unauthenticated mode
417. [ 19.925140] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 234
418. [ 20.125201] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
419. [ 20.125265] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
420. [ 20.132046] UBIFS (ubi0:2): FS size: 492412928 bytes (469 MiB, 3878 LEBs), journal size 24633344 bytes (23 MiB, 194 LEBs)
421. [ 20.142050] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
422. [ 20.152957] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 5ECB64D4-59DC-44AD-97E5-098FEEC9E054, small LPT model
423. [ 20.164399] mount_root: overlay filesystem has not been fully initialized yet
424. [ 20.171349] mount_root: switching to ubifs overlay
425. [ 20.198404] urandom-seed: Seed file not found (/etc/urandom.seed)
426. [ 20.418331] ipq806x-gmac-dwmac 37600000.ethernet eth0: Link is Down
427. [ 20.429299] procd: - early -
428. [ 20.429554] procd: - watchdog -
429. [ 20.431471] procd: Watchdog has previously reset the system
430. [ 21.051923] procd: - watchdog -
431. [ 21.052179] procd: Watchdog has previously reset the system
432. [ 21.094507] procd: - ubus -
433. [ 21.348783] procd: - init -
434. Please press Enter to activate this console.
435. [ 21.976951] urngd: v1.0.2 started.
436. [ 22.020490] kmodloader: loading kernel modules from /etc/modules.d/*
437. [ 22.079184] hid: raw HID events driver (C) Jiri Kosina
438. [ 22.080321] GACT probability on
439. [ 22.084002] Mirror/redirect action on
440. [ 22.092125] u32 classifier
441. [ 22.092147] input device check on
442. [ 22.093715] Actions configured
443. [ 22.124099] Bluetooth: Core ver 2.22
444. [ 22.124256] NET: Registered protocol family 31
445. [ 22.126901] Bluetooth: HCI device and connection manager initialized
446. [ 22.131016] Bluetooth: HCI socket layer initialized
447. [ 22.137582] Bluetooth: L2CAP socket layer initialized
448. [ 22.142140] Bluetooth: SCO socket layer initialized
449. [ 22.149084] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
450. [ 22.152008] Bluetooth: BNEP filters: protocol multicast
451. [ 22.157692] Bluetooth: BNEP socket layer initialized
452. [ 22.167285] usbcore: registered new interface driver btusb
453. [ 22.169974] Loading modules backported from Linux version v5.15.8-0-g43e577d7a2cb
454. [ 22.173016] Backport generated by backports.git v5.15.8-1-0-g83f664bb
455. [ 22.181676] Bluetooth: HCI UART driver ver 2.3
456. [ 22.187061] Bluetooth: HCI UART protocol H4 registered
457. [ 22.191326] Bluetooth: HCI UART protocol BCSP registered
458. [ 22.196543] Bluetooth: HCI UART protocol ATH3K registered
459. [ 22.203507] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
460. [ 22.207339] Bluetooth: HIDP socket layer initialized
461. [ 22.233875] Bluetooth: RFCOMM TTY layer initialized
462. [ 22.233926] Bluetooth: RFCOMM socket layer initialized
463. [ 22.237704] Bluetooth: RFCOMM ver 1.11
464. [ 22.271166] xt_time: kernel timezone is -0000
465. [ 22.271747] usbcore: registered new interface driver ath3k
466. [ 22.489845] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
467. [ 22.489876] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <[email protected]>. All Rights Reserved.
468. [ 22.522310] ath10k_pci 0000:01:00.0: assign IRQ: got 46
469. [ 22.522358] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x40.
470. [ 22.527113] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
471. [ 22.534400] ath10k_pci 0000:01:00.0: enabling bus mastering
472. [ 22.540986] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
473. [ 23.943165] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
474. [ 23.943230] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
475. [ 23.956880] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9980-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 b36a12bf
476. [ 24.112485] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:6 crc32 08fa09f2
477. [ 25.261483] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
478. [ 25.261523] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
479. [ 25.342248] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
480. [ 25.343007] ath10k_pci 0000:01:00.0: wmi print 'free: 31080 iram: 23028 sram: 9596'
481. [ 26.106649] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
482. [ 26.197202] ath: EEPROM regdomain sanitized
483. [ 26.197249] ath: EEPROM regdomain: 0x64
484. [ 26.200205] ath: EEPROM indicates we should expect a direct regpair map
485. [ 26.204041] ath: Country alpha2 being used: 00
486. [ 26.210741] ath: Regpair used: 0x64
487. [ 26.221218] ath10k_pci 0001:01:00.0: assign IRQ: got 48
488. [ 26.221292] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x40.
489. [ 26.227285] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
490. [ 26.233357] ath10k_pci 0001:01:00.0: enabling bus mastering
491. [ 26.254974] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
492. [ 27.598991] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
493. [ 27.599031] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
494. [ 27.609413] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 b36a12bf
495. [ 27.679899] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:4 crc32 08fa09f2
496. [ 28.829458] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
497. [ 28.829499] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
498. [ 28.910121] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
499. [ 28.910884] ath10k_pci 0001:01:00.0: wmi print 'free: 31080 iram: 23028 sram: 9596'
500. [ 29.183437] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
501. [ 29.277236] ath: EEPROM regdomain sanitized
502. [ 29.277286] ath: EEPROM regdomain: 0x64
503. [ 29.280242] ath: EEPROM indicates we should expect a direct regpair map
504. [ 29.284080] ath: Country alpha2 being used: 00
505. [ 29.290786] ath: Regpair used: 0x64
506. [ 29.308560] kmodloader: done loading kernel modules from /etc/modules.d/*
507. [ 32.662792] [xx_custom] INFO: Applying custom default configuration
508. [ 32.663368] [xx_custom] INFO: Setting hostname based on MAC address
509. [ 32.688750] [xx_custom] INFO: Applying network configuration
510. [ 32.739528] [xx_custom] PASSWD: Setting root password to 9035ef223d4143c3fd3ae242
511. [ 32.825640] [xx_custom] INFO: Finished applying custom default configuration.
512. [ 40.249667] ipq806x-gmac-dwmac 37600000.ethernet eth0: PHY [37000000.mdio-mii:02] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
513. [ 40.250298] dwmac1000: Master AXI performs any burst length
514. [ 40.260786] ipq806x-gmac-dwmac 37600000.ethernet eth0: No Safety Features support found
515. [ 40.276029] ipq806x-gmac-dwmac 37600000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
516. [ 40.276162] ipq806x-gmac-dwmac 37600000.ethernet eth0: registered PTP clock
517. [ 40.283880] ipq806x-gmac-dwmac 37600000.ethernet eth0: configuring for phy/sgmii link mode
518. [ 40.293838] br-lan: port 1(eth0) entered blocking state
519. [ 40.299221] br-lan: port 1(eth0) entered disabled state
520. [ 40.304459] device eth0 entered promiscuous mode
521. [ 40.401524] ipq806x-gmac-dwmac 37400000.ethernet eth1: PHY [37000000.mdio-mii:01] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
522. [ 40.402166] dwmac1000: Master AXI performs any burst length
523. [ 40.412639] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
524. [ 40.427907] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
525. [ 40.428040] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
526. [ 40.436303] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for phy/sgmii link mode
527. [ 40.445911] br-lan: port 2(eth1) entered blocking state
528. [ 40.450943] br-lan: port 2(eth1) entered disabled state
529. [ 40.456416] device eth1 entered promiscuous mode
530. [ 40.461384] br-lan: port 2(eth1) entered blocking state
531. [ 40.466292] br-lan: port 2(eth1) entered forwarding state
532. [ 40.471189] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
533. [ 41.288486] br-lan: port 2(eth1) entered disabled state
534. [ 42.394221] device eth0 left promiscuous mode
535. [ 42.394290] br-lan: port 1(eth0) entered disabled state
536. [ 42.419295] device eth1 left promiscuous mode
537. [ 42.419370] br-lan: port 2(eth1) entered disabled state
538. [ 42.694699] ipq806x-gmac-dwmac 37600000.ethernet eth0: PHY [37000000.mdio-mii:02] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
539. [ 42.695320] dwmac1000: Master AXI performs any burst length
540. [ 42.705766] ipq806x-gmac-dwmac 37600000.ethernet eth0: No Safety Features support found
541. [ 42.720985] ipq806x-gmac-dwmac 37600000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
542. [ 42.721153] ipq806x-gmac-dwmac 37600000.ethernet eth0: registered PTP clock
543. [ 42.729068] ipq806x-gmac-dwmac 37600000.ethernet eth0: configuring for phy/sgmii link mode
544. [ 42.743294] br-lan: port 1(eth0) entered blocking state
545. [ 42.744025] br-lan: port 1(eth0) entered disabled state
546. [ 42.749483] device eth0 entered promiscuous mode
547. [ 42.839932] ipq806x-gmac-dwmac 37400000.ethernet eth1: PHY [37000000.mdio-mii:01] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
548. [ 42.840554] dwmac1000: Master AXI performs any burst length
549. [ 42.851006] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
550. [ 42.866306] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
551. [ 42.866441] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
552. [ 42.874164] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for phy/sgmii link mode
553. [ 42.884218] br-lan: port 2(eth1) entered blocking state
554. [ 42.889450] br-lan: port 2(eth1) entered disabled state
555. [ 42.894720] device eth1 entered promiscuous mode
556. [ 45.895280] ipq806x-gmac-dwmac 37600000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
557. [ 45.895364] br-lan: port 1(eth0) entered blocking state
558. [ 45.903146] br-lan: port 1(eth0) entered forwarding state
559. [ 45.908683] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
560. ​
561. ​
562. ​
563. BusyBox v1.35.0 (2022-01-17 06:44:52 UTC) built-in shell (ash)
564. ​
565. _______ ________ __
566. | |.-----.-----.-----.| | | |.----.| |_
567. | - || _ | -__| || | | || _|| _|
568. |_______|| __|_____|__|__||________||__| |____|
569. |__| W I R E L E S S F R E E D O M
570. -----------------------------------------------------
571. OpenWrt apx530, r18592-6e02b3c482
572. -----------------------------------------------------
573. root@apx530-346182 / #