U-Boot 1.1.3 (Apr 24 2015 - 09:27:12) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fac000 ****************************** Software System Reset Occurred ****************************** spi_wait_nsec: 42 spi device id: ef 40 18 0 0 (40180000) find flash: W25Q128BV raspi_read: from:30000 len:1000 .raspi_read: from:30000 len:1000 .============================================ Ralink UBoot Version: 4.0.1.0 -------------------------------------------- ASIC 5350_MP (Port5<->None) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: SDRAM DRAM_SIZE: 256 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 32 MBytes Flash component: SPI Flash Date:Apr 24 2015 Time:09:27:12 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 360 MHZ #### estimate memory size =32 Mbytes Hold GPIO 0 high for 3 seconds then release to trigger webpage to load image GPIO 0 is low Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 8: Start Web Server to load system code. 9: Load Boot Loader code then write to Flash via TFTP. You chose 8 0 raspi_read: from:40028 len:6 . NetTxPacket = 0x81FE6500 KSEG1ADDR(NetTxPacket) = 0xA1FE6500 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) Waitting for RX_DMA_BUSY status Start... done Header Payload scatter function is Disable !! ETH_STATE_ACTIVE!! Trying Eth0 (10/100-M) ETH_STATE_ACTIVE!! HTTP server is starting at IP : 172.21.10.31 HTTP server is ready! Request for: / opening file /index.html found file /style.css found file /404.html found file /index.html Request for: /style.css opening file /style.css found file /style.css Request for: /uboot.html opening file /uboot.html found file /style.css found file /404.html found file /index.html found file /flashing.html found file /fail.html web Data will be downloaded at 0x80300000 in RAM Upgrade type: firmware Upload file size: 5505855 bytes Loading: ####################################### ####################################### ####################################### ####################################### ####################################### ####################################### ####################################### ####################################### ####################################### ###############################all data collected upload size: 0x 54037F, expected size: 0x 54033F upload good ask for file /flashing.html opening file /flashing.html found file /style.css found file /404.html found file /index.html found file /flashing.html state reset state reset successful sending result page Request for: / opening file /index.html found file /style.css found file /404.html found file /index.html Request for: /style.css opening file /style.css found file /style.css HTTP upload is done! Upgrading... **************************** * FIRMWARE UPGRADING * * DO NOT POWER OFF DEVICE! * **************************** Executing: erase linux; cp.weblinux Erase linux kernel block !! From 0x50000 length 0xFB0000 raspi_erase: offs:50000 len:fb0000 ........................................................................................................................................................................................................................................................... Copy linux image from web[5505855 byte] to SPI Flash[0x00050000].... raspi_write: to:50000 len:54033f ..................................................................................... HTTP ugrade is done! Rebooting... U-Boot 1.1.3 (Apr 24 2015 - 09:27:12) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fac000 ****************************** Software System Reset Occurred ****************************** spi_wait_nsec: 42 spi device id: ef 40 18 0 0 (40180000) find flash: W25Q128BV raspi_read: from:30000 len:1000 .raspi_read: from:30000 len:1000 .============================================ Ralink UBoot Version: 4.0.1.0 -------------------------------------------- ASIC 5350_MP (Port5<->None) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: SDRAM DRAM_SIZE: 256 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 32 MBytes Flash component: SPI Flash Date:Apr 24 2015 Time:09:27:12 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 360 MHZ #### estimate memory size =32 Mbytes Hold GPIO 0 high for 3 seconds then release to trigger webpage to load image GPIO 0 is low Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 8: Start Web Server to load system code. 9: Load Boot Loader code then write to Flash via TFTP. GPIO 0 went high 0 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 . Image Name: MIPS OpenWrt Linux-5.10.111 Created: 2022-04-20 16:14:08 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2200126 Bytes = 2.1 MB Load Address: 80000000 Entry Point: 80000000 raspi_read: from:50040 len:21923e .................................. Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 32 Starting kernel ... [ 0.000000] Linux version 5.10.111 (aholmes@astraea-lnx) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19508-0d2d52df69e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Wed Apr 20 16:14:08 2022 [ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc) [ 0.000000] MIPS: machine is VoCore (16M) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 8120 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.000000] Writing ErrCtl register=00073a30 [ 0.000000] Readback ErrCtl register=00073a30 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 23912K/32768K available (5339K kernel code, 605K rwdata, 1092K rodata, 1212K init, 210K bss, 8856K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x3b8/0x5a8 with crng_init=0 [ 0.000000] CPU Clock: 360MHz [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns [ 0.000017] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns [ 0.015757] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080) [ 0.098047] pid_max: default: 32768 minimum: 301 [ 0.107562] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.122063] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.142705] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.165335] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.184923] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.198623] pinctrl core: initialized pinctrl subsystem [ 0.213401] NET: Registered protocol family 16 [ 0.372804] rt2880_gpio 10000600.gpio: registering 22 gpios [ 0.384049] rt2880_gpio 10000600.gpio: registering 22 irq handlers [ 0.397141] rt2880_gpio 10000660.gpio: registering 6 gpios [ 0.408138] rt2880_gpio 10000660.gpio: registering 6 irq handlers [ 0.442714] clocksource: Switched to clocksource MIPS [ 0.455614] NET: Registered protocol family 2 [ 0.464732] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.480870] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.497694] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.512944] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.526922] TCP: Hash tables configured (established 1024 bind 1024) [ 0.539946] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.553030] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.567464] NET: Registered protocol family 1 [ 0.587963] rt-timer 10000100.timer: maximum frequency is 3662Hz [ 0.609124] workingset: timestamp_bits=14 max_order=13 bucket_order=0 [ 0.631621] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.643242] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.665221] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.689218] gpio-export gpio-export: 17 gpio(s) exported [ 0.700499] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.719404] printk: console [ttyS0] disabled [ 0.728106] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103 [ 0.747875] printk: console [ttyS0] enabled [ 0.747875] printk: console [ttyS0] enabled [ 0.764441] printk: bootconsole [early0] disabled [ 0.764441] printk: bootconsole [early0] disabled [ 0.840949] spi spi0.0: force spi mode3 [ 0.851295] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 0.861115] 4 fixed-partitions partitions found on MTD device spi0.0 [ 0.873918] Creating 4 MTD partitions on "spi0.0": [ 0.883568] 0x000000000000-0x000000030000 : "uboot" [ 0.898125] 0x000000030000-0x000000040000 : "uboot-env" [ 0.911167] 0x000000040000-0x000000050000 : "factory" [ 0.928522] 0x000000050000-0x000001000000 : "firmware" [ 0.941631] 2 uimage-fw partitions found on MTD device firmware [ 0.953642] Creating 2 MTD partitions on "firmware": [ 0.963644] 0x000000000000-0x00000021927e : "kernel" [ 0.973610] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only [ 0.997024] 0x00000021927e-0x000000fb0000 : "rootfs" [ 1.007140] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only [ 1.030071] mtd: device 5 (rootfs) set to be root filesystem [ 1.041795] 1 squashfs-split partitions found on MTD device rootfs [ 1.054303] 0x00000053a000-0x000000fb0000 : "rootfs_data" [ 1.095858] spi spi1.0: force spi mode3 [ 1.147654] rt3050-esw 10110000.esw: mediatek esw at 0xb0110000, irq 25 initialized [ 1.164723] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 1.182449] rt2880_wdt 10000120.watchdog: Initialized [ 1.195355] NET: Registered protocol family 10 [ 1.216290] Segment Routing with IPv6 [ 1.224024] NET: Registered protocol family 17 [ 1.233254] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.259236] 8021q: 802.1Q VLAN Support v1.8 [ 1.294261] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 1.320941] Freeing unused kernel memory: 1212K [ 1.330077] This architecture does not have kernel memory protection. [ 1.343002] Run /sbin/init as init process [ 2.712730] random: fast init done [ 2.754573] rt3050-esw 10110000.esw: port 4 link up [ 3.080748] init: Console is alive [ 3.088787] init: - watchdog - [ 5.995063] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 6.318830] usbcore: registered new interface driver usbfs [ 6.330217] usbcore: registered new interface driver hub [ 6.341201] usbcore: registered new device driver usb [ 6.362165] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 6.387834] init: - preinit - [ 10.160543] random: jshn: uninitialized urandom read (4 bytes read) [ 10.639589] random: jshn: uninitialized urandom read (4 bytes read) [ 10.851172] random: jshn: uninitialized urandom read (4 bytes read) [ 11.187184] urandom_read: 1 callbacks suppressed [ 11.187203] random: jshn: uninitialized urandom read (4 bytes read) [ 12.087562] rt3050-esw 10110000.esw: port 4 link down [ 12.643341] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 13.710958] rt3050-esw 10110000.esw: port 4 link up [ 13.720954] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 13.749877] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 17.373058] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 17.396927] urandom-seed: Seed file not found (/etc/urandom.seed) [ 17.842611] procd: - early - [ 17.849350] procd: - watchdog - [ 19.168908] procd: - watchdog - [ 19.177024] procd: - ubus - [ 19.525811] random: ubusd: uninitialized urandom read (4 bytes read) [ 19.544280] random: ubusd: uninitialized urandom read (4 bytes read) [ 19.558493] random: ubusd: uninitialized urandom read (4 bytes read) [ 19.601552] procd: - init - Please press Enter to activate this console. [ 22.546631] kmodloader: loading kernel modules from /etc/modules.d/* [ 23.535530] i2c /dev entries driver [ 23.557959] i2c-ralink 10000900.i2c: clock 100KHz, re-start support [ 23.612417] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace [ 23.627722] Backport generated by backports.git v5.15.33-1-0-g183c4ab2 [ 23.820492] urngd: v1.0.2 started. [ 24.609808] PPP generic driver version 2.4.2 [ 24.638002] NET: Registered protocol family 24 [ 24.799966] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory" [ 24.814595] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected [ 24.830190] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected [ 25.133496] kmodloader: done loading kernel modules from /etc/modules.d/* [ 25.631191] random: crng init done [ 25.638165] random: 1 urandom warning(s) missed due to ratelimiting [ 34.637180] [xx_custom] INFO: Timezone sanity check enabled: TIME_ZONE=Australia/Melbourne BOOT_TZ=UTC [ 34.672985] [xx_custom] WARNING: Timezone does not match, continuing [ 34.703138] [xx_custom] WARN: Unable to find eth0.1, will use generic hostname [ 34.734317] [xx_custom] INFO: Setting hostname to vocore-16m [ 34.785717] [xx_custom] INFO: Using fixed root password: send4help [ 34.871774] [xx_custom] INFO: Applying LAN configuration [ 34.939403] [xx_custom] INFO: Applying DHCP configuration [ 35.014879] [xx_custom] INFO: Applying NTP and timezone configuration [ 35.084979] [xx_custom] INFO: Applying miscellaneous settings [ 35.158617] [xx_custom] INFO: Setting system.autoconf=done [ 35.209210] [xx_custom] INFO: Finished applying custom default configuration, please check log for errors. [ 73.897657] rt3050-esw 10110000.esw: port 4 link down [ 75.537440] rt3050-esw 10110000.esw: port 4 link up [ 80.121147] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 80.164312] jffs2_build_filesystem(): unlocking the mtd device... [ 80.164339] done. [ 80.180661] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 92.473870] br-lan: port 1(eth0.1) entered blocking state [ 92.499743] br-lan: port 1(eth0.1) entered disabled state [ 92.511367] device eth0.1 entered promiscuous mode [ 92.521097] device eth0 entered promiscuous mode [ 92.914835] br-lan: port 1(eth0.1) entered blocking state [ 92.925765] br-lan: port 1(eth0.1) entered forwarding state [ 93.443717] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 339.179113] done. [ 339.183131] jffs2: notice: (1509) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 339.559945] overlayfs: upper fs does not support tmpfile. BusyBox v1.35.0 (2022-04-20 16:14:08 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r19508-0d2d52df69e ----------------------------------------------------- root@vocore-16m / # free total used free shared buff/cache available Mem: 25124 13120 5920 120 6084 8620 Swap: 0 0 0 root@vocore-16m / # oof /bin/ash: oof: not found root@vocore-16m / # cat /proc/meminfo MemTotal: 25124 kB MemFree: 5916 kB MemAvailable: 8620 kB Buffers: 0 kB Cached: 5192 kB SwapCached: 0 kB Active: 3712 kB Inactive: 3048 kB Active(anon): 156 kB Inactive(anon): 1532 kB Active(file): 3556 kB Inactive(file): 1516 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 1576 kB Mapped: 2528 kB Shmem: 120 kB KReclaimable: 896 kB Slab: 6356 kB SReclaimable: 896 kB SUnreclaim: 5460 kB KernelStack: 336 kB PageTables: 336 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 12560 kB Committed_AS: 11276 kB VmallocTotal: 1048372 kB VmallocUsed: 1376 kB VmallocChunk: 0 kB Percpu: 96 kB root@vocore-16m / # df -h Filesystem Size Used Available Use% Mounted on /dev/root 3.3M 3.3M 0 100% /rom tmpfs 12.3M 64.0K 12.2M 1% /tmp tmpfs 12.3M 56.0K 12.2M 0% /tmp/root tmpfs 512.0K 0 512.0K 0% /dev /dev/mtdblock6 10.5M 536.0K 9.9M 5% /overlay overlayfs:/overlay 10.5M 536.0K 9.9M 5% / root@vocore-16m / # free -m total used free shared buff/cache available Mem: 25124 13120 5912 120 6092 8616 Swap: 0 0 0 root@vocore-16m / # dmesg [ 0.000000] Linux version 5.10.111 (aholmes@astraea-lnx) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19508-0d2d52df69e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Wed Apr 20 16:14:08 2022 [ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc) [ 0.000000] MIPS: machine is VoCore (16M) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff] [ 0.000000] On node 0 totalpages: 8192 [ 0.000000] Normal zone: 72 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 8192 pages, LIFO batch:0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 8120 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.000000] Writing ErrCtl register=00073a30 [ 0.000000] Readback ErrCtl register=00073a30 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 23912K/32768K available (5339K kernel code, 605K rwdata, 1092K rodata, 1212K init, 210K bss, 8856K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x3b8/0x5a8 with crng_init=0 [ 0.000000] CPU Clock: 360MHz [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns [ 0.000017] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns [ 0.015757] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080) [ 0.098047] pid_max: default: 32768 minimum: 301 [ 0.107562] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.122063] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.142705] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.165335] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.184923] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.198623] pinctrl core: initialized pinctrl subsystem [ 0.213401] NET: Registered protocol family 16 [ 0.372804] rt2880_gpio 10000600.gpio: registering 22 gpios [ 0.384049] rt2880_gpio 10000600.gpio: registering 22 irq handlers [ 0.397141] rt2880_gpio 10000660.gpio: registering 6 gpios [ 0.408138] rt2880_gpio 10000660.gpio: registering 6 irq handlers [ 0.442714] clocksource: Switched to clocksource MIPS [ 0.455614] NET: Registered protocol family 2 [ 0.464732] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.480870] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.497694] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.512944] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.526922] TCP: Hash tables configured (established 1024 bind 1024) [ 0.539946] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.553030] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.567464] NET: Registered protocol family 1 [ 0.587963] rt-timer 10000100.timer: maximum frequency is 3662Hz [ 0.609124] workingset: timestamp_bits=14 max_order=13 bucket_order=0 [ 0.631621] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.643242] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.665221] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.689218] gpio-export gpio-export: 17 gpio(s) exported [ 0.700499] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.719404] printk: console [ttyS0] disabled [ 0.728106] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103 [ 0.747875] printk: console [ttyS0] enabled [ 0.764441] printk: bootconsole [early0] disabled [ 0.840949] spi spi0.0: force spi mode3 [ 0.851295] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 0.861115] 4 fixed-partitions partitions found on MTD device spi0.0 [ 0.873918] Creating 4 MTD partitions on "spi0.0": [ 0.883568] 0x000000000000-0x000000030000 : "uboot" [ 0.898125] 0x000000030000-0x000000040000 : "uboot-env" [ 0.911167] 0x000000040000-0x000000050000 : "factory" [ 0.928522] 0x000000050000-0x000001000000 : "firmware" [ 0.941631] 2 uimage-fw partitions found on MTD device firmware [ 0.953642] Creating 2 MTD partitions on "firmware": [ 0.963644] 0x000000000000-0x00000021927e : "kernel" [ 0.973610] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only [ 0.997024] 0x00000021927e-0x000000fb0000 : "rootfs" [ 1.007140] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only [ 1.030071] mtd: device 5 (rootfs) set to be root filesystem [ 1.041795] 1 squashfs-split partitions found on MTD device rootfs [ 1.054303] 0x00000053a000-0x000000fb0000 : "rootfs_data" [ 1.095858] spi spi1.0: force spi mode3 [ 1.147654] rt3050-esw 10110000.esw: mediatek esw at 0xb0110000, irq 25 initialized [ 1.164723] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 1.182449] rt2880_wdt 10000120.watchdog: Initialized [ 1.195355] NET: Registered protocol family 10 [ 1.216290] Segment Routing with IPv6 [ 1.224024] NET: Registered protocol family 17 [ 1.233254] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.259236] 8021q: 802.1Q VLAN Support v1.8 [ 1.294261] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 1.320941] Freeing unused kernel memory: 1212K [ 1.330077] This architecture does not have kernel memory protection. [ 1.343002] Run /sbin/init as init process [ 1.351167] with arguments: [ 1.351175] /sbin/init [ 1.351183] with environment: [ 1.351192] HOME=/ [ 1.351200] TERM=linux [ 2.712730] random: fast init done [ 2.754573] rt3050-esw 10110000.esw: port 4 link up [ 3.080748] init: Console is alive [ 3.088787] init: - watchdog - [ 5.995063] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 6.318830] usbcore: registered new interface driver usbfs [ 6.330217] usbcore: registered new interface driver hub [ 6.341201] usbcore: registered new device driver usb [ 6.362165] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 6.387834] init: - preinit - [ 10.160543] random: jshn: uninitialized urandom read (4 bytes read) [ 10.639589] random: jshn: uninitialized urandom read (4 bytes read) [ 10.851172] random: jshn: uninitialized urandom read (4 bytes read) [ 11.187184] urandom_read: 1 callbacks suppressed [ 11.187203] random: jshn: uninitialized urandom read (4 bytes read) [ 12.087562] rt3050-esw 10110000.esw: port 4 link down [ 12.643341] random: procd: uninitialized urandom read (4 bytes read) [ 13.710958] rt3050-esw 10110000.esw: port 4 link up [ 13.720954] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 13.749877] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 17.373058] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 17.396927] urandom-seed: Seed file not found (/etc/urandom.seed) [ 17.842611] procd: - early - [ 17.849350] procd: - watchdog - [ 19.168908] procd: - watchdog - [ 19.177024] procd: - ubus - [ 19.525811] random: ubusd: uninitialized urandom read (4 bytes read) [ 19.544280] random: ubusd: uninitialized urandom read (4 bytes read) [ 19.558493] random: ubusd: uninitialized urandom read (4 bytes read) [ 19.601552] procd: - init - [ 22.546631] kmodloader: loading kernel modules from /etc/modules.d/* [ 23.535530] i2c /dev entries driver [ 23.557959] i2c-ralink 10000900.i2c: clock 100KHz, re-start support [ 23.612417] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace [ 23.627722] Backport generated by backports.git v5.15.33-1-0-g183c4ab2 [ 23.820492] urngd: v1.0.2 started. [ 24.609808] PPP generic driver version 2.4.2 [ 24.638002] NET: Registered protocol family 24 [ 24.799966] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory" [ 24.814595] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected [ 24.830190] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected [ 24.844255] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 25.133496] kmodloader: done loading kernel modules from /etc/modules.d/* [ 25.631191] random: crng init done [ 25.638165] random: 1 urandom warning(s) missed due to ratelimiting [ 34.637180] [xx_custom] INFO: Timezone sanity check enabled: TIME_ZONE=Australia/Melbourne BOOT_TZ=UTC [ 34.672985] [xx_custom] WARNING: Timezone does not match, continuing [ 34.703138] [xx_custom] WARN: Unable to find eth0.1, will use generic hostname [ 34.734317] [xx_custom] INFO: Setting hostname to vocore-16m [ 34.785717] [xx_custom] INFO: Using fixed root password: send4help [ 34.871774] [xx_custom] INFO: Applying LAN configuration [ 34.939403] [xx_custom] INFO: Applying DHCP configuration [ 35.014879] [xx_custom] INFO: Applying NTP and timezone configuration [ 35.084979] [xx_custom] INFO: Applying miscellaneous settings [ 35.158617] [xx_custom] INFO: Setting system.autoconf=done [ 35.209210] [xx_custom] INFO: Finished applying custom default configuration, please check log for errors. [ 73.897657] rt3050-esw 10110000.esw: port 4 link down [ 75.537440] rt3050-esw 10110000.esw: port 4 link up [ 80.121147] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 80.164312] jffs2_build_filesystem(): unlocking the mtd device... [ 80.164339] done. [ 80.180661] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 92.473870] br-lan: port 1(eth0.1) entered blocking state [ 92.499743] br-lan: port 1(eth0.1) entered disabled state [ 92.511367] device eth0.1 entered promiscuous mode [ 92.521097] device eth0 entered promiscuous mode [ 92.914835] br-lan: port 1(eth0.1) entered blocking state [ 92.925765] br-lan: port 1(eth0.1) entered forwarding state [ 93.443717] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 339.179113] done. [ 339.183131] jffs2: notice: (1509) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 339.559945] overlayfs: upper fs does not support tmpfile. root@vocore-16m / #