U-Boot 2018.09 (Dec 05 2019 - 10:12:58 -0800) SoC: LS1023AE Rev1.1 (0x87920811) Clock Configuration: CPU0(A53):1000 MHz CPU1(A53):1000 MHz Bus: 300 MHz DDR: 1600 MT/s FMAN: 500 MHz Reset Configuration Word (RCW): 00000000: 0610000a 0a000000 00000000 00000000 00000010: 45580002 00000012 40044000 c1002000 00000020: 00000000 00000000 00000000 0003effe 00000030: 20004504 0418320a 00000096 00000001 Model: LS1043A QDS Board - T40/T20 Board: LS1043AQDS, boot from vBank: 0 I2C: ready DRAM: Initializing DDR... Detected UDIMM Fixed DDR4 on board 1.9 GiB (DDR4, 32-bit, CL=11, ECC off) Using SERDES1 Protocol: 17752 (0x4558) SEC Firmware: Bad firmware image (not a FIT image) Waking secondary cores to start from fbd35000 All (2) cores are up. MMC: FSL_SDHC: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB OK In: serial Out: serial Err: serial Net: SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB Fman1: Uploading microcode version 108.4.9 PCIe0: pcie@3400000 Root Complex: no link PCIe1: pcie@3500000 Root Complex: no link PCIe2: pcie@3600000 disabled FM1@DTSEC1 [PRIME], FM1@DTSEC2, FM1@DTSEC3, FM1@DTSEC5, FM1@DTSEC6 ### main_loop entered: bootdelay=5 ### main_loop: bootcmd="printenv" WatchGuard U-Boot 2018.09 - Dec 05 2019 10:12:58 +-------------------------------------------------------------------------+ |WatchGuard (SYSA) | |WatchGuard (SYSB Recovery/Diagnostic Mode) | | | | | | | | | | | | | | | | | | | +-------------------------------------------------------------------------+ Use the ^ and v keys to select which entry is highlighted. Press enter to boot the selected OS. password> fake => printenv loadaddr loadaddr=82000000 => setenv loadaddr 84000000 => run tftpload; setenv bootargs 'console=ttyS0,115200 earlycon=uart8250,mmio,0x21c0500 loglevel=8'; bootm ${loadaddr} Using FM1@DTSEC1 device TFTP from server 172.21.10.158; our IP address is 172.21.10.31 Filename 'watchguard_firebox-t20t40-kernel.itb'. Load address: 0x84000000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################## 5.3 MiB/s done Bytes transferred = 15871176 (f22cc8 hex) ## Loading kernel from FIT Image at 84000000 ... Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: ARM64 OpenWrt Linux-5.10.112 Created: 2022-04-26 3:44:05 UTC Type: Kernel Image Compression: gzip compressed Data Start: 0x840000ec Data Size: 15841678 Bytes = 15.1 MiB Architecture: AArch64 OS: Linux Load Address: 0x80000000 Entry Point: 0x80000000 Hash algo: crc32 Hash value: f7bfdf36 Hash algo: sha1 Hash value: 1b1b0c0289e161471927e3a737c7f4e5b821eeb6 Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 84000000 ... Using 'config-1' configuration Trying 'fdt-1' fdt subimage Description: ARM64 OpenWrt watchguard_firebox-t20t40 device tree blob Created: 2022-04-26 3:44:05 UTC Type: Flat Device Tree Compression: uncompressed Data Start: 0x84f1bbc8 Data Size: 27567 Bytes = 26.9 KiB Architecture: AArch64 Hash algo: crc32 Hash value: e2ba0ed7 Hash algo: sha1 Hash value: 9ef374ce483a60bd9365fb391b3b5fd6dc1ec358 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x84f1bbc8 Uncompressing Kernel Image ... OK Using Device Tree in place at 0000000084f1bbc8, end 0000000084f35776 WARNING: SEC firmware not running, no kaslr-seed WARNING failed to get smmu node: FDT_ERR_NOTFOUND WARNING failed to get smmu node: FDT_ERR_NOTFOUND Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.112 (aholmes@astraea-lnx) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19521-46980294f66) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP PREEMPT Tue Apr 26 03:44:05 2022 [ 0.000000] Machine model: WatchGuard FireBox T20/T40 [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0500 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000fb800000, size 4 MiB [ 0.000000] OF: reserved mem: initialized node qman-fqd, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000f8000000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node qman-pfdr, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000fa000000, size 16 MiB [ 0.000000] OF: reserved mem: initialized node bman-fbpr, compatible id shared-dma-pool [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] NUMA: NODE_DATA [mem 0xfb612e80-0xfb614d7f] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000f7ffffff] [ 0.000000] node 0: [mem 0x00000000fb000000-0x00000000fb7fffff] [ 0.000000] node 0: [mem 0x00000000fbc00000-0x00000000fbdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] On node 0 totalpages: 494080 [ 0.000000] DMA zone: 7928 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 494080 pages, LIFO batch:63 [ 0.000000] cma: Reserved 16 MiB at 0x00000000f5000000 [ 0.000000] percpu: Embedded 22 pages/cpu s51608 r8192 d30312 u90112 [ 0.000000] pcpu-alloc: s51608 r8192 d30312 u90112 alloc=22*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 486152 [ 0.000000] Policy zone: DMA [ 0.000000] Kernel command line: console=ttyS0,115200 earlycon=uart8250,mmio,0x21c0500 loglevel=8 [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1881804K/1976320K available (11070K kernel code, 1268K rwdata, 3056K rodata, 22144K init, 357K bss, 78132K reserved, 16384K cma-reserved) [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Adjusting CPU interface base to 0x000000000142f000 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] random: get_random_bytes called from start_kernel+0x348/0x4d4 with crng_init=0 [ 0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858 [ 0.000000] arch_timer: CPU0: Trapping CNTVCT access [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns [ 0.000004] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns [ 0.008483] Console: colour dummy device 80x25 [ 0.013027] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.023458] pid_max: default: 32768 minimum: 301 [ 0.028277] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.035737] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.044951] rcu: Hierarchical SRCU implementation. [ 0.050527] smp: Bringing up secondary CPUs ... [ 0.055468] Detected VIPT I-cache on CPU1 [ 0.055505] arch_timer: CPU1: Trapping CNTVCT access [ 0.055518] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.055595] smp: Brought up 1 node, 2 CPUs [ 0.075324] SMP: Total of 2 processors activated. [ 0.080056] CPU features: detected: 32-bit EL0 Support [ 0.085225] CPU features: detected: CRC32 instructions [ 0.090440] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.100476] CPU: All CPU(s) started at EL2 [ 0.104604] alternatives: patching kernel code [ 0.115135] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.125047] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.133137] NET: Registered protocol family 16 [ 0.139113] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations [ 0.146382] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.154381] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.163061] thermal_sys: Registered thermal governor 'step_wise' [ 0.163456] OF: /thermal-zones/core-cluster/cooling-maps/map0: could not find phandle [ 0.177392] thermal_sys: Add a cooling_device property with at least one device [ 0.184749] thermal_sys: failed to build thermal zone core-cluster: -2 [ 0.191485] cpuidle: using governor menu [ 0.195531] ASID allocator initialised with 65536 entries [ 0.201134] Serial: AMBA PL011 UART driver [ 0.219950] Machine: WatchGuard FireBox T20/T40 [ 0.224515] SoC family: QorIQ LS1043A [ 0.228205] SoC ID: svr:0x87920811, Revision: 1.1 [ 0.251675] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.258508] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.265252] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.272011] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.281668] raid6: skip pq benchmark and using algorithm neonx8 [ 0.288048] raid6: using neon recovery algorithm [ 0.295232] iommu: Default domain type: Passthrough [ 0.300480] vgaarb: loaded [ 0.303483] SCSI subsystem initialized [ 0.307455] libata version 3.00 loaded. [ 0.311892] pps_core: LinuxPPS API ver. 1 registered [ 0.316886] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.326519] PTP clock support registered [ 0.330621] fsl-ifc 1530000.ifc: Freescale Integrated Flash Controller [ 0.337248] fsl-ifc 1530000.ifc: IFC version 1.4, 8 banks [ 0.343707] clocksource: Switched to clocksource arch_sys_counter [ 0.350084] VFS: Disk quotas dquot_6.6.0 [ 0.354105] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.368312] NET: Registered protocol family 2 [ 0.372840] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.381438] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.390088] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.398187] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear) [ 0.405787] TCP: Hash tables configured (established 16384 bind 16384) [ 0.412441] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.419246] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.426573] NET: Registered protocol family 1 [ 0.430974] PCI: CLS 0 bytes, default 64 [ 0.543040] workingset: timestamp_bits=44 max_order=19 bucket_order=0 [ 0.550307] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.556435] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.566603] fuse: init (API version 7.32) [ 0.570722] SGI XFS with security attributes, realtime, no debug enabled [ 0.578098] xor: measuring software checksum speed [ 0.587921] 8regs : 1971 MB/sec [ 0.596530] 32regs : 2335 MB/sec [ 0.605883] arm64_neon : 1981 MB/sec [ 0.610263] xor: using function: 32regs (2335 MB/sec) [ 0.615384] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.624762] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: [ 0.632146] layerscape-pcie 3400000.pcie: IO 0x4000010000..0x400001ffff -> 0x0000000000 [ 0.640765] layerscape-pcie 3400000.pcie: MEM 0x4040000000..0x407fffffff -> 0x0040000000 [ 0.649512] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0000:00 [ 0.656279] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.661800] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.668033] pci_bus 0000:00: root bus resource [mem 0x4040000000-0x407fffffff] (bus address [0x40000000-0x7fffffff]) [ 0.678656] pci 0000:00:00.0: [1957:8088] type 01 class 0x060400 [ 0.684722] pci 0000:00:00.0: reg 0x38: [mem 0x4040000000-0x40400007ff pref] [ 0.691854] pci 0000:00:00.0: supports D1 D2 [ 0.696155] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 0.706076] pci 0000:00:00.0: BAR 6: assigned [mem 0x4040000000-0x40400007ff pref] [ 0.713712] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.719163] pcieport 0000:00:00.0: PME: Signaling with IRQ 81 [ 0.725143] pcieport 0000:00:00.0: AER: enabled with IRQ 81 [ 0.730975] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: [ 0.738368] layerscape-pcie 3500000.pcie: IO 0x4800010000..0x480001ffff -> 0x0000000000 [ 0.746980] layerscape-pcie 3500000.pcie: MEM 0x4840000000..0x487fffffff -> 0x0040000000 [ 0.755698] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0001:00 [ 0.762445] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.767975] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 0.777001] pci_bus 0001:00: root bus resource [mem 0x4840000000-0x487fffffff] (bus address [0x40000000-0x7fffffff]) [ 0.787617] pci 0001:00:00.0: [1957:8088] type 01 class 0x060400 [ 0.793674] pci 0001:00:00.0: reg 0x38: [mem 0x4840000000-0x48400007ff pref] [ 0.800807] pci 0001:00:00.0: supports D1 D2 [ 0.805107] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot [ 0.814945] pci 0001:00:00.0: BAR 6: assigned [mem 0x4840000000-0x48400007ff pref] [ 0.822566] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.827990] pcieport 0001:00:00.0: PME: Signaling with IRQ 82 [ 0.833954] pcieport 0001:00:00.0: AER: enabled with IRQ 82 [ 0.851643] bman_portal 508000000.bman-portal: Portal initialised, cpu 0 [ 0.858498] bman_portal 508010000.bman-portal: Portal initialised, cpu 1 [ 0.865954] qman_portal 500000000.qman-portal: Portal initialised, cpu 0 [ 0.873200] qman_portal 500010000.qman-portal: Portal initialised, cpu 1 [ 0.880643] rcpm 1ee2140.power-controller: can't request region for resource [mem 0x01ee2140-0x01ee2143] [ 0.890203] rcpm: probe of 1ee2140.power-controller failed with error -16 [ 0.897428] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.906433] printk: console [ttyS0] disabled [ 0.910789] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 45, base_baud = 18750000) is a 16550A [ 0.919678] printk: console [ttyS0] enabled [ 0.919678] printk: console [ttyS0] enabled [ 0.928074] printk: bootconsole [uart8250] disabled [ 0.928074] printk: bootconsole [uart8250] disabled [ 0.938239] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 45, base_baud = 18750000) is a 16550A [ 0.947371] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 46, base_baud = 18750000) is a 16550A [ 0.956496] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 46, base_baud = 18750000) is a 16550A [ 0.972577] brd: module loaded [ 0.978774] loop: module loaded [ 0.984010] spi-nor spi0.0: mx25u3235f (4096 Kbytes) [ 0.989027] 12 fixed-partitions partitions found on MTD device 1550000.spi [ 0.995918] Creating 12 MTD partitions on "1550000.spi": [ 1.001233] 0x000000000000-0x000000100000 : "rcw+pbi" [ 1.006710] 0x000000100000-0x000000200000 : "u-boot" [ 1.012001] 0x000000200000-0x000000210000 : "u-boot-env" [ 1.017639] 0x000000210000-0x000000220000 : "empty-1" [ 1.023010] 0x000000220000-0x000000240000 : "fman ucode" [ 1.028662] 0x000000240000-0x000000280000 : "empty-2-ppa" [ 1.034411] 0x000000280000-0x0000002a0000 : "wg-cfg0" [ 1.039805] 0x0000002a0000-0x0000002c0000 : "wg-cfg1" [ 1.045192] 0x0000002c0000-0x0000002e0000 : "wg-mfg" [ 1.050478] 0x0000002e0000-0x000000300000 : "empty-3" [ 1.055880] 0x000000300000-0x000000320000 : "fman-ucode-old" [ 1.061863] 0x000000320000-0x000000400000 : "wg-bootopt" [ 1.183531] fsl_dpaa_mac 1ae0000.ethernet: FMan MEMAC [ 1.188765] fsl_dpaa_mac 1ae0000.ethernet: FMan MAC address: 00:0b:6b:01:01:01 [ 1.196521] fsl_dpaa_mac 1ae2000.ethernet: FMan MEMAC [ 1.201577] fsl_dpaa_mac 1ae2000.ethernet: FMan MAC address: 00:0b:6b:01:01:02 [ 1.209036] fsl_dpaa_mac 1ae4000.ethernet: FMan MEMAC [ 1.214101] fsl_dpaa_mac 1ae4000.ethernet: FMan MAC address: 00:0b:6b:01:01:03 [ 1.221801] fsl_dpaa_mac 1ae8000.ethernet: FMan MEMAC [ 1.226869] fsl_dpaa_mac 1ae8000.ethernet: FMan MAC address: 00:0b:6b:01:01:05 [ 1.234572] fsl_dpaa_mac 1aea000.ethernet: FMan MEMAC [ 1.239628] fsl_dpaa_mac 1aea000.ethernet: FMan MAC address: 00:0b:6b:01:01:06 [ 1.271651] fsl_dpaa_mac 1ae0000.ethernet eth0: Probed interface eth0 [ 1.302173] fsl_dpaa_mac 1ae2000.ethernet eth1: Probed interface eth1 [ 1.338882] fsl_dpaa_mac 1ae4000.ethernet eth2: Probed interface eth2 [ 1.371465] fsl_dpaa_mac 1ae8000.ethernet eth3: Probed interface eth3 [ 1.403697] fsl_dpaa_mac 1aea000.ethernet eth4: Probed interface eth4 [ 1.412618] VFIO - User Level meta-driver version: 0.3 [ 1.420995] mousedev: PS/2 mouse device common for all mice [ 1.429649] ftm-alarm 29d0000.timer: registered as rtc1 [ 1.435234] i2c /dev entries driver [ 1.439243] ptp_qoriq: device tree node missing required elements, try automatic configuration [ 1.447978] pps pps0: new PPS source ptp0 [ 1.471799] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 1.479592] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver [ 1.488146] sdhci: Secure Digital Host Controller Interface driver [ 1.494366] sdhci: Copyright(c) Pierre Ossman [ 1.498721] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.505255] caam 1700000.crypto: Linux CAAM Queue I/F driver initialised [ 1.511981] caam 1700000.crypto: Entropy delay = 3200 [ 1.530656] mmc0: SDHCI controller on 1560000.esdhc [1560000.esdhc] using ADMA 64-bit [ 1.543791] caam 1700000.crypto: Instantiated RNG4 SH0 [ 1.570526] caam 1700000.crypto: Instantiated RNG4 SH1 [ 1.575684] caam 1700000.crypto: device ID = 0x0a12060000000000 (Era 8) [ 1.582300] caam 1700000.crypto: job rings = 3, qi = 1 [ 1.593569] caam algorithms registered in /proc/crypto [ 1.599857] caam 1700000.crypto: caam pkc algorithms registered in /proc/crypto [ 1.607239] caam 1700000.crypto: registering rng-caam [ 1.616175] caam 1700000.crypto: algorithms registered in /proc/crypto [ 1.623434] hid: raw HID events driver (C) Jiri Kosina [ 1.629956] NET: Registered protocol family 10 [ 1.635773] Segment Routing with IPv6 [ 1.639541] NET: Registered protocol family 17 [ 1.644115] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.657148] 8021q: 802.1Q VLAN Support v1.8 [ 1.661466] mmc0: new HS200 MMC card at address 0001 [ 1.662864] Btrfs loaded, crc32c=crc32c-generic [ 1.667425] mmcblk0: mmc0:0001 M62704 3.56 GiB [ 1.674070] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 1.675810] mmcblk0boot0: mmc0:0001 M62704 partition 1 2.00 MiB [ 1.681910] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 1.687806] mmcblk0boot1: mmc0:0001 M62704 partition 2 2.00 MiB [ 1.699629] mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB, chardev (244:0) [ 1.708402] mmcblk0: p1 p2 p3 p4 < p5 p6 p7 > [ 1.714811] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 1.718801] Freeing unused kernel memory: 22144K [ 1.733961] Run /init as init process [ 1.737625] with arguments: [ 1.740588] /init [ 1.742857] with environment: [ 1.746023] HOME=/ [ 1.746028] random: fast init done [ 1.748380] TERM=linux [ 1.799585] random: crng init done [ 2.078822] init: Console is alive [ 2.082349] init: - watchdog - [ 2.093039] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.104566] pps_ldisc: PPS line discipline registered [ 2.115909] usbcore: registered new interface driver usbfs [ 2.121441] usbcore: registered new interface driver hub [ 2.126871] usbcore: registered new device driver usb [ 2.133884] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.143173] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 2.152228] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 2.163016] scsi host0: ahci-qoriq [ 2.166642] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 57 [ 2.175057] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.505268] ata1: SATA link down (SStatus 0 SControl 300) [ 2.512869] ehci-fsl: Freescale EHCI Host controller driver [ 2.519270] ehci-platform: EHCI generic platform driver [ 2.527883] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.534572] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.542597] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.548182] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 2.556054] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 2.565502] xhci-hcd xhci-hcd.1.auto: irq 54, io mem 0x02f00000 [ 2.571967] hub 1-0:1.0: USB hub found [ 2.575752] hub 1-0:1.0: 1 port detected [ 2.580118] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.584279] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.586915] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.591770] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 2.605548] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 2.612117] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.620572] hub 2-0:1.0: USB hub found [ 2.624349] hub 2-0:1.0: 1 port detected [ 2.628607] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.634136] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 2.635255] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.640519] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3 [ 2.654129] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 2.663569] xhci-hcd xhci-hcd.2.auto: irq 55, io mem 0x03000000 [ 2.669974] hub 3-0:1.0: USB hub found [ 2.673765] hub 3-0:1.0: 1 port detected [ 2.678013] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.684129] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 2.684173] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4 [ 2.690447] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.697401] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed [ 2.710037] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.718488] hub 4-0:1.0: USB hub found [ 2.722258] hub 4-0:1.0: 1 port detected [ 2.726514] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.730539] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller [ 2.732916] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.738207] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 5 [ 2.751991] xhci-hcd xhci-hcd.3.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 2.761470] xhci-hcd xhci-hcd.3.auto: irq 56, io mem 0x03100000 [ 2.767870] hub 5-0:1.0: USB hub found [ 2.771637] hub 5-0:1.0: 1 port detected [ 2.775901] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.782207] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller [ 2.787716] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 6 [ 2.795597] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.801769] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0 SuperSpeed [ 2.808403] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.816861] hub 6-0:1.0: USB hub found [ 2.820628] hub 6-0:1.0: 1 port detected [ 2.824888] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.834202] usbcore: registered new interface driver usb-storage [ 2.841419] qoriq_thermal 1f00000.tmu: Failed to register sensors [ 2.845386] usbcore: registered new interface driver uas [ 2.852961] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 2.870513] init: - preinit - [ 3.043120] qoriq_thermal 1f00000.tmu: Failed to register sensors Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 6.134609] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 7.558403] procd: - early - [ 7.561412] procd: - watchdog - [ 8.132442] procd: - watchdog - [ 8.135945] procd: - ubus - [ 8.189825] procd: - init - Please press Enter to activate this console. [ 8.330488] urngd: v1.0.2 started. [ 8.358639] kmodloader: loading kernel modules from /etc/modules.d/* [ 8.423037] Key type cifs.idmap registered [ 8.458976] PPP generic driver version 2.4.2 [ 8.464172] NET: Registered protocol family 24 [ 8.472162] kmodloader: done loading kernel modules from /etc/modules.d/* [ 10.160159] [xx_custom] INFO: Timezone sanity check enabled: TIME_ZONE=Australia/Melbourne BOOT_TZ=UTC [ 10.172912] [xx_custom] WARNING: Timezone does not match, continuing [ 10.185220] [xx_custom] INFO: Setting hostname to firebox-t20-010101 [ 10.198647] [xx_custom] INFO: Using fixed root password: [redacted] [ 10.214204] [xx_custom] INFO: Applying LAN configuration [ 10.229991] [xx_custom] INFO: Applying DHCP configuration [ 10.247923] [xx_custom] INFO: Applying NTP and timezone configuration [ 10.264476] [xx_custom] INFO: Applying miscellaneous settings [ 10.286938] [xx_custom] INFO: Setting system.autoconf=done [ 10.299402] [xx_custom] INFO: Finished applying custom default configuration, please check log for errors. BusyBox v1.35.0 (2022-04-24 21:09:51 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt firebox-t20, r19521+1-46980294f66 ----------------------------------------------------- root@firebox-t20-010101 / #