1. U-Boot 2018.09 (Dec 05 2019 - 10:12:58 -0800)
2. ​
3. SoC: LS1023AE Rev1.1 (0x87920811)
4. Clock Configuration:
5. CPU0(A53):1000 MHz CPU1(A53):1000 MHz
6. Bus: 300 MHz DDR: 1600 MT/s FMAN: 500 MHz
7. Reset Configuration Word (RCW):
8. 00000000: 0610000a 0a000000 00000000 00000000
9. 00000010: 45580002 00000012 40044000 c1002000
10. 00000020: 00000000 00000000 00000000 0003effe
11. 00000030: 20004504 0418320a 00000096 00000001
12. Model: LS1043A QDS Board - T40/T20
13. Board: LS1043AQDS, boot from vBank: 0
14. I2C: ready
15. DRAM: Initializing DDR...
16. Detected UDIMM Fixed DDR4 on board
17. 1.9 GiB (DDR4, 32-bit, CL=11, ECC off)
18. Using SERDES1 Protocol: 17752 (0x4558)
19. SEC Firmware: Bad firmware image (not a FIT image)
20. Waking secondary cores to start from fbd35000
21. All (2) cores are up.
22. MMC: FSL_SDHC: 0
23. Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
24. OK
25. In: serial
26. Out: serial
27. Err: serial
28. Net: SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
29. Fman1: Uploading microcode version 108.4.9
30. PCIe0: pcie@3400000 Root Complex: no link
31. PCIe1: pcie@3500000 Root Complex: no link
32. PCIe2: pcie@3600000 disabled
33. FM1@DTSEC1 [PRIME], FM1@DTSEC2, FM1@DTSEC3, FM1@DTSEC5, FM1@DTSEC6
34. ### main_loop entered: bootdelay=5
35. ​
36. ### main_loop: bootcmd="printenv"
37. ​
38. WatchGuard U-Boot 2018.09 - Dec 05 2019 10:12:58
39. ​
40. +-------------------------------------------------------------------------+
41. |WatchGuard (SYSA) |
42. |WatchGuard (SYSB Recovery/Diagnostic Mode) |
43. | |
44. | |
45. | |
46. | |
47. | |
48. | |
49. | |
50. | |
51. | |
52. +-------------------------------------------------------------------------+
53. ​
54. Use the ^ and v keys to select which entry is highlighted.
55. Press enter to boot the selected OS.
56. ​
57. ​
58. ​
59. ​
60. ​
61. ​
62. password> ass
63. ​
64. => printenv
65. SysARoot=mmcblk0p3
66. SysBRoot=mmcblk0p2
67. WGKernelfile=kernel_T20_T40_prod.itb
68. arch=arm
69. baudrate=115200
70. board=ls1043aqds_t20
71. board_name=ls1043aqds_t20
72. boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
73. boot_efi_binary=if fdt addr ${fdt_addr_r}; then bootefi bootmgr ${fdt_addr_r};else bootefi bootmgr ${fdtcontroladdr};fi;load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} efi/boot/bootaa64.efi; if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r};else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi
74. boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf
75. boot_net_pci_enum=pci enum
76. boot_net_usb_start=usb start
77. boot_os=y
78. boot_prefixes=/ /boot/
79. boot_script_dhcp=boot.scr.uimg
80. boot_script_hdr=hdr_ls1043ardb_bs.out
81. boot_scripts=ls1043ardb_boot.scr
82. boot_targets=mmc0 usb0
83. bootargs=console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)
84. bootcmd=printenv
85. bootcmd_mmc0=setenv devnum 0; run mmc_boot
86. bootcmd_usb0=setenv devnum 0; run usb_boot
87. bootdelay=5
88. consoledev=ttyS0
89. cpu=armv8
90. distro_bootcmd=setenv scsi_need_init; for target in ${boot_targets}; do run bootcmd_${target}; done
91. efi_dtb_prefixes=/ /dtb/ /dtb/current/
92. eth1addr=00:0B:6B:01:01:02
93. eth2addr=00:0B:6B:01:01:03
94. eth3addr=00:0B:6B:01:01:04
95. eth4addr=00:0B:6B:01:01:05
96. eth5addr=00:0B:6B:01:01:06
97. ethact=FM1@DTSEC1
98. ethaddr=00:0B:6B:01:01:01
99. ethprime=FM1@DTSEC1
100. fdt_addr=0x64f00000
101. fdt_addr_r=0x90000000
102. fdt_high=0xffffffffffffffff
103. fdtcontroladdr=fbc2e288
104. fdtheader_addr_r=0x80100000
105. flash_bootloader=tftp 0x82000000 u-boot_ls1043aqds_wg_t20_qspi.bin;sf probe 0; sf erase 0 0x100000; sf write 0x82000000 0 $filesize;sf read 0x80000000 0 $filesize; cmp.b 0x82000000 0x80000000 $filesize;
106. fman_ucode=fbc3d540
107. hwconfig=fsl_ddr:bank_intlv=auto
108. initrd_high=0xffffffffffffffff
109. ipaddr=192.168.1.1
110. kernel_addr=0x61000000
111. kernel_addr_r=0x81000000
112. kernel_addr_sd=0x8000
113. kernel_size=0x2800000
114. kernel_size_sd=0x14000
115. kernel_start=0x1000000
116. kernelhdr_addr_sd=0x4000
117. kernelhdr_size_sd=0x10
118. kernelheader_addr=0x60800000
119. kernelheader_addr_r=0x80200000
120. kernelheader_size=0x40000
121. kernelheader_start=0x800000
122. load_addr=0xa0000000
123. load_efi_dtb=load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} ${prefix}${efi_fdtfile}
124. loadaddr=82000000
125. mmc_boot=if mmc dev ${devnum}; then setenv devtype mmc; run scan_dev_for_boot_part; fi
126. mtdparts=mtdparts=spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)
127. netmask=255.255.255.0
128. nuke_env=sf probe 0;sf erase 0x200000 10000;
129. scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;run scan_dev_for_efi;
130. scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done
131. scan_dev_for_efi=setenv efi_fdtfile ${fdtfile}; for prefix in ${efi_dtb_prefixes}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${efi_fdtfile}; then run load_efi_dtb; fi;done;if test -e ${devtype} ${devnum}:${distro_bootpart} efi/boot/bootaa64.efi; then echo Found EFI removable media binary efi/boot/bootaa64.efi; run boot_efi_binary; echo EFI LOAD FAILED: continuing...; fi; setenv efi_fdtfile
132. scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi
133. scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
134. scriptaddr=0x80000000
135. scripthdraddr=0x80080000
136. scsi_boot=run scsi_init; if scsi dev ${devnum}; then setenv devtype scsi; run scan_dev_for_boot_part; fi
137. scsi_init=if ${scsi_need_init}; then setenv scsi_need_init false; scsi scan; fi
138. serveraddr=10.0.1.13;
139. serverip=192.168.1.100
140. soc=fsl-layerscape
141. stderr=serial
142. stdin=serial
143. stdout=serial
144. usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run scan_dev_for_boot_part; fi
145. vendor=freescale
146. wgBootRecovery=setenv bootargs wgmode=safe root=/dev/$SysARoot rw console=$consoledev,$baudrate $othbootargs earlycon=uart8250,mmio,0x21c0500; mmc info; ext2load mmc 0:3 $loadaddr $WGKernelfile; bootm $loadaddr;
147. wgBootSysA=setenv bootargs root=/dev/$SysARoot rw rootdelay=2 console=$consoledev,$baudrate $othbootargs earlycon=uart8250,mmio,0x21c0500; mmc info; ext2load mmc 0:3 $loadaddr $WGKernelfile; bootm $loadaddr;
148. wgBootSysB=setenv bootargs root=/dev/$SysBRoot rw rootdelay=2 console=$consoledev,$baudrate $othbootargs earlycon=uart8250,mmio,0x21c0500; mmc info; ext2load mmc 0:2 $loadaddr $WGKernelfile; bootm $loadaddr;
149. ​
150. Environment size: 5011/8188 bytes
151. ​
152. => mmc info
153. Device: FSL_SDHC
154. Manufacturer ID: 70
155. OEM: 100
156. Name: M6270
157. Bus Speed: 52000000
158. Mode : MMC High Speed (52MHz)
159. Rd Block Len: 512
160. MMC version 5.0
161. High Capacity: Yes
162. Capacity: 3.6 GiB
163. Bus Width: 4-bit
164. Erase Group Size: 512 KiB
165. HC WP Group Size: 4 MiB
166. User Capacity: 3.6 GiB WRREL
167. Boot Capacity: 2 MiB ENH
168. RPMB Capacity: 512 KiB ENH
169. => mmc dev
170. switch to partitions #0, OK
171. mmc0(part 0) is current device
172. => help
173. 74lv164 - 74lv164 control
174. ? - alias for 'help'
175. base - print or set address offset
176. bdinfo - print Board Info structure
177. blkcache- block cache diagnostics and control
178. boot - boot default, i.e., run 'bootcmd'
179. bootd - boot default, i.e., run 'bootcmd'
180. bootefi - Boots an EFI payload from memory
181. bootelf - Boot from an ELF image in memory
182. booti - boot arm64 Linux Image image from memory
183. bootm - boot application image from memory
184. bootp - boot image via network using BOOTP/TFTP protocol
185. bootvx - Boot vxWorks from an ELF image
186. bootz - boot Linux zImage image from memory
187. cmp - memory compare
188. coninfo - print console devices and information
189. cp - memory copy
190. cpu - Multiprocessor CPU boot manipulation and release
191. crc32 - checksum calculation
192. date - get/set/reset date & time
193. dcache - enable or disable data cache
194. dhcp - boot image via network using DHCP/TFTP protocol
195. echo - echo args to console
196. editenv - edit environment variable
197. env - environment handling commands
198. erase - erase FLASH memory
199. exit - exit script
200. ext2load- load binary file from a Ext2 filesystem
201. ext2ls - list files in a directory (default /)
202. ext4load- load binary file from a Ext4 filesystem
203. ext4ls - list files in a directory (default /)
204. ext4size- determine a file's size
205. false - do nothing, unsuccessfully
206. fatinfo - print information about filesystem
207. fatload - load binary file from a dos filesystem
208. fatls - list files in a directory (default /)
209. fatsize - determine a file's size
210. fdt - flattened device tree utility commands
211. flinfo - print FLASH memory information
212. fstype - Look up a filesystem type
213. go - start application at address 'addr'
214. gpio - query and control gpio pins
215. gpt - GUID Partition Table
216. grepenv - search environment variables
217. gzwrite - unzip and write memory to block device
218. hash - compute hash message digest
219. help - print command description/usage
220. i2c - I2C sub-system
221. icache - enable or disable instruction cache
222. iminfo - print header information for application image
223. imxtract- extract a part of a multi-image
224. itest - return true/false on integer compare
225. led - LED control
226. load - load binary file from a filesystem
227. loadb - load binary file over serial line (kermit mode)
228. loads - load S-Record file over serial line
229. loadx - load binary file over serial line (xmodem mode)
230. loady - load binary file over serial line (ymodem mode)
231. loop - infinite loop on address range
232. ls - list files in a directory (default /)
233. lzmadec - lzma uncompress a memory region
234. md - memory display
235. mdio - MDIO utility commands
236. meminfo - display memory information
237. mii - MII utility commands
238. mm - memory modify (auto-incrementing address)
239. mmc - MMC sub system
240. mmcinfo - display MMC info
241. mtest - simple RAM read/write test
242. mw - memory write (fill)
243. nfs - boot image via network using NFS protocol
244. nm - memory modify (constant address)
245. part - disk partition related commands
246. pci - list and access PCI Configuration Space
247. ping - send ICMP ECHO_REQUEST to network host
248. printenv- print environment variables
249. protect - enable or disable FLASH write protection
250. pxe - commands to get and boot from pxe files
251. qixis_reset- Reset the board using the FPGA sequencer
252. reset - Perform RESET of the CPU
253. run - run commands in an environment variable
254. save - save file to a filesystem
255. saveenv - save environment variables to persistent storage
256. scsi - SCSI sub-system
257. scsiboot- boot from SCSI device
258. setenv - set environment variables
259. setexpr - set environment variable as the result of eval expression
260. sf - SPI flash sub-system
261. showvar - print local hushshell variables
262. size - determine a file's size
263. sleep - delay execution for some time
264. source - run script from memory
265. sysboot - command to get and boot from syslinux files
266. test - minimal test like /bin/sh
267. tftpboot- boot image via network using TFTP protocol
268. true - do nothing, successfully
269. unzip - unzip a memory region
270. usb - USB sub-system
271. usbboot - boot from USB device
272. vdd_override- override VDD
273. vdd_read- read VDD
274. version - print monitor, compiler and linker version
275. => ext4ls mmc 0:3
276. <DIR> 1024 .
277. <DIR> 1024 ..
278. <DIR> 12288 lost+found
279. 217 info.txt
280. <DIR> 1024 proc
281. <DIR> 1024 initrd
282. <DIR> 1024 tools
283. <DIR> 1024 usr
284. <DIR> 1024 root
285. <DIR> 3072 sbin
286. <DIR> 1024 boot
287. <DIR> 1024 home
288. <DIR> 16384 dev
289. <DIR> 1024 sysfs
290. <SYM> 3 lib64
291. <DIR> 1024 var
292. <DIR> 3072 etc
293. <DIR> 15360 lib
294. <DIR> 1024 pending
295. <DIR> 1024 bin
296. <DIR> 1024 tmp
297. <DIR> 1024 opt
298. <DIR> 1024 sys
299. 10420940 kernel_T20_T40.itb
300. 10420940 kernel_T20_T40_prod.itb
301. <DIR> 1024 data2
302. => ext4ls mmc 0:3 etc
303. <DIR> 3072 .
304. <DIR> 1024 ..
305. 0 diskpt_once
306. <SYM> 19 default.xml
307. 512 random-seed
308. 5762 CRYPTO-POST.req
309. 7052 tcsd.conf
310. <DIR> 1024 ssh
311. <DIR> 1024 mdev.d
312. 178 fw_env.config
313. <DIR> 1024 runlevel
314. <DIR> 1024 oss-conf
315. 2597 services
316. <DIR> 1024 sysa
317. <DIR> 1024 wgsync
318. 118 wapid.conf
319. <SYM> 17 mdev.conf
320. <DIR> 1024 defaults
321. 39119 dhcp_fingerprints.conf
322. <SYM> 28 snmpd.conf
323. <DIR> 1024 nginx
324. <DIR> 1024 raddb
325. <DIR> 1024 fonts
326. 142 lickey.pem
327. 1235 passwd
328. <DIR> 1024 ppp
329. <DIR> 1024 csfc_post
330. <DIR> 1024 libnl
331. 972 conntrackd.conf
332. <DIR> 1024 schema
333. 443 loggerd-modules.conf
334. 1325 country_spec_00.xml
335. <DIR> 1024 iproute2
336. <DIR> 1024 json-schema
337. 6995 CRYPTO-POST.rsp
338. 237 group
339. <DIR> 1024 proxy
340. <DIR> 3072 inittab.d
341. <DIR> 1024 stylesheet
342. 451 diag_access_public.pem
343. <DIR> 1024 tdts
344. 259 nsswitch.conf
345. 98 code-signature
346. <DIR> 1024 rsyncd-modules
347. 587219 defaultT40.xml
348. 314 netdbg.cfg
349. 11755 termcap
350. 686 protocols
351. <DIR> 1024 tdr
352. 520 guac-standalone.cfg
353. 2802 country_spec_us.xml
354. 32 shells
355. 1362 ethertypes
356. <DIR> 1024 wg
357. 605784 magic.mgc
358. 61 wvmodemscan.conf
359. 33 snmp-wrap.conf
360. <SYM> 12 mtab
361. 587199 defaultT20.xml
362. <SYM> 16 wvdial.conf
363. 160 hosts-default
364. 1 lsb-release
365. 355 hmacsums.txt
366. <DIR> 1024 radiusclient
367. 123348 product_table.json
368. <SYM> 17 localtime
369. <DIR> 1024 fmc
370. <SYM> 20 resolv.conf
371. <DIR> 3072 licenses
372. 853 fstab
373. <DIR> 1024 pam.d
374. <SYM> 10 hosts
375. 460 rsyncd.conf
376. 178 codesign-public.pem
377. 192429 code-signed
378. => setenv wgBootSysA 'setenv bootargs root=/dev/$SysARoot rw rootdelay=2 console=$consoledev,$baudrate earlycon=uart8250,mmio,0x21c0500 $othbootargs; mmc info; ext2load mmc 0:3 $loadaddr $WGKernelfile; bootm $loadaddr;'
379. => setenv othbootargs 'loglevel=8 single'
380. => saveenv
381. Saving Environment to SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
382. Erasing SPI flash...Writing to SPI flash...done
383. OK
384. => run wgBootSysA
385. Device: FSL_SDHC
386. Manufacturer ID: 70
387. OEM: 100
388. Name: M6270
389. Bus Speed: 52000000
390. Mode : MMC High Speed (52MHz)
391. Rd Block Len: 512
392. MMC version 5.0
393. High Capacity: Yes
394. Capacity: 3.6 GiB
395. Bus Width: 4-bit
396. Erase Group Size: 512 KiB
397. HC WP Group Size: 4 MiB
398. User Capacity: 3.6 GiB WRREL
399. Boot Capacity: 2 MiB ENH
400. RPMB Capacity: 512 KiB ENH
401. 10420940 bytes read in 612 ms (16.2 MiB/s)
402. ## Loading kernel from FIT Image at 82000000 ...
403. Using 'conf@1' configuration
404. Trying 'kernel@1' kernel subimage
405. Description: WatchGuard Kernel
406. Created: 2022-01--8 1:26:08 UTC
407. Type: Kernel Image
408. Compression: gzip compressed
409. Data Start: 0x820000cc
410. Data Size: 10386949 Bytes = 9.9 MiB
411. Architecture: AArch64
412. OS: Linux
413. Load Address: 0x80080000
414. Entry Point: 0x80080000
415. Hash algo: crc32
416. Hash value: 9b4fb984
417. Hash algo: sha1
418. Hash value: fc46e7e04922b05ce0863c4c05ae2f62b964d1d8
419. Verifying Hash Integrity ... crc32+ sha1+ OK
420. ## Loading fdt from FIT Image at 82000000 ...
421. Using 'conf@1' configuration
422. Trying 'fdt@1' fdt subimage
423. Description: Flattened Device Tree blob
424. Created: 2022-01--8 1:26:08 UTC
425. Type: Flat Device Tree
426. Compression: uncompressed
427. Data Start: 0x829e8000
428. Data Size: 32642 Bytes = 31.9 KiB
429. Architecture: AArch64
430. Load Address: 0x90000000
431. Hash algo: crc32
432. Hash value: 8ac87d7b
433. Hash algo: sha1
434. Hash value: 01635f39bd4bb64375dce2d6e03b2bda97f89275
435. Verifying Hash Integrity ... crc32+ sha1+ OK
436. Loading fdt from 0x829e8000 to 0x90000000
437. Booting using the fdt blob at 0x90000000
438. Uncompressing Kernel Image ... OK
439. Using Device Tree in place at 0000000090000000, end 000000009001af81
440. WARNING: SEC firmware not running, no kaslr-seed
441. WARNING failed to get smmu node: FDT_ERR_NOTFOUND
442. WARNING failed to get smmu node: FDT_ERR_NOTFOUND
443. ​
444. Starting kernel ...
445. ​
446. [ 0.000000] Booting Linux on physical CPU 0x0
447. [ 0.000000] Linux version 4.14.83 (release@cmrb06) (gcc version 6.5.0 (crosstool-NG 1.23.0.580-eb72b4e)) #1 SMP PREEMPT Wed Dec 22 17:22:15 PST 2021
448. [ 0.000000] Boot CPU: AArch64 Processor [410fd034]
449. [ 0.000000] Machine model: LS1043A RDB Board - T40
450. [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0500 (options '')
451. [ 0.000000] bootconsole [uart8250] enabled
452. [ 0.000000] efi: Getting EFI parameters from FDT:
453. [ 0.000000] efi: UEFI not found.
454. [ 0.000000] crashkernel reserved: 0x00000000f8600000 - 0x00000000fbe00000 (56 MB)
455. [ 0.000000] OF: reserved mem: initialized node qman-fqd, compatible id fsl,qman-fqd
456. [ 0.000000] OF: reserved mem: initialized node qman-pfdr, compatible id fsl,qman-pfdr
457. [ 0.000000] OF: reserved mem: initialized node bman-fbpr, compatible id fsl,bman-fbpr
458. [ 0.000000] cma: Reserved 16 MiB at 0x00000000f4000000
459. [ 0.000000] On node 0 totalpages: 494080
460. [ 0.000000] DMA zone: 6937 pages used for memmap
461. [ 0.000000] DMA zone: 0 pages reserved
462. [ 0.000000] DMA zone: 494080 pages, LIFO batch:31
463. [ 0.000000] percpu: Embedded 22 pages/cpu @ffff800078575000 s50904 r8192 d31016 u90112
464. [ 0.000000] pcpu-alloc: s50904 r8192 d31016 u90112 alloc=22*4096
465. [ 0.000000] pcpu-alloc: [0] 0 [0] 1
466. [ 0.000000] Detected VIPT I-cache on CPU0
467. [ 0.000000] CPU features: enabling workaround for ARM erratum 845719
468. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 487143
469. [ 0.000000] Kernel command line: root=/dev/mmcblk0p3 rw rootdelay=2 console=ttyS0,115200 earlycon=uart8250,mmio,0x21c0500 loglevel=8 single
470. [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
471. [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
472. [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
473. [ 0.000000] Memory: 1852420K/1976320K available (7996K kernel code, 518K rwdata, 2944K rodata, 5376K init, 849K bss, 107516K reserved, 16384K cma-reserved)
474. [ 0.000000] Virtual kernel memory layout:
475. [ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB)
476. [ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB)
477. [ 0.000000] .text : 0xffff000008080000 - 0xffff000008850000 ( 8000 KB)
478. [ 0.000000] .rodata : 0xffff000008850000 - 0xffff000008b40000 ( 3008 KB)
479. [ 0.000000] .init : 0xffff000008b40000 - 0xffff000009080000 ( 5376 KB)
480. [ 0.000000] .data : 0xffff000009080000 - 0xffff000009101a00 ( 519 KB)
481. [ 0.000000] .bss : 0xffff000009101a00 - 0xffff0000091d6108 ( 850 KB)
482. [ 0.000000] fixed : 0xffff7dfffe7fb000 - 0xffff7dfffec00000 ( 4116 KB)
483. [ 0.000000] PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB)
484. [ 0.000000] vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum)
485. [ 0.000000] 0xffff7e0000000000 - 0xffff7e0001b19000 ( 27 MB actual)
486. [ 0.000000] memory : 0xffff800000000000 - 0xffff80007be00000 ( 1982 MB)
487. [ 0.000000] Preemptible hierarchical RCU implementation.
488. [ 0.000000] RCU event tracing is enabled.
489. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
490. [ 0.000000] Tasks RCU enabled.
491. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
492. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
493. [ 0.000000] GIC: Adjusting CPU interface base to 0x000000000142f000
494. [ 0.000000] GIC: Using split EOI/Deactivate mode
495. [ 0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858
496. [ 0.000000] arch_timer: CPU0: Trapping CNTVCT access
497. [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
498. [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
499. [ 0.000004] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
500. [ 0.008589] Console: colour dummy device 80x25
501. [ 0.013079] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000)
502. [ 0.023506] pid_max: default: 32768 minimum: 301
503. [ 0.028218] Security Framework initialized
504. [ 0.032386] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
505. [ 0.039145] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
506. [ 0.062384] ASID allocator initialised with 32768 entries
507. [ 0.075844] Hierarchical SRCU implementation.
508. [ 0.088268] WG CPU Model 1043 Count 4
509. [ 0.092035] WG CRASH MIN RESERVE 56 MB
510. [ 0.096073]
511. [ 0.096073] wg_kernel_init: Built Dec 22 2021 17:11:46
512. [ 0.103071] EFI services will not be available.
513. [ 0.115654] smp: Bringing up secondary CPUs ...
514. [ 0.148332] Detected VIPT I-cache on CPU1
515. [ 0.148364] arch_timer: CPU1: Trapping CNTVCT access
516. [ 0.148370] CPU1: Booted secondary processor [410fd034]
517. [ 0.148433] smp: Brought up 1 node, 2 CPUs
518. [ 0.166866] SMP: Total of 2 processors activated.
519. [ 0.171606] CPU features: detected feature: 32-bit EL0 Support
520. [ 0.177489] CPU features: detected feature: Kernel page table isolation (KPTI)
521. [ 0.193439] CPU: All CPU(s) started at EL2
522. [ 0.197572] alternatives: patching kernel code
523. [ 0.202276] wg_check_smp_cpus: CPUs offline, found 2, expected 4.
524. [ 0.202280] wg_check_smp_cpus: CPUs offline, found 2, expected 4.
525. [ 0.219550] random: get_random_u32 called from bucket_table_alloc+0xf8/0x280 with crng_init=0
526. [ 0.228387] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
527. [ 0.238207] futex hash table entries: 512 (order: 3, 32768 bytes)
528. [ 0.244901] alloc_chrdev_region: 254:0 gpiochip
529. [ 0.249732] DMI not present or invalid.
530. [ 0.253784] NET: Registered protocol family 16
531. [ 0.258606] alloc_chrdev_region: 253:0 fsl_mc_bus
532. [ 0.267552] cpuidle: using governor menu
533. [ 0.271965] Bman ver:0a02,02,01
534. [ 0.277516] qman-fqd addr 0x00000000f8000000 size 0x400000
535. [ 0.283045] qman-pfdr addr 0x00000000f6000000 size 0x2000000
536. [ 0.288769] Qman ver:0a01,03,02,00
537. [ 0.292339] vdso: 2 pages (1 code @ ffff000008857000, 1 data @ ffff000009084000)
538. [ 0.299801] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
539. [ 0.307508] DMA: preallocated 256 KiB pool for atomic allocations
540. [ 0.313741] Serial: AMBA PL011 UART driver
541. [ 0.318846] Machine: LS1043A RDB Board - T40
542. [ 0.323150] SoC family: QorIQ LS1043A
543. [ 0.326830] SoC ID: svr:0x87920811, Revision: 1.1
544. [ 0.355544] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
545. [ 0.363974] ACPI: Interpreter disabled.
546. [ 0.369962] alloc_chrdev_region: 252:0 tpm
547. [ 0.374791] misc_register: 10, 63 vga_arbiter
548. [ 0.379404] vgaarb: loaded
549. [ 0.382288] SCSI subsystem initialized
550. [ 0.386185] libata version 3.00 loaded.
551. [ 0.390238] usbcore: registered new interface driver usbfs
552. [ 0.395836] usbcore: registered new interface driver hub
553. [ 0.401231] usbcore: registered new device driver usb
554. [ 0.406391] alloc_chrdev_region: 251:0 rtc
555. [ 0.411237] i2c i2c-0: IMX I2C adapter registered
556. [ 0.416023] i2c i2c-0: using dma0chan16 (tx) and dma0chan17 (rx) for DMA transfers
557. [ 0.423906] alloc_chrdev_region: 250:0 pps
558. [ 0.428209] pps_core: LinuxPPS API ver. 1 registered
559. [ 0.433225] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
560. [ 0.442441] alloc_chrdev_region: 249:0 ptp
561. [ 0.446745] PTP clock support registered
562. [ 0.450784] dmi: Firmware registration failed.
563. [ 0.455315] bman-fbpr addr 0x00000000f5000000 size 0x1000000
564. [ 0.461044] Bman err interrupt handler present
565. [ 0.466124] Bman portal initialised, cpu 0
566. [ 0.470332] Bman portal initialised, cpu 1
567. [ 0.474461] Bman portals initialised
568. [ 0.479224] Qman err interrupt handler present
569. [ 0.483941] QMan: Allocated lookup table at ffff000009fe5000, entry count 65537
570. [ 0.491883] Qman portal initialised, cpu 0
571. [ 0.496082] Qman portal initialised, cpu 1
572. [ 0.500209] Qman portals initialised
573. [ 0.503914] Bman: BPID allocator includes range 32:32
574. [ 0.509088] Qman: FQID allocator includes range 256:256
575. [ 0.514352] Qman: FQID allocator includes range 32768:32768
576. [ 0.520048] Qman: CGRID allocator includes range 0:256
577. [ 0.525426] Qman: pool channel allocator includes range 1025:15
578. [ 0.531519] No USDPAA memory, no 'fsl,usdpaa-mem' in device-tree
579. [ 0.537610] fsl-ifc 1530000.ifc: Freescale Integrated Flash Controller
580. [ 0.544200] fsl-ifc 1530000.ifc: IFC version 1.4, 8 banks
581. [ 0.549880] alloc_chrdev_region: 248:0 iio
582. [ 0.554647] alloc_chrdev_region: 247:0 watchdog
583. [ 0.559535] clocksource: Switched to clocksource arch_sys_counter
584. [ 0.565854] pnp: PnP ACPI: disabled
585. [ 0.573486] NET: Registered protocol family 2
586. [ 0.578266] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
587. [ 0.585671] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
588. [ 0.592588] TCP: Hash tables configured (established 16384 bind 16384)
589. [ 0.599244] UDP hash table entries: 1024 (order: 3, 32768 bytes)
590. [ 0.605342] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
591. [ 0.611968] NET: Registered protocol family 1
592. [ 0.616375] PCI: CLS 0 bytes, default 64
593. [ 0.834513] hw perfevents: failed to parse interrupt-affinity[2] for pmu
594. [ 0.841297] hw perfevents: /pmu: failed to register PMU devices!
595. [ 0.847369] armv8-pmu: probe of pmu failed with error -22
596. [ 0.858866] audit: initializing netlink subsys (disabled)
597. [ 0.864388] audit: type=2000 audit(0.740:1): state=initialized audit_enabled=0 res=1
598. [ 0.864730] workingset: timestamp_bits=62 max_order=19 bucket_order=0
599. [ 1.051949] alg: No test for fips(ansi_cprng) (fips_ansi_cprng)
600. [ 1.061374] async_tx: api initialized (async)
601. [ 1.065808] alloc_chrdev_region: 246:0 bsg
602. [ 1.070118] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
603. [ 1.077582] io scheduler noop registered
604. [ 1.081553] io scheduler cfq registered (default)
605. [ 1.086298] io scheduler mq-deadline registered
606. [ 1.090866] io scheduler kyber registered
607. [ 1.097205] OF: PCI: host bridge /soc/pcie@3400000 ranges:
608. [ 1.102804] OF: PCI: IO 0x4000010000..0x400001ffff -> 0x00000000
609. [ 1.109131] OF: PCI: MEM 0x4040000000..0x407fffffff -> 0x40000000
610. [ 1.115623] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0000:00
611. [ 1.122388] pci_bus 0000:00: root bus resource [bus 00-ff]
612. [ 1.127923] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
613. [ 1.134154] pci_bus 0000:00: root bus resource [mem 0x4040000000-0x407fffffff] (bus address [0x40000000-0x7fffffff])
614. [ 1.144777] pci 0000:00:00.0: [1957:8088] type 01 class 0x060400
615. [ 1.150855] pci 0000:00:00.0: reg 0x38: [mem 0x4040000000-0x40400007ff pref]
616. [ 1.157993] pci 0000:00:00.0: supports D1 D2
617. [ 1.162298] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
618. [ 1.168583] pci 0000:00:00.0: BAR 6: assigned [mem 0x4040000000-0x40400007ff pref]
619. [ 1.176217] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
620. [ 1.181676] pcieport 0000:00:00.0: Signaling PME with IRQ 70
621. [ 1.187482] pcieport 0000:00:00.0: AER enabled with IRQ 71
622. [ 1.193162] OF: PCI: host bridge /soc/pcie@3500000 ranges:
623. [ 1.198701] OF: PCI: IO 0x4800010000..0x480001ffff -> 0x00000000
624. [ 1.205024] OF: PCI: MEM 0x4840000000..0x487fffffff -> 0x40000000
625. [ 1.211458] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0001:00
626. [ 1.218220] pci_bus 0001:00: root bus resource [bus 00-ff]
627. [ 1.223752] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff])
628. [ 1.232784] pci_bus 0001:00: root bus resource [mem 0x4840000000-0x487fffffff] (bus address [0x40000000-0x7fffffff])
629. [ 1.243398] pci 0001:00:00.0: [1957:8088] type 01 class 0x060400
630. [ 1.249471] pci 0001:00:00.0: reg 0x38: [mem 0x4840000000-0x48400007ff pref]
631. [ 1.256598] pci 0001:00:00.0: supports D1 D2
632. [ 1.260905] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot
633. [ 1.267166] pci 0001:00:00.0: BAR 6: assigned [mem 0x4840000000-0x48400007ff pref]
634. [ 1.274802] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
635. [ 1.280229] pcieport 0001:00:00.0: Signaling PME with IRQ 72
636. [ 1.286032] pcieport 0001:00:00.0: AER enabled with IRQ 73
637. [ 1.293511] Freescale LS2 console driver
638. [ 1.297477] misc_register: 10, 62 fsl_mc_console
639. [ 1.302265] fsl-ls2-console: device fsl_mc_console registered
640. [ 1.308058] misc_register: 10, 61 fsl_aiop_console
641. [ 1.313013] fsl-ls2-console: device fsl_aiop_console registered
642. [ 1.320981] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
643. [ 1.328515] console [ttyS0] disabled
644. [ 1.332155] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 39, base_baud = 18750000) is a 16550A
645. [ 1.341034] console [ttyS0] enabled
646. [ 1.341034] console [ttyS0] enabled
647. [ 1.348039] bootconsole [uart8250] disabled
648. [ 1.348039] bootconsole [uart8250] disabled
649. [ 1.356700] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 39, base_baud = 18750000) is a 16550A
650. [ 1.365754] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 40, base_baud = 18750000) is a 16550A
651. [ 1.374802] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 40, base_baud = 18750000) is a 16550A
652. [ 1.384082] alloc_chrdev_region: 245:0 ttyLP
653. [ 1.388753] misc_register: 10, 183 hw_random
654. [ 1.398277] brd: module loaded
655. [ 1.401347] misc_register: 10, 237 loop-control
656. [ 1.409774] loop: module loaded
657. [ 1.441748] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode
658. [ 1.450734] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
659. [ 1.461111] scsi host0: ahci-qoriq
660. [ 1.464662] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 52
661. [ 1.473692] fsl-quadspi 1550000.quadspi: mx25u3235f (4096 Kbytes)
662. [ 1.479872] 11 ofpart partitions found on MTD device 1550000.quadspi
663. [ 1.486242] Creating 11 MTD partitions on "1550000.quadspi":
664. [ 1.491915] 0x000000000000-0x000000200000 : "NOR (RO) RCW + E-Hole + U-boot Image"
665. [ 1.499951] 0x000000200000-0x000000210000 : "NOR (RW) U-Boot ENV"
666. [ 1.506475] 0x000000210000-0x000000220000 : "NOR (RO) EMPTY Hole 1"
667. [ 1.513161] 0x000000220000-0x000000240000 : "NOR (RW) FMAN UCODE"
668. [ 1.519701] 0x000000240000-0x000000280000 : "NOR (RW) E-HOLE 2 or PPA"
669. [ 1.526636] 0x000000280000-0x0000002a0000 : "NOR (RW) WG CFG0"
670. [ 1.532883] 0x0000002a0000-0x0000002c0000 : "NOR (RW) WG CFG1"
671. [ 1.539137] 0x0000002c0000-0x0000002e0000 : "NOR (RW) WG MFG"
672. [ 1.545312] 0x0000002e0000-0x000000300000 : "NOR (RW) E-HOLE 3"
673. [ 1.551660] 0x000000300000-0x000000320000 : "NOR (RW) FMAN UCODE Old"
674. [ 1.558531] 0x000000320000-0x000000400000 : "NOR (RW) WG bootOpt Data & reserved"
675. [ 1.567520] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff
676. [ 1.574731] libphy: Fixed MDIO Bus: probed
677. [ 1.579900] libphy: Freescale XGMAC MDIO Bus: probed
678. [ 1.586306] libphy: Freescale XGMAC MDIO Bus: probed
679. [ 1.591841] libphy: Freescale XGMAC MDIO Bus: probed
680. [ 1.597119] libphy: Freescale XGMAC MDIO Bus: probed
681. [ 1.602412] libphy: Freescale XGMAC MDIO Bus: probed
682. [ 1.607698] libphy: Freescale XGMAC MDIO Bus: probed
683. [ 1.612970] libphy: Freescale XGMAC MDIO Bus: probed
684. [ 1.618247] libphy: Freescale XGMAC MDIO Bus: probed
685. [ 1.623517] libphy: Freescale XGMAC MDIO Bus: probed
686. [ 1.644196] Freescale FM module, FMD API version 21.1.0
687. [ 1.652780] Freescale FM Ports module
688. [ 1.656456] fsl_mac: fsl_mac: FSL FMan MAC API based driver
689. [ 1.662353] fman_memac_init: IF_MODE 2
690. [ 1.666629] fsl_mac 1ae0000.ethernet: FMan MEMAC
691. [ 1.671261] fsl_mac 1ae0000.ethernet: FMan MAC address: 00:0b:6b:01:01:01
692. [ 1.678216] fman_memac_init: IF_MODE 2
693. [ 1.682483] fsl_mac 1ae2000.ethernet: FMan MEMAC
694. [ 1.687116] fsl_mac 1ae2000.ethernet: FMan MAC address: 00:0b:6b:01:01:02
695. [ 1.694073] fman_memac_init: IF_MODE 8006
696. [ 1.698099] fsl_mac 1ae4000.ethernet: FMan MEMAC
697. [ 1.702729] fsl_mac 1ae4000.ethernet: FMan MAC address: 00:0b:6b:01:01:03
698. [ 1.709696] fman_memac_init: IF_MODE 2
699. [ 1.713964] fsl_mac 1ae8000.ethernet: FMan MEMAC
700. [ 1.718595] fsl_mac 1ae8000.ethernet: FMan MAC address: 00:0b:6b:01:01:05
701. [ 1.725559] fman_memac_init: IF_MODE 2
702. [ 1.729830] fsl_mac 1aea000.ethernet: FMan MEMAC
703. [ 1.734459] fsl_mac 1aea000.ethernet: FMan MAC address: 00:0b:6b:01:01:06
704. [ 1.741326] fsl_dpa: FSL DPAA Ethernet driver
705. [ 1.746657] fsl_dpa soc:fsl,dpaa:ethernet@0: Skip RX PCD High Priority FQs initialization
706. [ 1.758936] fsl_dpa: fsl_dpa: Probed interface eth0
707. [ 1.765223] fsl_dpa soc:fsl,dpaa:ethernet@1: Skip RX PCD High Priority FQs initialization
708. [ 1.777829] fsl_dpa: fsl_dpa: Probed interface eth1
709. [ 1.784791] fsl_dpa soc:fsl,dpaa:ethernet@2: Skip RX PCD High Priority FQs initialization
710. [ 1.788450] ata1: SATA link down (SStatus 0 SControl 300)
711. [ 1.803313] fsl_dpa: fsl_dpa: Probed interface eth2
712. [ 1.808901] fsl_dpa soc:fsl,dpaa:ethernet@3: of_find_device_by_node(/soc/fman@1a00000/ethernet@e6000) failed
713. [ 1.818771] fsl_dpa: probe of soc:fsl,dpaa:ethernet@3 failed with error -22
714. [ 1.826961] fsl_dpa soc:fsl,dpaa:ethernet@4: Skip RX PCD High Priority FQs initialization
715. [ 1.840794] fsl_dpa: fsl_dpa: Probed interface eth3
716. [ 1.847282] fsl_dpa soc:fsl,dpaa:ethernet@5: Skip RX PCD High Priority FQs initialization
717. [ 1.861138] fsl_dpa: fsl_dpa: Probed interface eth4
718. [ 1.867107] fsl_dpa soc:fsl,dpaa:ethernet@8: of_find_device_by_node(/soc/fman@1a00000/ethernet@f0000) failed
719. [ 1.876979] fsl_dpa: probe of soc:fsl,dpaa:ethernet@8 failed with error -22
720. [ 1.883993] fsl_advanced: FSL DPAA Advanced drivers:
721. [ 1.889621] fsl_proxy: FSL DPAA Proxy initialization driver
722. [ 1.895483] fsl_oh: FSL FMan Offline Parsing port driver
723. [ 1.903434] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
724. [ 1.909981] ehci-pci: EHCI PCI platform driver
725. [ 1.914515] ehci-platform: EHCI generic platform driver
726. [ 1.919977] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
727. [ 1.926174] ohci-pci: OHCI PCI platform driver
728. [ 1.930660] ohci-platform: OHCI generic platform driver
729. [ 1.936598] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
730. [ 1.942114] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
731. [ 1.950263] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x22010810
732. [ 1.959014] xhci-hcd xhci-hcd.0.auto: irq 49, io mem 0x02f00000
733. [ 1.965304] hub 1-0:1.0: USB hub found
734. [ 1.969083] hub 1-0:1.0: 1 port detected
735. [ 1.973237] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
736. [ 1.978745] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
737. [ 1.986420] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
738. [ 1.993378] hub 2-0:1.0: USB hub found
739. [ 1.997150] hub 2-0:1.0: 1 port detected
740. [ 2.001376] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
741. [ 2.006884] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
742. [ 2.014937] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x22010810
743. [ 2.023676] xhci-hcd xhci-hcd.1.auto: irq 50, io mem 0x03000000
744. [ 2.029913] hub 3-0:1.0: USB hub found
745. [ 2.033686] hub 3-0:1.0: 1 port detected
746. [ 2.037831] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
747. [ 2.043336] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
748. [ 2.051019] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
749. [ 2.057968] hub 4-0:1.0: USB hub found
750. [ 2.061744] hub 4-0:1.0: 1 port detected
751. [ 2.065959] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
752. [ 2.071470] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 5
753. [ 2.079619] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x22010810
754. [ 2.088356] xhci-hcd xhci-hcd.2.auto: irq 51, io mem 0x03100000
755. [ 2.094588] hub 5-0:1.0: USB hub found
756. [ 2.098361] hub 5-0:1.0: 1 port detected
757. [ 2.102498] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
758. [ 2.108058] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 6
759. [ 2.115737] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
760. [ 2.122682] hub 6-0:1.0: USB hub found
761. [ 2.126459] hub 6-0:1.0: 1 port detected
762. [ 2.130759] usbcore: registered new interface driver usbserial
763. [ 2.136637] usbcore: registered new interface driver usbserial_generic
764. [ 2.143243] usbserial: USB Serial support registered for generic
765. [ 2.149294] usbcore: registered new interface driver pl2303
766. [ 2.154898] usbserial: USB Serial support registered for pl2303
767. [ 2.170391] rtc-s35390a 0-0030: rtc core: registered rtc-s35390a as rtc0
768. [ 2.177168] i2c /dev entries driver
769. [ 2.180984] ptp_qoriq: device tree node missing required elements, try automatic configuration
770. [ 2.189867] pps pps0: new PPS source ptp0
771. [ 2.195173] misc_register: 10, 130 watchdog
772. [ 2.199474] imx2-wdt 2ad0000.wdog: timeout 60 sec (nowayout=0)
773. [ 2.205487] CPUidle arm: CPU 0 failed to init idle CPU ops
774. [ 2.211282] sdhci: Secure Digital Host Controller Interface driver
775. [ 2.217477] sdhci: Copyright(c) Pierre Ossman
776. [ 2.221943] sdhci-pltfm: SDHCI platform and OF driver helper
777. [ 2.271569] mmc0: SDHCI controller on 1560000.esdhc [1560000.esdhc] using ADMA 64-bit
778. [ 2.283419] ledtrig-cpu: registered to indicate activity on CPUs
779. [ 2.291040] platform caam_qi: Linux CAAM Queue I/F driver initialised
780. [ 2.297602] caam-dma caam-dma: Defer probing after JR driver probing
781. [ 2.304042] caam 1700000.crypto: Entropy delay = 3200
782. [ 2.309160] caam 1700000.crypto: Instantiated RNG4 SH0
783. [ 2.335896] caam 1700000.crypto: Instantiated RNG4 SH1
784. [ 2.341069] caam 1700000.crypto: device ID = 0x0a12060000000000 (Era 8)
785. [ 2.347729] caam 1700000.crypto: job rings = 3, qi = 1
786. [ 2.354400] usbcore: registered new interface driver usbhid
787. [ 2.359987] usbhid: USB HID core driver
788. [ 2.364835] Freescale USDPAA process driver
789. [ 2.368627] mmc0: new high speed MMC card at address 0001
790. [ 2.371569] mmcblk0: mmc0:0001 M62704 3.56 GiB
791. [ 2.371661] mmcblk0boot0: mmc0:0001 M62704 partition 1 2.00 MiB
792. [ 2.371805] mmcblk0boot1: mmc0:0001 M62704 partition 2 2.00 MiB
793. [ 2.371898] mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB
794. [ 2.373850] mmcblk0: p1 p2 p3 p4 < p5 p6 p7 >
795. [ 2.401030] fsl-usdpaa: no region found
796. [ 2.404930] Freescale USDPAA process IRQ driver
797. [ 2.409475] misc_register: 10, 60 fsl-usdpaa-irq
798. [ 2.414707] Initializing XFRM netlink socket
799. [ 2.419072] NET: Registered protocol family 10
800. [ 2.424364] Segment Routing with IPv6
801. [ 2.428086] ip6_tables: (C) 2000-2006 Netfilter Core Team
802. [ 2.433499] NET: Registered protocol family 17
803. [ 2.437962] NET: Registered protocol family 15
804. [ 2.442425] Key type ceph registered
805. [ 2.446086] libceph: loaded (mon/osd proto 15/24)
806. [ 2.450926] misc_register: 10, 59 cpu_dma_latency
807. [ 2.455782] misc_register: 10, 58 network_latency
808. [ 2.460632] misc_register: 10, 57 network_throughput
809. [ 2.465753] misc_register: 10, 56 memory_bandwidth
810. [ 2.470703] registered taskstats version 1
811. [ 2.475698] caam-dma caam-dma: caam dma support with 3 job rings
812. [ 2.483150] rtc-s35390a 0-0030: setting system clock to 2022-04-25 10:05:58 UTC (1650881158)
813. [ 2.494260] Freeing unused kernel memory: 5376K
814. [ 3.084465] random: crng init done
815. [ 5.027072] EXT4-fs (mmcblk0p5): mounting ext3 file system using the ext4 subsystem
816. [ 5.035397] EXT4-fs (mmcblk0p5): INFO: recovery required on readonly filesystem
817. [ 5.042722] EXT4-fs (mmcblk0p5): write access will be enabled during recovery
818. [ 5.410427] EXT4-fs (mmcblk0p5): recovery complete
819. [ 5.416399] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts:
820. initrd: Integrity check bypassed
821. [ 7.048396] Running /etc/runlevel/1/S02rootrw...Done.
822. [ 7.050682] Running /etc/runlevel/1/S05mproc...Done.
823. [ 7.051480] Running /etc/runlevel/1/S05sysfs...Done.
824. [ 7.052223] Running /etc/runlevel/1/S06fixdev...Done.
825. [ 7.053352] Running /etc/runlevel/1/S06temp...Done.
826. [ 7.054024] Running /etc/runlevel/1/S10armled...Done.
827. [ 7.064527] Running /etc/runlevel/1/S10diskpt...Done.
828. [ 7.066763] Running /etc/runlevel/1/S18seed-random...Reseeded random generator
829. [ 7.069300] Done.
830. [ 7.081801] Running /etc/runlevel/2/S10var...Done.
831. [ 7.084428] Running /etc/runlevel/2/S11shm...Done.
832. [ 7.085629] Running /etc/runlevel/2/S13devpts...Done.
833. [ 7.086212] Running /etc/runlevel/2/S15hosts...Done.
834. [ 7.087221] Running /etc/runlevel/2/S16pending...mke2fs 1.44.1 (24-Mar-2018)
835. [ 7.152268] Discarding device blocks: done
836. [ 7.726127] Creating filesystem with 194560 4k blocks and 48672 inodes
837. [ 7.726382] Filesystem UUID: 6e57ea48-c21a-4ef0-881a-f07103ff8574
838. [ 7.726614] Superblock backups stored on blocks:
839. [ 7.726793] 32768, 98304, 163840
840. [ 7.726911]
841. [ 7.726952] Allocating group tables: done
842. [ 7.727241] Writing inode tables: done
843. [ 7.751702] Writing superblocks and filesystem accounting information: done
844. [ 8.466443]
845. [ 8.469685] Done.
846. [ 8.469758] Running /etc/runlevel/2/S18data...fsck 1.44.1 (24-Mar-2018)
847. [ 8.490750] e2fsck 1.44.1 (24-Mar-2018)
848. [ 8.497891] /dev/wgrd.sysa_data: clean, 479/48672 files, 9416/194560 blocks
849. [ 7.723692] EXT4-fs (mmcblk0p5): mounting ext3 file system using the ext4 subsystem
850. [ 7.740861] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
851. [ 8.526511] Done.
852. [ 8.526591] Running /etc/runlevel/2/S18data2...fsck 1.44.1 (24-Mar-2018)
853. [ 8.532457] e2fsck 1.44.1 (24-Mar-2018)
854. [ 8.535284] /dev/wgrd.data2 was not cleanly unmounted, check forced.
855. [ 8.540258] Pass 1: Checking inodes, blocks, and sizes
856. [ 9.129105] Pass 2: Checking directory structure
857. [ 9.134894] Pass 3: Checking directory connectivity
858. [ 9.135100] Pass 4: Checking reference counts
859. [ 9.139965] Pass 5: Checking group summary information
860. [ 9.157749] /dev/wgrd.data2: 12/48672 files (0.0% non-contiguous), 3257/194560 blocks
861. [ 9.167170] Filesystem errors corrected.
862. [ 9.167347] Done.
863. [ 9.167407] Running /etc/runlevel/2/S18hotplug...Done.
864. [ 9.177323] Running /etc/runlevel/2/S18kdump...kdump T20/T40
865. [ 10.060715] Done.
866. [ 10.060830] Running /etc/runlevel/2/S19caam...
867. [ 9.308313] caam_jr 1710000.jr: registering rng-caam
868. [ 9.472856] alg: No test for auth(sha1) (auth-sha1-caam)
869. [ 9.478256] alg: No test for auth(sha256) (auth-sha256-caam)
870. [ 9.483984] alg: No test for auth(sha384) (auth-sha384-caam)
871. [ 9.489712] alg: No test for auth(sha512) (auth-sha512-caam)
872. [ 9.728901] alg: No test for authenc(hmac(sha224),ecb(cipher_null)) (authenc-hmac-sha224-ecb-cipher_null-caam)
873. [ 9.738991] alg: No test for authenc(hmac(sha256),ecb(cipher_null)) (authenc-hmac-sha256-ecb-cipher_null-caam)
874. [ 9.749068] alg: No test for authenc(hmac(sha384),ecb(cipher_null)) (authenc-hmac-sha384-ecb-cipher_null-caam)
875. [ 9.759148] alg: No test for authenc(hmac(sha512),ecb(cipher_null)) (authenc-hmac-sha512-ecb-cipher_null-caam)
876. [ 9.769221] alg: No test for authenc(hmac(md5),cbc(aes)) (authenc-hmac-md5-cbc-aes-caam)
877. [ 9.777389] alg: No test for echainiv(authenc(hmac(md5),cbc(aes))) (echainiv-authenc-hmac-md5-cbc-aes-caam)
878. [ 9.796958] alg: No test for echainiv(authenc(hmac(sha1),cbc(aes))) (echainiv-authenc-hmac-sha1-cbc-aes-caam)
879. [ 9.806955] alg: No test for authenc(hmac(sha224),cbc(aes)) (authenc-hmac-sha224-cbc-aes-caam)
880. [ 9.815641] alg: No test for echainiv(authenc(hmac(sha224),cbc(aes))) (echainiv-authenc-hmac-sha224-cbc-aes-caam)
881. [ 9.835731] alg: No test for echainiv(authenc(hmac(sha256),cbc(aes))) (echainiv-authenc-hmac-sha256-cbc-aes-caam)
882. [ 9.846073] alg: No test for authenc(hmac(sha384),cbc(aes)) (authenc-hmac-sha384-cbc-aes-caam)
883. [ 9.854758] alg: No test for echainiv(authenc(hmac(sha384),cbc(aes))) (echainiv-authenc-hmac-sha384-cbc-aes-caam)
884. [ 9.874852] alg: No test for echainiv(authenc(hmac(sha512),cbc(aes))) (echainiv-authenc-hmac-sha512-cbc-aes-caam)
885. [ 9.885193] alg: No test for authenc(hmac(md5),cbc(des3_ede)) (authenc-hmac-md5-cbc-des3_ede-caam)
886. [ 9.894229] alg: No test for echainiv(authenc(hmac(md5),cbc(des3_ede))) (echainiv-authenc-hmac-md5-cbc-des3_ede-caam)
887. [ 9.906387] alg: No test for echainiv(authenc(hmac(sha1),cbc(des3_ede))) (echainiv-authenc-hmac-sha1-cbc-des3_ede-caam)
888. [ 9.918724] alg: No test for echainiv(authenc(hmac(sha224),cbc(des3_ede))) (echainiv-authenc-hmac-sha224-cbc-des3_ede-caam)
889. [ 9.931405] alg: No test for echainiv(authenc(hmac(sha256),cbc(des3_ede))) (echainiv-authenc-hmac-sha256-cbc-des3_ede-caam)
890. [ 9.944152] alg: No test for echainiv(authenc(hmac(sha384),cbc(des3_ede))) (echainiv-authenc-hmac-sha384-cbc-des3_ede-caam)
891. [ 9.956843] alg: No test for echainiv(authenc(hmac(sha512),cbc(des3_ede))) (echainiv-authenc-hmac-sha512-cbc-des3_ede-caam)
892. [ 9.968055] alg: No test for authenc(hmac(md5),cbc(des)) (authenc-hmac-md5-cbc-des-caam)
893. [ 9.976221] alg: No test for echainiv(authenc(hmac(md5),cbc(des))) (echainiv-authenc-hmac-md5-cbc-des-caam)
894. [ 9.987513] alg: No test for echainiv(authenc(hmac(sha1),cbc(des))) (echainiv-authenc-hmac-sha1-cbc-des-caam)
895. [ 9.998984] alg: No test for echainiv(authenc(hmac(sha224),cbc(des))) (echainiv-authenc-hmac-sha224-cbc-des-caam)
896. [ 10.010795] alg: No test for echainiv(authenc(hmac(sha256),cbc(des))) (echainiv-authenc-hmac-sha256-cbc-des-caam)
897. [ 10.022614] alg: No test for echainiv(authenc(hmac(sha384),cbc(des))) (echainiv-authenc-hmac-sha384-cbc-des-caam)
898. [ 10.034433] alg: No test for echainiv(authenc(hmac(sha512),cbc(des))) (echainiv-authenc-hmac-sha512-cbc-des-caam)
899. [ 10.044776] alg: No test for authenc(hmac(md5),rfc3686(ctr(aes))) (authenc-hmac-md5-rfc3686-ctr-aes-caam)
900. [ 10.054425] alg: No test for seqiv(authenc(hmac(md5),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-md5-rfc3686-ctr-aes-caam)
901. [ 10.065258] alg: No test for seqiv(authenc(hmac(sha1),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha1-rfc3686-ctr-aes-caam)
902. [ 10.076209] alg: No test for authenc(hmac(sha224),rfc3686(ctr(aes))) (authenc-hmac-sha224-rfc3686-ctr-aes-caam)
903. [ 10.086377] alg: No test for seqiv(authenc(hmac(sha224),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha224-rfc3686-ctr-aes-caam)
904. [ 10.097733] alg: No test for seqiv(authenc(hmac(sha256),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha256-rfc3686-ctr-aes-caam)
905. [ 10.109089] alg: No test for seqiv(authenc(hmac(sha384),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha384-rfc3686-ctr-aes-caam)
906. [ 10.120439] alg: No test for seqiv(authenc(hmac(sha512),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha512-rfc3686-ctr-aes-caam)
907. [ 10.131691] caam algorithms registered in /proc/crypto
908. [ 10.203208] alg: No test for authenc(hmac(md5),cbc(aes)) (authenc-hmac-md5-cbc-aes-caam-qi)
909. [ 10.211660] alg: No test for echainiv(authenc(hmac(md5),cbc(aes))) (echainiv-authenc-hmac-md5-cbc-aes-caam-qi)
910. [ 10.224645] alg: No test for echainiv(authenc(hmac(sha1),cbc(aes))) (echainiv-authenc-hmac-sha1-cbc-aes-caam-qi)
911. [ 10.234913] alg: No test for authenc(hmac(sha224),cbc(aes)) (authenc-hmac-sha224-cbc-aes-caam-qi)
912. [ 10.243874] alg: No test for echainiv(authenc(hmac(sha224),cbc(aes))) (echainiv-authenc-hmac-sha224-cbc-aes-caam-qi)
913. [ 10.257379] alg: No test for echainiv(authenc(hmac(sha256),cbc(aes))) (echainiv-authenc-hmac-sha256-cbc-aes-caam-qi)
914. [ 10.267992] alg: No test for authenc(hmac(sha384),cbc(aes)) (authenc-hmac-sha384-cbc-aes-caam-qi)
915. [ 10.276954] alg: No test for echainiv(authenc(hmac(sha384),cbc(aes))) (echainiv-authenc-hmac-sha384-cbc-aes-caam-qi)
916. [ 10.290482] alg: No test for echainiv(authenc(hmac(sha512),cbc(aes))) (echainiv-authenc-hmac-sha512-cbc-aes-caam-qi)
917. [ 10.301093] alg: No test for authenc(hmac(md5),cbc(des3_ede)) (authenc-hmac-md5-cbc-des3_ede-caam-qi)
918. [ 10.310402] alg: No test for echainiv(authenc(hmac(md5),cbc(des3_ede))) (echainiv-authenc-hmac-md5-cbc-des3_ede-caam-qi)
919. [ 10.321862] alg: No test for echainiv(authenc(hmac(sha1),cbc(des3_ede))) (echainiv-authenc-hmac-sha1-cbc-des3_ede-caam-qi)
920. [ 10.333503] alg: No test for echainiv(authenc(hmac(sha224),cbc(des3_ede))) (echainiv-authenc-hmac-sha224-cbc-des3_ede-caam-qi)
921. [ 10.345491] alg: No test for echainiv(authenc(hmac(sha256),cbc(des3_ede))) (echainiv-authenc-hmac-sha256-cbc-des3_ede-caam-qi)
922. [ 10.357490] alg: No test for echainiv(authenc(hmac(sha384),cbc(des3_ede))) (echainiv-authenc-hmac-sha384-cbc-des3_ede-caam-qi)
923. [ 10.369483] alg: No test for echainiv(authenc(hmac(sha512),cbc(des3_ede))) (echainiv-authenc-hmac-sha512-cbc-des3_ede-caam-qi)
924. [ 10.380966] alg: No test for authenc(hmac(md5),cbc(des)) (authenc-hmac-md5-cbc-des-caam-qi)
925. [ 10.389410] alg: No test for echainiv(authenc(hmac(md5),cbc(des))) (echainiv-authenc-hmac-md5-cbc-des-caam-qi)
926. [ 10.400022] alg: No test for echainiv(authenc(hmac(sha1),cbc(des))) (echainiv-authenc-hmac-sha1-cbc-des-caam-qi)
927. [ 10.410801] alg: No test for echainiv(authenc(hmac(sha224),cbc(des))) (echainiv-authenc-hmac-sha224-cbc-des-caam-qi)
928. [ 10.421924] alg: No test for echainiv(authenc(hmac(sha256),cbc(des))) (echainiv-authenc-hmac-sha256-cbc-des-caam-qi)
929. [ 10.433050] alg: No test for echainiv(authenc(hmac(sha384),cbc(des))) (echainiv-authenc-hmac-sha384-cbc-des-caam-qi)
930. [ 10.444173] alg: No test for echainiv(authenc(hmac(sha512),cbc(des))) (echainiv-authenc-hmac-sha512-cbc-des-caam-qi)
931. [ 10.456643] platform caam_qi: algorithms registered in /proc/crypto
932. [ 10.529692] caam 1700000.crypto: caam pkc algorithms registered in /proc/crypto
933. Done.
934. [ 11.314703] Running /etc/runlevel/2/S19chkupgrade...Done.
935. [ 11.328491] Running /etc/runlevel/2/S19csfc_post...
936. [ 11.332630] CSfC Crypto self-test Bypassed
937. [ 11.332804] Done.
938. [ 11.332871] Running /etc/runlevel/2/S19ipv6...disabling IPv6 autoconf for all
939. [ 11.334503] disabling IPv6 autoconf for default
940. [ 11.334671] enable IPv6 forwarding for all
941. [ 11.334821] enable IPv6 forwarding for default
942. [ 11.334984] disabling IPv6 for all
943. [ 11.335105] disabling IPv6 for default
944. [ 11.335239] Done.
945. [ 11.335299] Running /etc/runlevel/2/S19platform...Done.
946. [ 11.336872] Running /etc/runlevel/2/S20adminhome...Done.
947. [ 11.343466] Running /etc/runlevel/2/S20cleanup-dbg...Done.
948. [ 11.349108] Running /etc/runlevel/2/S20cylanceconfig...Done.
949. [ 11.591415] Running /etc/runlevel/2/S20gwc...Done.
950. [ 11.592136] Running /etc/runlevel/2/S20sigs...unable to stat `/etc/defaults/signatures/dlp/PredefinedContentControlLists.xml' error No such file or directory
951. [ 11.604347] unable to stat `/etc/defaults/signatures/dlp/dlp_list.xml.gz' error No such file or directory
952. [ 11.604718] unable to stat `/etc/defaults/signatures/dlp/profile.xml' error No such file or directory
953. [ 10.852939] usbcore: registered new interface driver usb-storage
954. [ 11.614706] Done.
955. [ 11.614771] Running /etc/runlevel/2/S20tweakthermals...S20tweakthermals: model T20
956. [ 10.864457] wgipc: loading out-of-tree module taints kernel.
957. [ 10.870635] wgipc: module license 'Watchguard Proprietary' taints kernel.
958. [ 10.878751] Disabling lock debugging due to kernel taint
959. [ 10.885771] genl_validate_assign_mc_groups first_id set to 20 for WGIPC mc group
960. [ 11.619401] Setting Thermal Zone 0: trip_point_1_temp to 100C
961. [ 11.619631] Setting Thermal Zone 1: trip_point_1_temp to 100C
962. [ 11.619848] Setting Thermal Zone 2: trip_point_1_temp to 100C
963. [ 10.906670] dpaa2_evb: module is from the staging directory, the quality is unknown, you have been warned.
964. [ 11.620065] Setting Thermal Zone 3: trip_point_1_temp to 100C
965. [ 10.922286] fsl_dpa soc:fsl,dpaa:ethernet@0 eth0.tmp: renamed from eth0
966. [ 11.620298] Setting Thermal Zone 4: trip_point_1_temp to 100C
967. [ 11.620516] Done.
968. [ 10.939813] fsl_dpa soc:fsl,dpaa:ethernet@1 eth1.tmp: renamed from eth1
969. [ 11.620575] Running /etc/runlevel/2/S20usb...Done.
970. [ 11.637020] Running /etc/runlevel/2/S20wgbase...Done.
971. [ 11.676207] Running /etc/runlevel/2/S21eth...
972. [ 10.963788] fsl_dpa soc:fsl,dpaa:ethernet@2 eth0: renamed from eth2
973. [ 10.979786] fsl_dpa soc:fsl,dpaa:ethernet@0 eth1: renamed from eth0.tmp
974. [ 11.003776] fsl_dpa soc:fsl,dpaa:ethernet@1 eth2: renamed from eth1.tmp
975. Done.
976. [ 11.797180] Running /etc/runlevel/2/S21tpm_n_notpm...Done.
977. [ 11.801555] Running /etc/runlevel/2/S22hwmon...Done.
978. [ 11.804976] Running /etc/runlevel/2/S22login...Done.
979. [ 11.805399] Running /etc/runlevel/2/S22rtc...Done.
980. [ 11.811220] Running /etc/runlevel/2/S23pppoe...
981. [ 11.050071] PPP generic driver version 2.4.2
982. [ 11.065229] PPP MPPE Compression module registered
983. [ 11.073973] PPP Deflate Compression module registered
984. [ 11.082682] NET: Registered protocol family 24
985. Done.
986. [ 11.870510] Running /etc/runlevel/2/S23sslvpn...
987. [ 11.101764] tun: Universal TUN/TAP device driver, 1.6
988. [ 11.106913] misc_register: 10, 200 tun
989. Done.
990. [ 11.889231] Running /etc/runlevel/2/S23tpm...
991. [ 11.243555] tpm tpm0: starting up the TPM manually
992. S23tpm: Is a TPM DUT!
993. [ 12.390833] Done.
994. [ 12.390903] Running /etc/runlevel/2/S24fmcsetup...S24fmcsetup: model T20
995. [ 12.716598] Done.
996. [ 12.716672] Running /etc/runlevel/2/S24l2tpvpn...
997. [ 11.953823] l2tp_core: L2TP core driver, V2.0
998. [ 11.963303] l2tp_netlink: L2TP netlink interface
999. [ 11.973928] l2tp_ppp: PPPoL2TP kernel driver, V2.0
1000. Done.
1001. [ 12.756584] Running /etc/runlevel/2/S24nginx...Done.
1002. [ 12.759856] Running /etc/runlevel/2/S25core...Done.
1003. [ 12.760988] Running /etc/runlevel/2/S25wgcfg...Info: No conversion required from version 12.7.2 to 12.7.2.
1004. [ 13.167115] Done.
1005. [ 13.167197] Running /etc/runlevel/2/S26defaultxml...Done.
1006. [ 13.175807] Running /etc/runlevel/2/S27cfgcheck...Config ok
1007. [ 14.261126] Done.
1008. [ 14.261240] Running /etc/runlevel/2/S29wgcore...Done.
1009. [ 14.276947] Running /etc/runlevel/2/S30backup...Done.
1010. [ 14.278633] Running /etc/runlevel/2/S30net...
1011. [ 13.520869] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
1012. [ 13.539895] Bridge firewalling registered
1013. [ 13.550847] Ebtables v2.0 registered
1014. [ 13.710270] gre: GRE over IPv4 demultiplexor driver
1015. [ 13.727207] ip_gre: GRE over IPv4 tunneling driver
1016. [ 13.732570] register_netdevice: ifindex 7 -> iflink 0 gre0
1017. [ 13.738805] register_netdevice: ifindex 8 -> iflink 0 gretap0
1018. [ 13.745261] register_netdevice: ifindex 9 -> iflink 0 erspan0
1019. [ 13.751224] bvpn vif handlers are registered
1020. [ 13.762223] IPv4 over IPsec tunneling driver
1021. [ 13.767008] register_netdevice: ifindex 10 -> iflink 0 ip_vti0
1022. [ 13.785282] 8021q: 802.1Q VLAN Support v1.8
1023. [ 13.807214] register_netdevice: ifindex 11 -> iflink 0 ip6tnl0
1024. [ 13.820563] register_netdevice: ifindex 12 -> iflink 0 ip6_vti0
1025. [ 13.848116] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
1026. [ 13.854548] MII link monitoring set to 100 ms
1027. Done.
1028. [ 14.641946] Running /etc/runlevel/2/S30upgrade...Done.
1029. [ 14.644232] Running /etc/runlevel/2/S30wireless...start load wireless modules
1030. [ 14.647913] Done.
1031. [ 14.647976] Running /etc/runlevel/2/S31cacert...Done.
1032. [ 14.649671] Running /etc/runlevel/2/S31cert...Done.
1033. [ 14.678591] Running /etc/runlevel/2/S31crypto...Done.
1034. [ 14.690612] Running /etc/runlevel/2/S31xtables...[ 13.920023] Netfilter messages via NETLINK v0.30.
1035. [ 14.048550] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
1036. [ 14.054765] nf_conntrack_init_start: conntrack max=65536 high water mark=52428
1037. [ 14.201885] ip_tables: (C) 2000-2006 Netfilter Core Team
1038. [ 14.392327] nf_ct_ftp: Maximum expected value 1
1039. [ 14.487369] ctnetlink v0.93: registering with nfnetlink.
1040. [ 14.660955] arp_tables: arp_tables: (C) 2002 David S. Miller
1041. [ 14.754534] u32 classifier
1042. [ 14.757319] input device check on
1043. [ 14.760997] Actions configured
1044. [ 14.782680] Mirror/redirect action on
1045. Done.
1046. [ 15.568871] Running /etc/runlevel/2/S31xtables6...Done.
1047. [ 15.896807] Running /etc/runlevel/2/S32auth...Done.
1048. [ 15.905271] Running /etc/runlevel/2/S32clst...Done.
1049. [ 15.933217] Running /etc/runlevel/2/S32modemdrivers...
1050. [ 15.177363] usbcore: registered new interface driver option
1051. [ 15.183120] usbserial: USB Serial support registered for GSM modem (1-port)
1052. [ 15.196100] usbcore: registered new interface driver wg_sierra
1053. [ 15.202034] usbserial: USB Serial support registered for Sierra USB modem
1054. [ 15.215711] usbcore: registered new interface driver cdc_acm
1055. [ 15.221411] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
1056. [ 15.234475] usbcore: registered new interface driver GobiSerial
1057. [ 15.240503] usbserial: USB Serial support registered for GobiSerial
1058. [ 15.246808] GobiSerial: 2013-10-08/NTGR_2.12:GobiSerial
1059. [ 15.270734] usbcore: registered new interface driver cdc_ether
1060. [ 15.282027] usbcore: registered new interface driver rndis_host
1061. [ 15.293518] usbcore: registered new interface driver sierra_net
1062. [ 15.309055] GobiNet: 2013-10-08/NTGR_2.21
1063. [ 15.313293] usbcore: registered new interface driver GobiNet
1064. [ 15.324704] usbcore: registered new interface driver cdc_wdm
1065. [ 15.338751] usbcore: registered new interface driver qmi_wwan
1066. [ 15.351448] usbcore: registered new interface driver cdc_ncm
1067. [ 15.361138] usbcore: registered new interface driver huawei_cdc_ncm
1068. Done.
1069. [ 16.145276] Running /etc/runlevel/2/S32wgxt...
1070. [ 15.409376] ipt_addrpairs_6 v0.1.0: Loading
1071. [ 15.421229] xt_session6 : Loading
1072. [ 15.424608] xt_session6 : Loaded limit 1000 hash 1024 WG IPC ID 184549376 (0x0B000000)
1073. [ 15.476562] ipt_addrpairs: ADDRPAIRS SCALE Set MAX 16384 Entry Max 16384
1074. [ 15.483321] ipt_addrpairs: v1.0.0 Loaded
1075. [ 15.493672] xt_ifset: Loaded with set limit 5000 and entry limit 5000
1076. [ 15.503850] xt_classify : Loaded
1077. [ 15.510763] xt_master: Loaded
1078. [ 15.517563] xt_MASTER: Loaded
1079. [ 15.524355] xt_WGTEE: Loaded
1080. [ 15.531434] Schedule: Loaded
1081. [ 15.538259] xt_POLICY: Loaded
1082. [ 15.544880] xt_policy : Loaded
1083. [ 15.551780] xt_EXPIRES: Loaded
1084. [ 15.558661] xt_IPPRECEDENCE: Loaded
1085. [ 15.574116] xt_PKTCACHE: Loaded
1086. [ 15.586784] xt_session : Loaded limit 1000 hash 1024 WG IPC ID 92274688 (0x05800000)
1087. [ 15.610186] xt_CONNCLASSIFY: Loaded
1088. [ 15.617431] xt_connclassify : Loaded
1089. [ 15.626233] xt_ipspoof : Loaded
1090. [ 15.714702] xt_LBDNAT: Loaded
1091. [ 15.725155] xt_MWAN: Loaded
1092. [ 15.736958] xt_psd: Loaded
1093. [ 15.743958] xt_ipsd: Loaded
1094. [ 15.751015] xt_ddos: Loaded
1095. [ 15.758713] xt_dos: Loaded
1096. [ 15.767965] xt_wgaccount: Allocated 117 policy counter block array
1097. [ 15.774220] xt_wgaccount: Allocated policy counter block 0 of size 4080 at ffff8000704a1000
1098. [ 15.782597] xt_wgaccount: Allocated policy counter block 1 of size 4080 at ffff800071f50000
1099. [ 15.790977] xt_wgaccount: Loaded
1100. [ 15.881976] xt_block : Loaded limit 1000 hash 1024 WG IPC ID 155189248
1101. [ 15.896213] xt_localroute: Loaded
1102. [ 15.907067] xt_duplicate: Loaded
1103. [ 15.923923] xt_WGCLASSIFY: Loaded
1104. [ 15.959116] xt_fqdn : Loading
1105. [ 15.962336] xt_fqdn : Loaded
1106. [ 15.975673] devsec : Loaded limit 1000 hash 1024 WGIPC ID 260046848 (0x0F800000)
1107. [ 15.989303] xt_geo: Loaded limit 300 hash 256 WGIPC ID 272629760 (0x10400000)
1108. [ 15.996549] xt_sdwan: Loaded
1109. [ 16.010403] xt_WGCT: Loaded
1110. Done.
1111. [ 16.809189] Running /etc/runlevel/2/S33appID...
1112. [ 16.089484] tdts: Passive init mode
1113. [ 16.097765] WG workqueue: Loaded
1114. [ 16.176697] DPI engine defaults: conn_max=4096 tcp_reasm=1 eva_enhance=1 ac_type=0
1115. [ 16.184288] DPI engine active configuration: conn_max=500000 tcp_reasm=0 eva_enhance=0 ac_type=0
1116. [ 16.198397] Init chrdev /dev/detector with major 190
1117. [ 16.203417] DPI engine version 2.0.30 965e09
1118. [ 16.207702] DPI engine initialization succeeded
1119. [ 16.243543] Loaded
1120. Done.
1121. [ 17.023424] Running /etc/runlevel/2/S35nropen...updated /proc/sys/fs/nr_open with new value: 2097152
1122. [ 16.255708] Proxy glue: Loaded 17:41:19 (248)
1123. [ 17.024521] Done.
1124. [ 17.024582] Running /etc/runlevel/2/S35proxy...Setting the proxy tmpfs size to size=457m.
1125. [ 17.291963] /usr/bin/pxyhelper returned 0
1126. [ 17.292119] Done.
1127. [ 17.292179] Running /etc/runlevel/2/S35scand...Done.
1128. [ 17.301707] Running /etc/runlevel/2/S36dynroute...Done.
1129. [ 17.302192] Running /etc/runlevel/2/S42notpm_restore...systemdata file not provided, defaulting to (/etc/wg/tcsd/lib/tpm/system.data)
1130. [ 17.323842] restoring
1131. [ 17.323924] restore complete: systemdata_payload restore OK, length:2352
1132. [ 17.324185] Dealing with tpm DUT
1133. [ 17.324302] Done.
1134. [ 17.324361] Running /etc/runlevel/2/S42ssh...Done.
1135. [ 17.326493] Running /etc/runlevel/2/S44sysb...Done.
1136. [ 17.344961] Running /etc/runlevel/2/S45clientless...Done.
1137. [ 17.345576] Running /etc/runlevel/2/S45portald...Done.
1138. [ 17.346995] Running /etc/runlevel/2/S50nettune...Setting IPv4 route garbage collection timeout to 2 minutes
1139. [ 17.347971] Setting promote_secondaries to 1
1140. [ 17.348129] Setting icmp_errors_use_inbound_ifaddr to 1
1141. [ 17.348325] Done.
1142. [ 17.348385] Running /etc/runlevel/2/S60daas...Done.
1143. [ 17.349697] Running /etc/runlevel/2/S80seed-random...Saved random seed
1144. [ 17.356407] Done.
1145. [ 17.356470] Running /etc/runlevel/2/S90bootmon...Done.
1146. [ 17.359683] Running /etc/runlevel/2/S90kcrashrep...Done.
1147. [ 17.391665] Running /etc/runlevel/2/S98setmacs...setting device eth0 to 00:01:21:2a:cf:f9
1148. [ 17.402787] setting device eth1 to 00:01:21:2a:cf:fa
1149. [ 17.402988] setting device eth2 to 00:01:21:2a:cf:fb
1150. [ 17.403174] setting device eth3 to 00:01:21:2a:cf:fc
1151. [ 17.403366] setting device eth4 to 00:01:21:2a:cf:fd
1152. [ 17.403565] Done.
1153. [ 17.403625] Running /etc/runlevel/2/S99fetchmac0...Done.
1154. [ 17.406930] Running /etc/runlevel/2/S99igmp...Done.
1155. [ 17.407353] Running /etc/runlevel/2/S99rootro...Done.
1156. [ 20.735461] wg_ctmax_proc_dointvec: conntrack max=52600 high water mark=42080
1157. [ 22.164580] Running /etc/runlevel/4/S51armled...Done.
1158. [ 22.192068] Running /etc/runlevel/4/S81ckwebupload...Done.
1159. [ 22.213279] Running /etc/runlevel/4/S99defaultap...Not a wireless model, skipping script
1160. [ 22.219929] Done.
1161. ​
1162. smolguard login: