TIM-1.0 WTMI-armada-17.10.3-d61ed3a WTMI: system early-init DDR topology parameters: ======================== ddr type DDR3 ddr speedbin 12 bus width 16-bits cs num 2 cs[0] - group num 0 cs[0] - bank num 8 cs[0] - capacity 512MiB cs[1] - group num 0 cs[1] - bank num 8 cs[1] - capacity 512MiB DRAM windows: ============= WIN[0] - base addr 0x60000000 WIN[0] - size 0x40000000 WIN[1] - base addr 0xa0000000 WIN[1] - size 0x20000000 memory test region: =================== CS[0] 0x60000000 - 0x7fffffff CS[1] 0x80000000 - 0x9fffffff Fill memory before self refresh...done Fill memory before self refresh...done Now in Self-refresh Mode Restore termination values to original values Exited self-refresh ... Self refresh Pass. DDR self test mode test done!! Self refresh Pass. DDR self test mode test done!! QS GATING ============= Calibration done: cycle = 0x00 tap =0x5E CH0_PHY_RL_Control_CS0_B0[0xC0001180]: 0x0000005E CH0_PHY_RL_Control_CS0_B1[0xC0001184]: 0x0000005E QS GATING ============= Calibration done: cycle = 0x00 tap =0x5D CH0_PHY_RL_Control_CS1_B0[0xC00011A4]: 0x0000005D CH0_PHY_RL_Control_CS1_B1[0xC00011A8]: 0x0000005D DLL TUNING ============== DLL 0xc0001050[21:16]: [0,2f,17] DLL 0xc0001050[29:24]: [4,34,1c] DLL 0xc0001054[21:16]: [0,2b,15] DLL 0xc0001054[29:24]: [a,36,20] DLL 0xc0001074[21:16]: [0,3f,1f] DLL 0xc0001074NOTICE: Booting Trusted Firmware NOTICE: BL1: v1.3(debug):armada-17.10.7:16571d2 NOTICE: BL1: Built : 15:51:32, Apr 19 2NOTICE: BL2: v1.3(debug):armada-17.10.7:16571d2 NOTICE: BL2: Built : 15:51:34, Apr 19 2018NOTICE: BL31: v1.3(debug):armada-17.10.7:16571d2 NOTICE: BL31: U-Boot 2017.03-armada-17.10.1 (Dec 29 2018 - 11:26:46 +0800) Model: Marvell Armada 3720 ECK Board CPU @ 1000 [MHz] L2 @ 800 [MHz] TClock @ 200 [MHz] DDR @ 800 [MHz] DRAM: 1 GiB U-Boot DT blob at : 000000003f71b328 Comphy-0: USB3 5 Gbps Comphy-1: PEX0 2.5 Gbps Comphy-2: SATA0 6 Gbps MMC: sdhci@d8000: 0 SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB *** Warning - bad CRC, using default environment Net: SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB Factory mac is : B0-A7-B9-8E-EC-F1 eth0: neta@30000 [PRIME] Attach switch ID 0x004dd043 Attach switch driver for AR8236 Checking for firmware recovery mode... Reset button not pushed, do nothing Press CTRL+B to abort autoboot in 1 seconds switch to partitions #0, OK mmc0(part 0) is current device MMC read: dev # 0, block # 896, count 128 ... 128 blocks read: OK switch to partitions #0, OK mmc0(part 0) is current device MMC read: dev # 0, block # 1024, count 32768 ... 32768 blocks read: OK ## Flattened Device Tree blob at 04f00000 Booting using the fdt blob at 0x4f00000 Using Device Tree in place at 0000000004f00000, end 0000000004f05d72 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.109 (aholmes@astraea-lnx) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19375-77f278b3fbf) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Apr 7 09:12:29 2022 [ 0.000000] Machine model: TP-Link Omada OC200 [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '') [ 0.000000] printk: bootconsole [ar3700_uart0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] node 0: [mem 0x0000000004000000-0x00000000041fffff] [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 16 pages/cpu s28248 r8192 d29096 u65536 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048 [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000 mtdparts=spi0.0:1M(nor-flash) root=/dev/mmcblk0p1 rw rootwait [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1013808K/1048576K available (8384K kernel code, 954K rwdata, 2220K rodata, 512K init, 284K bss, 34768K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 192 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000 [ 0.000000] random: get_random_bytes called from start_kernel+0x3a8/0x57c with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns [ 0.008365] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000) [ 0.018960] pid_max: default: 32768 minimum: 301 [ 0.023812] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.031361] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.040694] rcu: Hierarchical SRCU implementation. [ 0.046048] EFI services will not be available. [ 0.050773] smp: Bringing up secondary CPUs ... [ 0.055776] Detected VIPT I-cache on CPU1 [ 0.055810] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000 [ 0.055854] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.055946] smp: Brought up 1 node, 2 CPUs [ 0.078004] SMP: Total of 2 processors activated. [ 0.082839] CPU features: detected: 32-bit EL0 Support [ 0.088130] CPU features: detected: CRC32 instructions [ 0.093449] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.102019] CPU: All CPU(s) started at EL2 [ 0.106232] alternatives: patching kernel code [ 0.113591] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.123680] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.130756] pinctrl core: initialized pinctrl subsystem [ 0.136595] DMI not present or invalid. [ 0.140953] NET: Registered protocol family 16 [ 0.145884] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.153131] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.161070] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.169571] thermal_sys: Registered thermal governor 'step_wise' [ 0.170062] cpuidle: using governor ladder [ 0.180557] ASID allocator initialised with 65536 entries [ 0.208220] cryptd: max_cpu_qlen set to 1000 [ 0.214571] SCSI subsystem initialized [ 0.218823] usbcore: registered new interface driver usbfs [ 0.224500] usbcore: registered new interface driver hub [ 0.229962] usbcore: registered new device driver usb [ 0.237396] clocksource: Switched to clocksource arch_sys_counter [ 0.244299] NET: Registered protocol family 2 [ 0.248922] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.257258] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.265834] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.273841] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.281324] TCP: Hash tables configured (established 8192 bind 8192) [ 0.287941] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.294698] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.302102] NET: Registered protocol family 1 [ 0.306525] PCI: CLS 0 bytes, default 64 [ 0.311928] workingset: timestamp_bits=46 max_order=18 bucket_order=0 [ 0.322057] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.328036] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.344279] mv_xor d0060900.xor: Marvell shared XOR driver [ 0.428057] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 0.518053] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 0.525740] debugfs: Directory 'd0060900.xor' with parent 'dmaengine' already present! [ 0.534026] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.541977] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.551988] loop: module loaded [ 0.557909] spi-nor spi0.0: gd25lq80c (1024 Kbytes) [ 0.563080] 1 fixed-partitions partitions found on MTD device spi0.0 [ 0.569698] Creating 1 MTD partitions on "spi0.0": [ 0.574548] 0x000000000000-0x000000100000 : "nor" [ 0.586555] mvneta: register 0x243c original value: 0 [ 0.591721] mvneta: register 0x243c modified value: 70000000 [ 0.598344] mvneta d0030000.ethernet eth0: Using random mac address 4a:ac:35:dd:23:db [ 0.606598] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.613290] ehci-pci: EHCI PCI platform driver [ 0.617890] ehci-platform: EHCI generic platform driver [ 0.623347] ehci-orion: EHCI orion driver [ 0.627714] orion-ehci d005e000.usb: EHCI Host Controller [ 0.633212] orion-ehci d005e000.usb: new USB bus registered, assigned bus number 1 [ 0.641125] orion-ehci d005e000.usb: irq 23, io mem 0xd005e000 [ 0.677432] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00 [ 0.683947] hub 1-0:1.0: USB hub found [ 0.687786] hub 1-0:1.0: 1 port detected [ 0.692843] usbcore: registered new interface driver usb-storage [ 0.699173] i2c /dev entries driver [ 0.703459] armada_37xx_wdt d0008300.watchdog: Initial timeout 120 sec [ 0.710648] sdhci: Secure Digital Host Controller Interface driver [ 0.716941] sdhci: Copyright(c) Pierre Ossman [ 0.721593] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.727547] leds-gpio leds: there is not valid maps for state default [ 0.735939] NET: Registered protocol family 10 [ 0.741500] Segment Routing with IPv6 [ 0.745246] NET: Registered protocol family 17 [ 0.749832] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.753655] mmc0: SDHCI controller on d00d8000.sdhci [d00d8000.sdhci] using ADMA [ 0.763325] 8021q: 802.1Q VLAN Support v1.8 [ 0.778831] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 0, base_baud = 1562500) is a mvebu-uart [ 0.788309] printk: console [ttyMV0] enabled [ 0.788309] printk: console [ttyMV0] enabled [ 0.797041] printk: bootconsole [ar3700_uart0] disabled [ 0.797041] printk: bootconsole [ar3700_uart0] disabled [ 0.834913] mmc0: new HS400 MMC card at address 0001 [ 0.840851] mmcblk0: mmc0:0001 4FTE4R 3.64 GiB [ 0.845818] mmcblk0boot0: mmc0:0001 4FTE4R partition 1 4.00 MiB [ 0.852252] mmcblk0boot1: mmc0:0001 4FTE4R partition 2 4.00 MiB [ 0.858486] mmcblk0rpmb: mmc0:0001 4FTE4R partition 3 512 KiB, chardev (249:0) [ 0.866689] mmcblk0: p1 p2 p3 p4 [ 0.870342] mmcblk0: p4 size 7200768 extends beyond EOD, truncated [ 2.814561] qca8k d0032004.mdio-mii:10: mib init failed [ 4.856530] qca8k d0032004.mdio-mii:10: configuring for fixed/rgmii link mode [ 4.867335] qca8k d0032004.mdio-mii:10: Link is Up - 100Mbps/Full - flow control off [ 4.875421] qca8k d0032004.mdio-mii:10 lan0 (uninitialized): PHY [d0032004.mdio-mii:00] driver [Generic PHY] (irq=POLL) [ 4.887722] qca8k d0032004.mdio-mii:10 lan1 (uninitialized): PHY [d0032004.mdio-mii:01] driver [Generic PHY] (irq=POLL) [ 4.916693] DSA: tree 0 setup [ 4.927007] xhci-hcd d0058000.usb: xHCI Host Controller [ 4.932445] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 2 [ 4.940204] xhci-hcd d0058000.usb: hcc params 0x0a000998 hci version 0x100 quirks 0x0000000000010090 [ 4.949678] xhci-hcd d0058000.usb: irq 22, io mem 0xd0058000 [ 4.956110] hub 2-0:1.0: USB hub found [ 4.960039] hub 2-0:1.0: 1 port detected [ 4.964326] xhci-hcd d0058000.usb: xHCI Host Controller [ 4.969766] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 3 [ 4.977418] xhci-hcd d0058000.usb: Host supports USB 3.0 SuperSpeed [ 4.983948] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.992718] hub 3-0:1.0: USB hub found [ 4.996621] hub 3-0:1.0: 1 port detected [ 5.001445] armada-37xx-rwtm-mailbox d00b0000.mailbox: Secure processor not ready [ 5.009212] turris-mox-rwtm firmware:armada-3700-rwtm: Cannot read board information: -5 [ 5.017579] armada-37xx-rwtm-mailbox d00b0000.mailbox: Secure processor not ready [ 5.025389] turris-mox-rwtm firmware:armada-3700-rwtm: Firmware does not support the GET_RANDOM command [ 5.035153] turris-mox-rwtm: probe of firmware:armada-3700-rwtm failed with error -5 [ 5.055684] VFS: Mounted root (squashfs filesystem) readonly on device 179:1. [ 5.064215] Freeing unused kernel memory: 512K [ 5.107526] Run /sbin/init as init process [ 5.311369] init: Console is alive [ 5.315050] init: - watchdog - [ 5.503802] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 5.524362] ehci-fsl: Freescale EHCI Host controller driver [ 5.533777] usbcore: registered new interface driver uas [ 5.539602] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.551244] init: - preinit - [ 5.758852] random: fast init done [ 5.922979] random: jshn: uninitialized urandom read (4 bytes read) [ 5.946263] random: jshn: uninitialized urandom read (4 bytes read) [ 5.971634] random: jshn: uninitialized urandom read (4 bytes read) [ 6.247328] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii link mode [ 6.256062] mvneta d0030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 6.266061] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.548523] urandom_read: 2 callbacks suppressed [ 10.548532] random: procd: uninitialized urandom read (4 bytes read) [ 10.611644] F2FS-fs (loop0): Mounted with checkpoint version = d70cadc [ 10.619228] mount_root: switching to f2fs overlay [ 10.625225] overlayfs: "xino" feature enabled using 32 upper inode bits. [ 10.661570] mmcblk0p1: Can't mount, would change RO state [ 10.669315] /dev/mmcblk0p1: Can't open blockdev mount: mounting /dev/mmcblk0p1 on /boot failed: Resource busy umount: can't unmount /boot: Invalid argument [ 10.745031] urandom-seed: Seeding 4096 bits and crediting [ 10.750762] random: crng init done [ 10.756197] urandom-seed: Saving 4096 bits of creditable seed for next boot [ 10.789532] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null) [ 11.810900] mvneta d0030000.ethernet eth0: TIMEOUT for TX stopped status=0x0000ff5d [ 21.821224] mvneta d0030000.ethernet eth0: TX FIFO empty timeout status=0x00010001 [ 21.829243] mvneta d0030000.ethernet eth0: Link is Down [ 21.852543] procd: - early - [ 21.855630] procd: - watchdog - Failed to connect to ubus [ 22.389339] procd: - watchdog - [ 22.394658] procd: - ubus - [ 22.555163] procd: - init - Please press Enter to activate this console. [ 22.867480] urngd: v1.0.2 started. [ 22.909996] kmodloader: loading kernel modules from /etc/modules.d/* [ 22.928980] zram: Added device: zram0 [ 22.957108] usbcore: registered new interface driver usbserial_generic [ 22.963985] usbserial: USB Serial support registered for generic [ 22.971165] usbcore: registered new interface driver ch341 [ 22.976910] usbserial: USB Serial support registered for ch341-uart [ 22.984494] usbcore: registered new interface driver cp210x [ 22.990400] usbserial: USB Serial support registered for cp210x [ 22.998164] usbcore: registered new interface driver ftdi_sio [ 23.004191] usbserial: USB Serial support registered for FTDI USB Serial Device [ 23.040996] kmodloader: done loading kernel modules from /etc/modules.d/* [ 26.446941] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii link mode [ 26.454932] mvneta d0030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 26.467912] br-lan: port 1(eth0) entered blocking state [ 26.473320] br-lan: port 1(eth0) entered disabled state [ 26.479009] device eth0 entered promiscuous mode [ 26.485937] br-lan: port 1(eth0) entered blocking state [ 26.491399] br-lan: port 1(eth0) entered forwarding state [ 27.467500] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready BusyBox v1.35.0 (2022-04-07 09:12:29 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt oc200, r19375-77f278b3fbf ----------------------------------------------------- root@oc200-dd7adf:/#