1. TIM-1.0
2. WTMI-armada-17.10.3-d61ed3a
3. WTMI: system early-init
4. ​
5. DDR topology parameters:
6. ========================
7. ddr type DDR3
8. ddr speedbin 12
9. bus width 16-bits
10. cs num 2
11. cs[0] - group num 0
12. cs[0] - bank num 8
13. cs[0] - capacity 512MiB
14. cs[1] - group num 0
15. cs[1] - bank num 8
16. cs[1] - capacity 512MiB
17. ​
18. DRAM windows:
19. =============
20. WIN[0] - base addr 0x60000000
21. WIN[0] - size 0x40000000
22. WIN[1] - base addr 0xa0000000
23. WIN[1] - size 0x20000000
24. ​
25. memory test region:
26. ===================
27. CS[0] 0x60000000 - 0x7fffffff
28. CS[1] 0x80000000 - 0x9fffffff
29. ​
30. Fill memory before self refresh...done
31. ​
32. Fill memory before self refresh...done
33. ​
34. Now in Self-refresh Mode
35. Restore termination values to original values
36. Exited self-refresh ...
37. ​
38. ​
39. Self refresh Pass.
40. DDR self test mode test done!!
41. ​
42. Self refresh Pass.
43. DDR self test mode test done!!
44. ​
45. QS GATING
46. =============
47. Calibration done: cycle = 0x00 tap =0x5E
48. CH0_PHY_RL_Control_CS0_B0[0xC0001180]: 0x0000005E
49. CH0_PHY_RL_Control_CS0_B1[0xC0001184]: 0x0000005E
50. ​
51. ​
52. QS GATING
53. =============
54. Calibration done: cycle = 0x00 tap =0x5D
55. CH0_PHY_RL_Control_CS1_B0[0xC00011A4]: 0x0000005D
56. CH0_PHY_RL_Control_CS1_B1[0xC00011A8]: 0x0000005D
57. ​
58. DLL TUNING
59. ==============
60. DLL 0xc0001050[21:16]: [0,2f,17]
61. DLL 0xc0001050[29:24]: [4,34,1c]
62. DLL 0xc0001054[21:16]: [0,2b,15]
63. DLL 0xc0001054[29:24]: [a,36,20]
64. DLL 0xc0001074[21:16]: [0,3f,1f]
65. DLL 0xc0001074NOTICE: Booting Trusted Firmware
66. NOTICE: BL1: v1.3(debug):armada-17.10.7:16571d2
67. NOTICE: BL1: Built : 15:51:32, Apr 19 2NOTICE: BL2: v1.3(debug):armada-17.10.7:16571d2
68. NOTICE: BL2: Built : 15:51:34, Apr 19 2018NOTICE: BL31: v1.3(debug):armada-17.10.7:16571d2
69. NOTICE: BL31:
70. ​
71. U-Boot 2017.03-armada-17.10.1 (Dec 29 2018 - 11:26:46 +0800)
72. ​
73. Model: Marvell Armada 3720 ECK Board
74. CPU @ 1000 [MHz]
75. L2 @ 800 [MHz]
76. TClock @ 200 [MHz]
77. DDR @ 800 [MHz]
78. DRAM: 1 GiB
79. U-Boot DT blob at : 000000003f71b328
80. Comphy-0: USB3 5 Gbps
81. Comphy-1: PEX0 2.5 Gbps
82. Comphy-2: SATA0 6 Gbps
83. MMC: sdhci@d8000: 0
84. SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB
85. *** Warning - bad CRC, using default environment
86. ​
87. Net: SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB
88. Factory mac is : B0-A7-B9-8E-EC-F1
89. eth0: neta@30000 [PRIME]
90. Attach switch ID 0x004dd043
91. Attach switch driver for AR8236
92. Checking for firmware recovery mode...
93. Reset button not pushed, do nothing
94. Press CTRL+B to abort autoboot in 1 seconds
95. switch to partitions #0, OK
96. mmc0(part 0) is current device
97. ​
98. MMC read: dev # 0, block # 896, count 128 ... 128 blocks read: OK
99. switch to partitions #0, OK
100. mmc0(part 0) is current device
101. ​
102. MMC read: dev # 0, block # 1024, count 32768 ... 32768 blocks read: OK
103. ## Flattened Device Tree blob at 04f00000
104. Booting using the fdt blob at 0x4f00000
105. Using Device Tree in place at 0000000004f00000, end 0000000004f05d72
106. ​
107. Starting kernel ...
108. ​
109. [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
110. [ 0.000000] Linux version 5.10.109 (aholmes@astraea-lnx) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19375-77f278b3fbf) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Apr 7 09:12:29 2022
111. [ 0.000000] Machine model: TP-Link Omada OC200
112. [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '')
113. [ 0.000000] printk: bootconsole [ar3700_uart0] enabled
114. [ 0.000000] efi: UEFI not found.
115. [ 0.000000] Zone ranges:
116. [ 0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff]
117. [ 0.000000] DMA32 empty
118. [ 0.000000] Normal empty
119. [ 0.000000] Movable zone start for each node
120. [ 0.000000] Early memory node ranges
121. [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
122. [ 0.000000] node 0: [mem 0x0000000004000000-0x00000000041fffff]
123. [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff]
124. [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
125. [ 0.000000] psci: probing for conduit method from DT.
126. [ 0.000000] psci: PSCIv1.0 detected in firmware.
127. [ 0.000000] psci: Using standard PSCI v0.2 function IDs
128. [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
129. [ 0.000000] psci: SMC Calling Convention v1.0
130. [ 0.000000] percpu: Embedded 16 pages/cpu s28248 r8192 d29096 u65536
131. [ 0.000000] Detected VIPT I-cache on CPU0
132. [ 0.000000] CPU features: detected: GIC system register CPU interface
133. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
134. [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000 mtdparts=spi0.0:1M(nor-flash) root=/dev/mmcblk0p1 rw rootwait
135. [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
136. [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
137. [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
138. [ 0.000000] Memory: 1013808K/1048576K available (8384K kernel code, 954K rwdata, 2220K rodata, 512K init, 284K bss, 34768K reserved, 0K cma-reserved)
139. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
140. [ 0.000000] rcu: Hierarchical RCU implementation.
141. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
142. [ 0.000000] Tracing variant of Tasks RCU enabled.
143. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
144. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
145. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
146. [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
147. [ 0.000000] GICv3: 192 SPIs implemented
148. [ 0.000000] GICv3: 0 Extended SPIs implemented
149. [ 0.000000] GICv3: Distributor has no Range Selector support
150. [ 0.000000] GICv3: 16 PPIs implemented
151. [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
152. [ 0.000000] random: get_random_bytes called from start_kernel+0x3a8/0x57c with crng_init=0
153. [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
154. [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
155. [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
156. [ 0.008365] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
157. [ 0.018960] pid_max: default: 32768 minimum: 301
158. [ 0.023812] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
159. [ 0.031361] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
160. [ 0.040694] rcu: Hierarchical SRCU implementation.
161. [ 0.046048] EFI services will not be available.
162. [ 0.050773] smp: Bringing up secondary CPUs ...
163. [ 0.055776] Detected VIPT I-cache on CPU1
164. [ 0.055810] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000
165. [ 0.055854] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
166. [ 0.055946] smp: Brought up 1 node, 2 CPUs
167. [ 0.078004] SMP: Total of 2 processors activated.
168. [ 0.082839] CPU features: detected: 32-bit EL0 Support
169. [ 0.088130] CPU features: detected: CRC32 instructions
170. [ 0.093449] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
171. [ 0.102019] CPU: All CPU(s) started at EL2
172. [ 0.106232] alternatives: patching kernel code
173. [ 0.113591] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
174. [ 0.123680] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
175. [ 0.130756] pinctrl core: initialized pinctrl subsystem
176. [ 0.136595] DMI not present or invalid.
177. [ 0.140953] NET: Registered protocol family 16
178. [ 0.145884] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
179. [ 0.153131] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
180. [ 0.161070] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
181. [ 0.169571] thermal_sys: Registered thermal governor 'step_wise'
182. [ 0.170062] cpuidle: using governor ladder
183. [ 0.180557] ASID allocator initialised with 65536 entries
184. [ 0.208220] cryptd: max_cpu_qlen set to 1000
185. [ 0.214571] SCSI subsystem initialized
186. [ 0.218823] usbcore: registered new interface driver usbfs
187. [ 0.224500] usbcore: registered new interface driver hub
188. [ 0.229962] usbcore: registered new device driver usb
189. [ 0.237396] clocksource: Switched to clocksource arch_sys_counter
190. [ 0.244299] NET: Registered protocol family 2
191. [ 0.248922] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
192. [ 0.257258] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
193. [ 0.265834] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
194. [ 0.273841] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
195. [ 0.281324] TCP: Hash tables configured (established 8192 bind 8192)
196. [ 0.287941] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
197. [ 0.294698] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
198. [ 0.302102] NET: Registered protocol family 1
199. [ 0.306525] PCI: CLS 0 bytes, default 64
200. [ 0.311928] workingset: timestamp_bits=46 max_order=18 bucket_order=0
201. [ 0.322057] squashfs: version 4.0 (2009/01/31) Phillip Lougher
202. [ 0.328036] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
203. [ 0.344279] mv_xor d0060900.xor: Marvell shared XOR driver
204. [ 0.428057] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
205. [ 0.518053] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
206. [ 0.525740] debugfs: Directory 'd0060900.xor' with parent 'dmaengine' already present!
207. [ 0.534026] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
208. [ 0.541977] cacheinfo: Unable to detect cache hierarchy for CPU 0
209. [ 0.551988] loop: module loaded
210. [ 0.557909] spi-nor spi0.0: gd25lq80c (1024 Kbytes)
211. [ 0.563080] 1 fixed-partitions partitions found on MTD device spi0.0
212. [ 0.569698] Creating 1 MTD partitions on "spi0.0":
213. [ 0.574548] 0x000000000000-0x000000100000 : "nor"
214. [ 0.586555] mvneta: register 0x243c original value: 0
215. [ 0.591721] mvneta: register 0x243c modified value: 70000000
216. [ 0.598344] mvneta d0030000.ethernet eth0: Using random mac address 4a:ac:35:dd:23:db
217. [ 0.606598] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
218. [ 0.613290] ehci-pci: EHCI PCI platform driver
219. [ 0.617890] ehci-platform: EHCI generic platform driver
220. [ 0.623347] ehci-orion: EHCI orion driver
221. [ 0.627714] orion-ehci d005e000.usb: EHCI Host Controller
222. [ 0.633212] orion-ehci d005e000.usb: new USB bus registered, assigned bus number 1
223. [ 0.641125] orion-ehci d005e000.usb: irq 23, io mem 0xd005e000
224. [ 0.677432] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00
225. [ 0.683947] hub 1-0:1.0: USB hub found
226. [ 0.687786] hub 1-0:1.0: 1 port detected
227. [ 0.692843] usbcore: registered new interface driver usb-storage
228. [ 0.699173] i2c /dev entries driver
229. [ 0.703459] armada_37xx_wdt d0008300.watchdog: Initial timeout 120 sec
230. [ 0.710648] sdhci: Secure Digital Host Controller Interface driver
231. [ 0.716941] sdhci: Copyright(c) Pierre Ossman
232. [ 0.721593] sdhci-pltfm: SDHCI platform and OF driver helper
233. [ 0.727547] leds-gpio leds: there is not valid maps for state default
234. [ 0.735939] NET: Registered protocol family 10
235. [ 0.741500] Segment Routing with IPv6
236. [ 0.745246] NET: Registered protocol family 17
237. [ 0.749832] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
238. [ 0.753655] mmc0: SDHCI controller on d00d8000.sdhci [d00d8000.sdhci] using ADMA
239. [ 0.763325] 8021q: 802.1Q VLAN Support v1.8
240. [ 0.778831] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 0, base_baud = 1562500) is a mvebu-uart
241. [ 0.788309] printk: console [ttyMV0] enabled
242. [ 0.788309] printk: console [ttyMV0] enabled
243. [ 0.797041] printk: bootconsole [ar3700_uart0] disabled
244. [ 0.797041] printk: bootconsole [ar3700_uart0] disabled
245. [ 0.834913] mmc0: new HS400 MMC card at address 0001
246. [ 0.840851] mmcblk0: mmc0:0001 4FTE4R 3.64 GiB
247. [ 0.845818] mmcblk0boot0: mmc0:0001 4FTE4R partition 1 4.00 MiB
248. [ 0.852252] mmcblk0boot1: mmc0:0001 4FTE4R partition 2 4.00 MiB
249. [ 0.858486] mmcblk0rpmb: mmc0:0001 4FTE4R partition 3 512 KiB, chardev (249:0)
250. [ 0.866689] mmcblk0: p1 p2 p3 p4
251. [ 0.870342] mmcblk0: p4 size 7200768 extends beyond EOD, truncated
252. [ 2.814561] qca8k d0032004.mdio-mii:10: mib init failed
253. [ 4.856530] qca8k d0032004.mdio-mii:10: configuring for fixed/rgmii link mode
254. [ 4.867335] qca8k d0032004.mdio-mii:10: Link is Up - 100Mbps/Full - flow control off
255. [ 4.875421] qca8k d0032004.mdio-mii:10 lan0 (uninitialized): PHY [d0032004.mdio-mii:00] driver [Generic PHY] (irq=POLL)
256. [ 4.887722] qca8k d0032004.mdio-mii:10 lan1 (uninitialized): PHY [d0032004.mdio-mii:01] driver [Generic PHY] (irq=POLL)
257. [ 4.916693] DSA: tree 0 setup
258. [ 4.927007] xhci-hcd d0058000.usb: xHCI Host Controller
259. [ 4.932445] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 2
260. [ 4.940204] xhci-hcd d0058000.usb: hcc params 0x0a000998 hci version 0x100 quirks 0x0000000000010090
261. [ 4.949678] xhci-hcd d0058000.usb: irq 22, io mem 0xd0058000
262. [ 4.956110] hub 2-0:1.0: USB hub found
263. [ 4.960039] hub 2-0:1.0: 1 port detected
264. [ 4.964326] xhci-hcd d0058000.usb: xHCI Host Controller
265. [ 4.969766] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 3
266. [ 4.977418] xhci-hcd d0058000.usb: Host supports USB 3.0 SuperSpeed
267. [ 4.983948] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
268. [ 4.992718] hub 3-0:1.0: USB hub found
269. [ 4.996621] hub 3-0:1.0: 1 port detected
270. [ 5.001445] armada-37xx-rwtm-mailbox d00b0000.mailbox: Secure processor not ready
271. [ 5.009212] turris-mox-rwtm firmware:armada-3700-rwtm: Cannot read board information: -5
272. [ 5.017579] armada-37xx-rwtm-mailbox d00b0000.mailbox: Secure processor not ready
273. [ 5.025389] turris-mox-rwtm firmware:armada-3700-rwtm: Firmware does not support the GET_RANDOM command
274. [ 5.035153] turris-mox-rwtm: probe of firmware:armada-3700-rwtm failed with error -5
275. [ 5.055684] VFS: Mounted root (squashfs filesystem) readonly on device 179:1.
276. [ 5.064215] Freeing unused kernel memory: 512K
277. [ 5.107526] Run /sbin/init as init process
278. [ 5.311369] init: Console is alive
279. [ 5.315050] init: - watchdog -
280. [ 5.503802] kmodloader: loading kernel modules from /etc/modules-boot.d/*
281. [ 5.524362] ehci-fsl: Freescale EHCI Host controller driver
282. [ 5.533777] usbcore: registered new interface driver uas
283. [ 5.539602] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
284. [ 5.551244] init: - preinit -
285. [ 5.758852] random: fast init done
286. [ 5.922979] random: jshn: uninitialized urandom read (4 bytes read)
287. [ 5.946263] random: jshn: uninitialized urandom read (4 bytes read)
288. [ 5.971634] random: jshn: uninitialized urandom read (4 bytes read)
289. [ 6.247328] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii link mode
290. [ 6.256062] mvneta d0030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
291. [ 6.266061] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
292. Press the [f] key and hit [enter] to enter failsafe mode
293. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
294. [ 10.548523] urandom_read: 2 callbacks suppressed
295. [ 10.548532] random: procd: uninitialized urandom read (4 bytes read)
296. [ 10.611644] F2FS-fs (loop0): Mounted with checkpoint version = d70cadc
297. [ 10.619228] mount_root: switching to f2fs overlay
298. [ 10.625225] overlayfs: "xino" feature enabled using 32 upper inode bits.
299. [ 10.661570] mmcblk0p1: Can't mount, would change RO state
300. [ 10.669315] /dev/mmcblk0p1: Can't open blockdev
301. mount: mounting /dev/mmcblk0p1 on /boot failed: Resource busy
302. umount: can't unmount /boot: Invalid argument
303. [ 10.745031] urandom-seed: Seeding 4096 bits and crediting
304. [ 10.750762] random: crng init done
305. [ 10.756197] urandom-seed: Saving 4096 bits of creditable seed for next boot
306. [ 10.789532] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
307. [ 11.810900] mvneta d0030000.ethernet eth0: TIMEOUT for TX stopped status=0x0000ff5d
308. [ 21.821224] mvneta d0030000.ethernet eth0: TX FIFO empty timeout status=0x00010001
309. [ 21.829243] mvneta d0030000.ethernet eth0: Link is Down
310. [ 21.852543] procd: - early -
311. [ 21.855630] procd: - watchdog -
312. Failed to connect to ubus
313. [ 22.389339] procd: - watchdog -
314. [ 22.394658] procd: - ubus -
315. [ 22.555163] procd: - init -
316. Please press Enter to activate this console.
317. [ 22.867480] urngd: v1.0.2 started.
318. [ 22.909996] kmodloader: loading kernel modules from /etc/modules.d/*
319. [ 22.928980] zram: Added device: zram0
320. [ 22.957108] usbcore: registered new interface driver usbserial_generic
321. [ 22.963985] usbserial: USB Serial support registered for generic
322. [ 22.971165] usbcore: registered new interface driver ch341
323. [ 22.976910] usbserial: USB Serial support registered for ch341-uart
324. [ 22.984494] usbcore: registered new interface driver cp210x
325. [ 22.990400] usbserial: USB Serial support registered for cp210x
326. [ 22.998164] usbcore: registered new interface driver ftdi_sio
327. [ 23.004191] usbserial: USB Serial support registered for FTDI USB Serial Device
328. [ 23.040996] kmodloader: done loading kernel modules from /etc/modules.d/*
329. [ 26.446941] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii link mode
330. [ 26.454932] mvneta d0030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
331. [ 26.467912] br-lan: port 1(eth0) entered blocking state
332. [ 26.473320] br-lan: port 1(eth0) entered disabled state
333. [ 26.479009] device eth0 entered promiscuous mode
334. [ 26.485937] br-lan: port 1(eth0) entered blocking state
335. [ 26.491399] br-lan: port 1(eth0) entered forwarding state
336. [ 27.467500] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
337. ​
338. ​
339. ​
340. BusyBox v1.35.0 (2022-04-07 09:12:29 UTC) built-in shell (ash)
341. ​
342. _______ ________ __
343. | |.-----.-----.-----.| | | |.----.| |_
344. | - || _ | -__| || | | || _|| _|
345. |_______|| __|_____|__|__||________||__| |____|
346. |__| W I R E L E S S F R E E D O M
347. -----------------------------------------------------
348. OpenWrt oc200, r19375-77f278b3fbf
349. -----------------------------------------------------
350. root@oc200-dd7adf:/#