- TIM-1.0
- WTMI-armada-17.10.3-d61ed3a
- WTMI: system early-init
-
- DDR topology parameters:
- ========================
- ddr type DDR3
- ddr speedbin 12
- bus width 16-bits
- cs num 2
- cs[0] - group num 0
- cs[0] - bank num 8
- cs[0] - capacity 512MiB
- cs[1] - group num 0
- cs[1] - bank num 8
- cs[1] - capacity 512MiB
-
- DRAM windows:
- =============
- WIN[0] - base addr 0x60000000
- WIN[0] - size 0x40000000
- WIN[1] - base addr 0xa0000000
- WIN[1] - size 0x20000000
-
- memory test region:
- ===================
- CS[0] 0x60000000 - 0x7fffffff
- CS[1] 0x80000000 - 0x9fffffff
-
- Fill memory before self refresh...done
-
- Fill memory before self refresh...done
-
- Now in Self-refresh Mode
- Restore termination values to original values
- Exited self-refresh ...
-
-
- Self refresh Pass.
- DDR self test mode test done!!
-
- Self refresh Pass.
- DDR self test mode test done!!
-
- QS GATING
- =============
- Calibration done: cycle = 0x00 tap =0x5C
- CH0_PHY_RL_Control_CS0_B0[0xC0001180]: 0x0000005C
- CH0_PHY_RL_Control_CS0_B1[0xC0001184]: 0x0000005C
-
-
- QS GATING
- =============
- Calibration done: cycle = 0x00 tap =0x5D
- CH0_PHY_RL_Control_CS1_B0[0xC00011A4]: 0x0000005D
- CH0_PHY_RL_Control_CS1_B1[0xC00011A8]: 0x0000005D
-
- DLL TUNING
- ==============
- DLL 0xc0001050[21:16]: [0,30,18]
- DLL 0xc0001050[29:24]: [3,32,1a]
- DLL 0xc0001054[21:16]: [0,2b,15]
- DLL 0xc0001054[29:24]: [9,33,1e]
- DLL 0xc0001074[21:16]: [0,3f,1f]
- DLL 0xc0001074NOTICE: Booting Trusted Firmware
- NOTICE: BL1: v1.3(debug):armada-17.10.7:16571d2
- NOTICE: BL1: Built : 15:51:32, Apr 19 2NOTICE: BL2: v1.3(debug):armada-17.10.7:16571d2
- NOTICE: BL2: Built : 15:51:34, Apr 19 2018NOTICE: BL31: v1.3(debug):armada-17.10.7:16571d2
- NOTICE: BL31:
-
- U-Boot 2017.03-armada-17.10.1 (Dec 29 2018 - 11:26:46 +0800)
-
- Model: Marvell Armada 3720 ECK Board
- CPU @ 1000 [MHz]
- L2 @ 800 [MHz]
- TClock @ 200 [MHz]
- DDR @ 800 [MHz]
- DRAM: 1 GiB
- U-Boot DT blob at : 000000003f71b328
- Comphy-0: USB3 5 Gbps
- Comphy-1: PEX0 2.5 Gbps
- Comphy-2: SATA0 6 Gbps
- MMC: sdhci@d8000: 0
- SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB
- *** Warning - bad CRC, using default environment
-
- Net: SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB
- Factory mac is : B0-A7-B9-8E-EC-F1
- eth0: neta@30000 [PRIME]
- Attach switch ID 0x004dd043
- Attach switch driver for AR8236
- Checking for firmware recovery mode...
- Reset button not pushed, do nothing
- Press CTRL+B to abort autoboot in 1 seconds
- switch to partitions #0, OK
- mmc0(part 0) is current device
-
- MMC read: dev # 0, block # 896, count 128 ... 128 blocks read: OK
- switch to partitions #0, OK
- mmc0(part 0) is current device
-
- MMC read: dev # 0, block # 1024, count 32768 ... 32768 blocks read: OK
- ## Flattened Device Tree blob at 04f00000
- Booting using the fdt blob at 0x4f00000
- Using Device Tree in place at 0000000004f00000, end 0000000004f05d72
-
- Starting kernel ...
-
- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
- [ 0.000000] Linux version 5.10.109 (aholmes@astraea-lnx) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19375-77f278b3fbf) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Apr 7 09:12:29 2022
- [ 0.000000] Machine model: TP-Link Omada OC200
- [ 0.000000] efi: EFI v2.05 by Das U-boot
- [ 0.000000] efi: SMBIOS=0x3bffa000
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] DMA32 empty
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
- [ 0.000000] node 0: [mem 0x0000000004000000-0x00000000041fffff]
- [ 0.000000] node 0: [mem 0x0000000004200000-0x0000000008003fff]
- [ 0.000000] node 0: [mem 0x0000000008005000-0x000000003bff9fff]
- [ 0.000000] node 0: [mem 0x000000003bffa000-0x000000003bffafff]
- [ 0.000000] node 0: [mem 0x000000003bffb000-0x000000003ffa7fff]
- [ 0.000000] node 0: [mem 0x000000003ffa8000-0x000000003ffa8fff]
- [ 0.000000] node 0: [mem 0x000000003ffa9000-0x000000003fffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
- [ 0.000000] On node 0, zone DMA: 1 pages in unavailable ranges
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.0 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- [ 0.000000] psci: SMC Calling Convention v1.0
- [ 0.000000] percpu: Embedded 16 pages/cpu s28248 r8192 d29096 u65536
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] CPU features: detected: GIC system register CPU interface
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258047
- [ 0.000000] Kernel command line: console=ttyMV0,115200
- [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
- [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
- [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
- [ 0.000000] Memory: 986268K/1048572K available (8384K kernel code, 954K rwdata, 2220K rodata, 28032K init, 284K bss, 62304K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
- [ 0.000000] rcu: Hierarchical RCU implementation.
- [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
- [ 0.000000] Tracing variant of Tasks RCU enabled.
- [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
- [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
- [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
- [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
- [ 0.000000] GICv3: 192 SPIs implemented
- [ 0.000000] GICv3: 0 Extended SPIs implemented
- [ 0.000000] GICv3: Distributor has no Range Selector support
- [ 0.000000] GICv3: 16 PPIs implemented
- [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
- [ 0.000000] random: get_random_bytes called from start_kernel+0x3a8/0x57c with crng_init=0
- [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
- [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
- [ 0.000107] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
- [ 0.000119] pid_max: default: 32768 minimum: 301
- [ 0.000238] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
- [ 0.000252] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
- [ 0.001538] rcu: Hierarchical SRCU implementation.
- [ 0.002013] Remapping and enabling EFI services.
- [ 0.002188] smp: Bringing up secondary CPUs ...
- [ 0.002569] Detected VIPT I-cache on CPU1
- [ 0.002603] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000
- [ 0.002647] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
- [ 0.002737] smp: Brought up 1 node, 2 CPUs
- [ 0.002752] SMP: Total of 2 processors activated.
- [ 0.002759] CPU features: detected: 32-bit EL0 Support
- [ 0.002765] CPU features: detected: CRC32 instructions
- [ 0.002801] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
- [ 0.002810] CPU: All CPU(s) started at EL2
- [ 0.002825] alternatives: patching kernel code
- [ 0.005474] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
- [ 0.005500] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
- [ 0.005608] pinctrl core: initialized pinctrl subsystem
- [ 0.006540] SMBIOS 3.0 present.
- [ 0.006575] DMI: Marvell mvebu_armada-37xx/mvebu_armada-37xx, BIOS 2017.03-armada-17.10.1 12/29/2018
- [ 0.007118] NET: Registered protocol family 16
- [ 0.007551] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
- [ 0.007598] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
- [ 0.007635] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
- [ 0.008003] thermal_sys: Registered thermal governor 'step_wise'
- [ 0.008677] cpuidle: using governor ladder
- [ 0.008763] ASID allocator initialised with 65536 entries
- [ 0.030912] cryptd: max_cpu_qlen set to 1000
- [ 0.032941] SCSI subsystem initialized
- [ 0.033622] usbcore: registered new interface driver usbfs
- [ 0.033669] usbcore: registered new interface driver hub
- [ 0.033715] usbcore: registered new device driver usb
- [ 0.034111] Registered efivars operations
- [ 0.035642] clocksource: Switched to clocksource arch_sys_counter
- [ 0.036318] NET: Registered protocol family 2
- [ 0.036464] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
- [ 0.037572] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
- [ 0.037612] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
- [ 0.037685] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
- [ 0.037821] TCP: Hash tables configured (established 8192 bind 8192)
- [ 0.037993] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
- [ 0.038030] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
- [ 0.038222] NET: Registered protocol family 1
- [ 0.038256] PCI: CLS 0 bytes, default 64
- [ 0.157865] workingset: timestamp_bits=46 max_order=18 bucket_order=0
- [ 0.161445] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.161463] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.168372] mv_xor d0060900.xor: Marvell shared XOR driver
- [ 0.226330] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
- [ 0.286258] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
- [ 0.286402] debugfs: Directory 'd0060900.xor' with parent 'dmaengine' already present!
- [ 0.286598] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.288028] cacheinfo: Unable to detect cache hierarchy for CPU 0
- [ 0.291936] loop: module loaded
- [ 0.295349] spi-nor spi0.0: gd25lq80c (1024 Kbytes)
- [ 0.300821] 1 fixed-partitions partitions found on MTD device spi0.0
- [ 0.300840] Creating 1 MTD partitions on "spi0.0":
- [ 0.300850] 0x000000000000-0x000000100000 : "nor"
- [ 0.317864] mvneta: register 0x243c original value: 70000000
- [ 0.317880] mvneta: register 0x243c modified value: 70000000
- [ 0.318680] mvneta d0030000.ethernet eth0: Using hardware mac address b0:a7:b9:8e:ec:f1
- [ 0.318939] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 0.318981] ehci-pci: EHCI PCI platform driver
- [ 0.319043] ehci-platform: EHCI generic platform driver
- [ 0.319203] ehci-orion: EHCI orion driver
- [ 0.319515] orion-ehci d005e000.usb: EHCI Host Controller
- [ 0.319548] orion-ehci d005e000.usb: new USB bus registered, assigned bus number 1
- [ 0.319678] orion-ehci d005e000.usb: irq 23, io mem 0xd005e000
- [ 0.345565] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00
- [ 0.346097] hub 1-0:1.0: USB hub found
- [ 0.346137] hub 1-0:1.0: 1 port detected
- [ 0.347142] usbcore: registered new interface driver usb-storage
- [ 0.347325] i2c /dev entries driver
- [ 0.348110] armada_37xx_wdt d0008300.watchdog: Initial timeout 120 sec
- [ 0.348584] sdhci: Secure Digital Host Controller Interface driver
- [ 0.348599] sdhci: Copyright(c) Pierre Ossman
- [ 0.348678] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 0.348840] leds-gpio leds: there is not valid maps for state default
- [ 0.351542] NET: Registered protocol family 10
- [ 0.352675] Segment Routing with IPv6
- [ 0.352755] NET: Registered protocol family 17
- [ 0.352825] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
- [ 0.352991] 8021q: 802.1Q VLAN Support v1.8
- [ 0.356564] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 0, base_baud = 1562500) is a mvebu-uart
- [ 0.375553] mmc0: SDHCI controller on d00d8000.sdhci [d00d8000.sdhci] using ADMA
- [ 0.381115] printk: console [ttyMV0] enabled
- [ 1.221435] mmc0: new HS400 MMC card at address 0001
- [ 1.227814] mmcblk0: mmc0:0001 4FTE4R 3.64 GiB
- [ 1.232771] mmcblk0boot0: mmc0:0001 4FTE4R partition 1 4.00 MiB
- [ 1.239421] mmcblk0boot1: mmc0:0001 4FTE4R partition 2 4.00 MiB
- [ 1.245653] mmcblk0rpmb: mmc0:0001 4FTE4R partition 3 512 KiB, chardev (249:0)
- [ 1.253776] mmcblk0: p1 p2 p3 p4
- [ 1.257428] mmcblk0: p4 size 7200768 extends beyond EOD, truncated
- [ 3.232492] qca8k d0032004.mdio-mii:10: mib init failed
- [ 5.274769] qca8k d0032004.mdio-mii:10: configuring for fixed/rgmii link mode
- [ 5.285599] qca8k d0032004.mdio-mii:10: Link is Up - 100Mbps/Full - flow control off
- [ 5.293673] qca8k d0032004.mdio-mii:10 lan0 (uninitialized): PHY [d0032004.mdio-mii:00] driver [Generic PHY] (irq=POLL)
- [ 5.306057] qca8k d0032004.mdio-mii:10 lan1 (uninitialized): PHY [d0032004.mdio-mii:01] driver [Generic PHY] (irq=POLL)
- [ 5.335852] DSA: tree 0 setup
- [ 5.345595] xhci-hcd d0058000.usb: xHCI Host Controller
- [ 5.351012] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 2
- [ 5.358800] xhci-hcd d0058000.usb: hcc params 0x0a000998 hci version 0x100 quirks 0x0000000000010090
- [ 5.368283] xhci-hcd d0058000.usb: irq 22, io mem 0xd0058000
- [ 5.374694] hub 2-0:1.0: USB hub found
- [ 5.378637] hub 2-0:1.0: 1 port detected
- [ 5.382920] xhci-hcd d0058000.usb: xHCI Host Controller
- [ 5.388350] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 3
- [ 5.395998] xhci-hcd d0058000.usb: Host supports USB 3.0 SuperSpeed
- [ 5.402533] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
- [ 5.411307] hub 3-0:1.0: USB hub found
- [ 5.415216] hub 3-0:1.0: 1 port detected
- [ 5.420038] armada-37xx-rwtm-mailbox d00b0000.mailbox: Secure processor not ready
- [ 5.427826] turris-mox-rwtm firmware:armada-3700-rwtm: Cannot read board information: -5
- [ 5.436189] armada-37xx-rwtm-mailbox d00b0000.mailbox: Secure processor not ready
- [ 5.443999] turris-mox-rwtm firmware:armada-3700-rwtm: Firmware does not support the GET_RANDOM command
- [ 5.453757] turris-mox-rwtm: probe of firmware:armada-3700-rwtm failed with error -5
- [ 5.539430] Freeing unused kernel memory: 28032K
- [ 5.575643] Run /init as init process
- [ 5.967341] init: Console is alive
- [ 5.971025] init: - watchdog -
- [ 5.983074] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 5.996937] ehci-fsl: Freescale EHCI Host controller driver
- [ 6.005804] usbcore: registered new interface driver uas
- [ 6.011554] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 6.025345] init: - preinit -
- [ 6.133970] random: jshn: uninitialized urandom read (4 bytes read)
- [ 6.171960] random: jshn: uninitialized urandom read (4 bytes read)
- [ 6.197471] random: jshn: uninitialized urandom read (4 bytes read)
- [ 6.259193] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii link mode
- [ 6.267891] mvneta d0030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
- [ 6.277488] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
-
- [ 9.643313] mvneta d0030000.ethernet eth0: TIMEOUT for TX stopped status=0x0000ff4e
- [ 19.655322] mvneta d0030000.ethernet eth0: TX FIFO empty timeout status=0x00010001
- [ 19.663351] mvneta d0030000.ethernet eth0: Link is Down
- [ 19.686963] procd: - early -
- [ 19.690045] procd: - watchdog -
- [ 19.773193] urandom_read: 2 callbacks suppressed
- [ 19.773200] random: jshn: uninitialized urandom read (4 bytes read)
- [ 19.865985] random: jshn: uninitialized urandom read (4 bytes read)
- [ 19.956337] random: jshn: uninitialized urandom read (4 bytes read)
- [ 20.224289] procd: - watchdog -
- [ 20.228222] procd: - ubus -
- [ 20.288964] procd: - init -
- Please press Enter to activate this console.
- [ 20.484584] urngd: v1.0.2 started.
- [ 20.522876] random: crng init done
- [ 20.526499] random: 2 urandom warning(s) missed due to ratelimiting
- [ 20.552155] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 20.562741] zram: Added device: zram0
- [ 20.591569] usbcore: registered new interface driver usbserial_generic
- [ 20.598420] usbserial: USB Serial support registered for generic
- [ 20.606813] usbcore: registered new interface driver ch341
- [ 20.612522] usbserial: USB Serial support registered for ch341-uart
- [ 20.620838] usbcore: registered new interface driver cp210x
- [ 20.626741] usbserial: USB Serial support registered for cp210x
- [ 20.635155] usbcore: registered new interface driver ftdi_sio
- [ 20.641190] usbserial: USB Serial support registered for FTDI USB Serial Device
- [ 20.688395] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 22.456694] [xx_custom] INFO: Applying custom default configuration
- [ 22.463496] [xx_custom] INFO: Setting hostname based on MAC address
- [ 22.478767] [xx_custom] PASSWD: Setting root password to send4help
- [ 22.491880] [xx_custom] INFO: Applying network configuration
- [ 29.928247] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii link mode
- [ 29.936198] mvneta d0030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
- [ 29.948283] br-lan: port 1(eth0) entered blocking state
- [ 29.953695] br-lan: port 1(eth0) entered disabled state
- [ 29.959432] device eth0 entered promiscuous mode
- [ 29.975659] br-lan: port 1(eth0) entered blocking state
- [ 29.981074] br-lan: port 1(eth0) entered forwarding state
- [ 30.965693] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
-
-
-
- BusyBox v1.35.0 (2022-04-07 09:12:29 UTC) built-in shell (ash)
-
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- OpenWrt oc200, r19375-77f278b3fbf
- -----------------------------------------------------
- root@oc200-8eecf1:/# ip a
- 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
- link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
- inet 127.0.0.1/8 scope host lo
- valid_lft forever preferred_lft forever
- inet6 ::1/128 scope host
- valid_lft forever preferred_lft forever
- 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1502 qdisc mq master br-lan state UP group default qlen 1024
- link/ether b0:a7:b9:8e:ec:f1 brd ff:ff:ff:ff:ff:ff
- 3: lan0@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
- link/ether b0:a7:b9:8e:ec:f1 brd ff:ff:ff:ff:ff:ff
- 4: lan1@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
- link/ether b0:a7:b9:8e:ec:f1 brd ff:ff:ff:ff:ff:ff
- 5: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1502 qdisc noqueue state UP group default qlen 1000
- link/ether b0:a7:b9:8e:ec:f1 brd ff:ff:ff:ff:ff:ff
- inet6 fe80::b2a7:b9ff:fe8e:ecf1/64 scope link
- valid_lft forever preferred_lft forever
- root@oc200-8eecf1:/#