Snippet content copied to clipboard.
Are you sure to delete this snippet? No, don't delete
  1. B - 61061 - SBL1, Start
  2. B - 61091 - scatterload_region && ram_init, Start
  3. D - 30 - scatterload_region && ram_init, Delta
  4. B - 72071 - Enable tsens
  5. B - 72590 - tsensResult:=0 tsensTemp:=28
  6. B - 72986 - Clock_BranchEnable
  7. B - 76219 - Clock_MuxInit
  8. B - 78842 - pm_device_init, Start
  9. B - 82075 - boot_fsm_cdt_init, Start
  10. D - 356026 - boot_fsm_cdt_init, Delta
  11. B - 441701 - pm_fsm9055pdm_config
  12. B - 442189 - boot_pm_driver_init, Start
  13. B - 446032 - Clock_BranchEnable
  14. B - 449082 - Clock_MuxInit
  15. D - 5673 - boot_pm_driver_init, Delta
  16. B - 455456 - pm_set_based_on_mode, Start
  17. D - 30 - pm_set_based_on_mode, Delta
  18. B - 463051 - pm_adjust_based_on_cpr, Start
  19. D - 30 - pm_adjust_based_on_cpr, Delta
  20. P - 1127 - pm_get_cx_vout (mv)
  21. D - 0 - pm_device_init, Delta
  22. B - 477508 - clock_init, Start
  23. D - 26443 - clock_init, Delta
  24. B - 507306 - boot_flash_init, Start
  25. D - 985089 - boot_flash_init, Delta
  26. B - 1492487 - boot_set_partition_id, Start
  27. D - 91 - boot_set_partition_id, Delta
  28. B - 1497458 - boot_fsm_cdt_init, Start
  29. D - 146491 - boot_fsm_cdt_init, Delta
  30. B - 1647518 - sbl1_hw_platform_pre_ddr, Start
  31. D - 0 - sbl1_hw_platform_pre_ddr, Delta
  32. B - 1653222 - sbl1_ddr_set_params, Start
  33. D - 762 - sbl1_ddr_set_params, Delta
  34. B - 1660664 - sbl1_ddr_init, Start
  35. B - 1663866 - CHIP ID = 0x100 MSM Version = 0x10000
  36. B - 1668594 - Board Type = 0x8 Version = 0x10000
  37. B - 1673047 - DDR Frequency = 450000 kHz
  38. B - 1678354 - Start DDR RCW Training
  39. B - 1680458 - DDR RCW Training Results Start=0x07070707 Coarse=0x00002222 Fine=0x30302c30
  40. B - 1688083 - DDR CH0 Start Address:0x00000000_00000000 Size:0x400 MBytes
  41. D - 30683 - sbl1_ddr_init, Delta
  42. B - 1724012 - sbl1_tlmm_init, Start
  43. D - 91 - sbl1_tlmm_init, Delta
  44. B - 1724348 - Image Load, Start
  45. B - 1739750 - Tz Execution, Start
  46. D - 218258 - Tz Execution, Delta
  47. B - 1981737 - Image Load, Start
  48. B - 1981890 - Image Load, Start
  49. B - 1981951 - Image Load, Start
  50. B - 2000373 - sbl1_efs_handle_cookies, Start
  51. D - 549 - sbl1_efs_handle_cookies, Delta
  52. B - 2002264 - SBL1, End
  53. Android Bootloader - UART_DM Initialized!!!
  54. [0] welcome to lk
  55. [0] Casa Systems Inc.
  56. [10] platform_init()
  57. [20] target_init()
  58. [30] SDHC Running at 200 MHz
  59. [70] SDHC Running in HS200 mode
  60. [90] Done initialization of the card
  61. [120] scm call to check secure boot fuses failed
  62. [140] Neither 'config' nor 'frp' partition found
  63. [170] Press 1 to enable fast boot mode...
  64. [270] Trying to use 'boot_1' image...
  65. [290] Loading (boot) image (32886784): start
  66. [540] Loading (boot) image (32886784): done
  67. [560] use_signed_kernel=0, is_unlocked=0, is_tampered=0.
  68. [590] Uncpmpressed kernel in use
  69. [610] Kernel image not patched..Unable to locate dt offset
  70. [910] DTB Total entry: 20, DTB version: 3
  71. [940] Using DTB entry 0x00000100/00000000/0x00010008/0 for device 0x00000100/00010000/0x00010008/0
  72. [990] cmdline: root=/dev/ram0 rw rdinit=/sbin/init console=ttyHSL0,115200n8 earlyprintk maxcpus=4 coherent_pool=3M mem=196M@0x03c00000 mem=360M@0x29800000 vmalloc=512M androidboot.emmc=true androidboot.serialno=a6d30590 androidboot.baseband=msm cs_version=1 bun[1130] Updating device tree: start
  73. [1160] Updating device tree: done
  74. [1180] booting linux @ 0x3c08000, ramdisk @ 0x4d00000 (28125856), tags/device tree @ 0x4c00000
  75. [ 0.000000] Booting Linux on physical CPU 0x0
  76. [ 0.000000] Initializing cgroup subsys cpuset
  77. [ 0.000000] Initializing cgroup subsys cpu
  78. [ 0.000000] Initializing cgroup subsys cpuacct
  79. [ 0.000000] Linux version 3.10.84-perf (user@qaserver2) (gcc version 5.4.1 20161213 (Linaro GCC 5.4-2017.01) ) #1 SMP PREEMPT Thu Jan 9 13:39:23 CET 2020
  80. [ 0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=50c5387d
  81. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  82. [ 0.000000] Machine: Qualcomm Technologies, Inc. FSM 9010 (Flattened Device Tree), model: Qualcomm Technologies, Inc. FSM9010 MTP
  83. [ 0.000000] Ignoring memory range 0x0 - 0x3c00000
  84. [ 0.000000] Ignoring memory range 0x0 - 0x3c00000
  85. [ 0.000000] cma: Found qsecom_region, memory base 0x00000000, size 0 MiB, limit 0x15000000
  86. [ 0.000000] cma: CMA: reserved 16 MiB at 0x0f000000 for default region
  87. [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
  88. [ 0.000000] PERCPU: Embedded 12 pages/cpu @c336b000 s28608 r8192 d12352 u49152
  89. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 141944
  90. [ 0.000000] Kernel command line: root=/dev/ram0 rw rdinit=/sbin/init console=ttyHSL0,115200n8 earlyprintk maxcpus=4 coherent_pool=3M mem=196M@0x03c00000 mem=360M@0x29800000 vmalloc=512M androidboot.emmc=true androidboot.serialno=a6d30590 androidboot.baseband=msm cs_version=1 bundle=1
  91. [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
  92. [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
  93. [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
  94. [ 0.000000] Memory: 511608K/569344K available (4887K kernel code, 433K rwdata, 2456K rodata, 215K init, 878K bss, 57736K reserved, 368640K highmem)
  95. [ 0.000000] Virtual kernel memory layout:
  96. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  97. [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  98. [ 0.000000] vmalloc : 0xcc800000 - 0xff000000 ( 808 MB)
  99. [ 0.000000] lowmem : 0xc0000000 - 0xcc400000 ( 196 MB)
  100. [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  101. [ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB)
  102. [ 0.000000] .text : 0xc0008000 - 0xc0733ff4 (7344 kB)
  103. [ 0.000000] .init : 0xc0734000 - 0xc0769fc0 ( 216 kB)
  104. [ 0.000000] .data : 0xc076a000 - 0xc07d6758 ( 434 kB)
  105. [ 0.000000] .bss : 0xc07d681c - 0xc08b20c8 ( 879 kB)
  106. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  107. [ 0.000000] Preemptible hierarchical RCU implementation.
  108. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
  109. [ 0.000000] NR_IRQS:16 nr_irqs:16 16
  110. [ 0.000000] processor id specified, in device tree 5
  111. [ 0.000000] Architected cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
  112. [ 0.000000] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
  113. [ 0.000000] Switching to timer-based delay loop
  114. [ 0.000000] sched_clock: 32 bits at 19MHz, resolution 52ns, wraps every 223696213963ns
  115. [ 0.000000] Console: colour dummy device 80x30
  116. [ 0.000249] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
  117. [ 0.000264] pid_max: default: 32768 minimum: 301
  118. [ 0.000470] Mount-cache hash table entries: 512
  119. [ 0.001354] Initializing cgroup subsys debug
  120. [ 0.001367] Initializing cgroup subsys freezer
  121. [ 0.001406] CPU: Testing write buffer coherency: ok
  122. [ 0.001724] /cpus/cpu@0 missing clock-frequency property
  123. [ 0.001743] /cpus/cpu@1 missing clock-frequency property
  124. [ 0.001761] /cpus/cpu@2 missing clock-frequency property
  125. [ 0.001778] /cpus/cpu@3 missing clock-frequency property
  126. [ 0.001794] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
  127. [ 0.001864] Setting up static identity map for 0xc049c5f8 - 0xc049c644
  128. [ 0.006740] MSM Memory Dump table set up
  129. [ 0.007746] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
  130. [ 0.008641] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
  131. [ 0.009518] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
  132. [ 0.009658] Brought up 4 CPUs
  133. [ 0.009682] SMP: Total of 4 processors activated (153.60 BogoMIPS).
  134. [ 0.009690] CPU: All CPU(s) started in SVC mode.
  135. [ 0.010659] devtmpfs: initialized
  136. [ 0.024550] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 3
  137. [ 0.025527] pinctrl core: initialized pinctrl subsystem
  138. [ 0.025851] regulator-dummy: no parameters
  139. [ 0.026721] NET: Registered protocol family 16
  140. [ 0.030546] DMA: preallocated 3072 KiB pool for atomic coherent allocations
  141. [ 0.031614] stub-regulator-1v: 1000 mV normal idle
  142. [ 0.031934] stub-regulator-1.8v: 1800 mV normal idle
  143. [ 0.032269] stub-regulator-0.95v: 950 mV normal idle
  144. [ 0.032594] stub-regulator_vdd_mx: 0 <--> 0 mV at 0 mV normal idle
  145. [ 0.032930] stub-regulator_3.3v: 3200 mV normal idle
  146. [ 0.040756] gdsc_pcie_0: normal idle
  147. [ 0.041126] gdsc_pcie_1: normal idle
  148. [ 0.042632] socinfo_print: v0.9, id=256, ver=1.0, raw_id=2378, raw_ver=0, hw_plat=8, hw_plat_ver=65536
  149. [ 0.042632] accessory_chip=0, hw_plat_subtype=0, pmic_model=2147483647, pmic_die_revision=0 foundry_id=1
  150. [ 0.042663] invalid MAC address in efuse
  151. [ 0.042686] invalid MAC address in efuse
  152. [ 0.042747] add_danipc_property: adding danipc DT prop dl-bufs=<0x24000000 0x5800000>
  153. [ 0.042761] add_danipc_property: adding danipc DT prop ul-bufs=<0x23800000 0x800000>
  154. [ 0.043713] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
  155. [ 0.043726] hw-breakpoint: maximum watchpoint size is 8 bytes.
  156. [ 0.043888] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
  157. [ 0.043912] platform fc4281d0.qcom,mpm: Driver mpm-v2 requests probe deferral
  158. [ 0.044394] clock-dummy qcom,rpmcc.7: Registered DUMMY provider.
  159. [ 0.048107] qcom,gcc-fsm9010 fc400000.qcom,gcc: Registered GCC clocks
  160. [ 0.050797] sps:sps is ready.
  161. [ 0.070930] bio: create slab <bio-0> at 0
  162. [ 0.071986] dummy_vreg: no parameters
  163. [ 0.072322] vgaarb: loaded
  164. [ 0.072746] usbcore: registered new interface driver usbfs
  165. [ 0.072816] usbcore: registered new interface driver hub
  166. [ 0.072951] usbcore: registered new device driver usb
  167. [ 0.074144] ION heap system created
  168. [ 0.074263] ION heap qsecom created at 0x0f000000 with size 800000
  169. [ 0.075171] pcie:pcie_init.
  170. [ 0.077064] Switching to clocksource arch_sys_counter
  171. [ 0.105922] NET: Registered protocol family 2
  172. [ 0.106784] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
  173. [ 0.106841] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
  174. [ 0.106886] TCP: Hash tables configured (established 2048 bind 2048)
  175. [ 0.106960] TCP: reno registered
  176. [ 0.106978] UDP hash table entries: 256 (order: 1, 8192 bytes)
  177. [ 0.107013] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  178. [ 0.107322] NET: Registered protocol family 1
  179. [ 0.107726] RPC: Registered named UNIX socket transport module.
  180. [ 0.107736] RPC: Registered udp transport module.
  181. [ 0.107745] RPC: Registered tcp transport module.
  182. [ 0.107754] RPC: Registered tcp NFSv4.1 backchannel transport module.
  183. [ 0.108049] Trying to unpack rootfs image as initramfs...
  184. [ 3.028402] Freeing initrd memory: 27464K (c1100000 - c2bd2000)
  185. [ 3.031255] ftr_probe: BoardId = 0x33
  186. [ 3.678219] error setting kswapd cpu affinity mask
  187. [ 3.678441] bounce pool size: 64 pages
  188. [ 3.689131] fuse init (API version 7.23)
  189. [ 3.689649] msgmni has been set to 364
  190. [ 3.691858] NET: Registered protocol family 38
  191. [ 3.692118] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
  192. [ 3.692131] io scheduler noop registered
  193. [ 3.692142] io scheduler deadline registered
  194. [ 3.692165] io scheduler row registered
  195. [ 3.692371] io scheduler cfq registered (default)
  196. [ 3.692382] io scheduler test-iosched registered
  197. [ 3.696252] msm_serial: driver initialized
  198. [ 3.696410] msm_serial_hsl_probe: detected port #0 (ttyHSL0)
  199. [ 3.696437] msm_serial_hsl_probe: Bus scaling is disabled
  200. [ 3.696588] f9920000.serial: ttyHSL0 at MMIO 0xf9920000 (irq = 128) is a MSM
  201. [ 3.696650] msm_hsl_console_setup: console setup on port #0
  202. [ 4.427690] console [ttyHSL0] enabled
  203. [ 4.431694] msm_serial_hsl_probe: detected port #1 (ttyHSL1)
  204. [ 4.436968] msm_serial_hsl_probe: Bus scaling is disabled
  205. [ 4.442476] f991d000.serial: ttyHSL1 at MMIO 0xf991d000 (irq = 127) is a MSM
  206. [ 4.449667] msm_serial_hsl_init: driver initialized
  207. [ 4.465029] diag: In socket_open_server, socket not initialized for MODEM_DATA
  208. [ 4.467021] diag: In socket_open_server, socket not initialized for WCNSS_CNTL
  209. [ 4.468508] diag: In socket_open_server, socket not initialized for MODEM_CNTL
  210. [ 4.470729] diag: In socket_open_server, socket not initialized for LPASS_CNTL
  211. [ 4.471256] diag: In socket_open_server, socket not initialized for LPASS_DATA
  212. [ 4.472515] diag: In socket_open_server, socket not initialized for SENSORS_DATA
  213. [ 4.472620] diag: In socket_open_server, socket not initialized for MODEM_DCI
  214. [ 4.473194] diag: In socket_open_server, socket not initialized for SENSORS_CNTL
  215. [ 4.473486] diag: In socket_open_server, socket not initialized for SENSORS_DCI
  216. [ 4.477226] diag: In __diag_cntl_socket_init, cntl socket is not initialized, ret: -97
  217. [ 4.477240] diag: In socket_open_server, socket not initialized for WCNSS_DCI
  218. [ 4.477450] diag: In socket_open_server, socket not initialized for WCNSS_DATA
  219. [ 4.481155] diag: In socket_open_server, socket not initialized for LPASS_DCI
  220. [ 4.487596] brd: module loaded
  221. [ 4.491484] loop: module loaded
  222. [ 4.491792] QSEECOM: qseecom_probe: qseecom.qsee_version = 0x405000
  223. [ 4.491834] QSEECOM: qseecom_probe: qseecom.appsbl_qseecom_support = 0x0
  224. [ 4.491840] QSEECOM: qseecom_probe: no-clock-support=0x1
  225. [ 4.491841] QSEECOM: qseecom_probe: qsee reentrancy support phase is not defined, setting to default 0
  226. [ 4.491877] QSEECOM: qseecom_probe: secure app region addr=0x13500000 size=0x100000
  227. [ 4.491878] scm_call failed with error code -2
  228. [ 4.491885] QSEECOM: qseecom_check_whitelist_feature: Check whitelist with ret = -22, result = 0x1000
  229. [ 4.491889] QSEECOM: qseecom_probe: qseecom.whitelist_support = 0
  230. [ 4.492232] qfp_fuse_probe: Fuse driver base:cc878000 end:cc87f000
  231. [ 4.492511] QCE50: __qce_get_device_tree_data: BAM Apps EE is not defined, setting to default 1
  232. [ 4.492516] QCE50: __qce_get_device_tree_data: CE operating frequency is not defined, setting to default 100MHZ
  233. [ 4.645467] qcrypto fe0c0000.qcom,qcrypto: Qualcomm Crypto 5.3.0 device found @0xfe0c0000
  234. [ 4.652681] qcrypto fe0c0000.qcom,qcrypto: CE device = 0x0
  235. [ 4.652681] , IO base, CE = 0xcc880000
  236. [ 4.652681] , Consumer (IN) PIPE 0, Producer (OUT) PIPE 1
  237. [ 4.652681] IO base BAM = 0x (null)
  238. [ 4.652681] BAM IRQ 141
  239. [ 4.652681] Engines Availability = 0x1e0111df
  240. [ 4.678177] sps:BAM 0xfe0c4000 is registered.
  241. [ 4.682686] sps:BAM 0xfe0c4000 (va:0xcc8b0000) enabled: ver:0x24, number of pipes:16
  242. [ 4.690591] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x00000000fe0c4000 irq 141
  243. [ 4.701075] bus_scale_table is NULL
  244. [ 4.703658] qcrypto fe0c0000.qcom,qcrypto: qcrypto-ecb-aes
  245. [ 4.709159] qcrypto fe0c0000.qcom,qcrypto: qcrypto-cbc-aes
  246. [ 4.714601] qcrypto fe0c0000.qcom,qcrypto: qcrypto-ctr-aes
  247. [ 4.720070] qcrypto fe0c0000.qcom,qcrypto: qcrypto-ecb-des
  248. [ 4.725511] qcrypto fe0c0000.qcom,qcrypto: qcrypto-cbc-des
  249. [ 4.731005] qcrypto fe0c0000.qcom,qcrypto: qcrypto-ecb-3des
  250. [ 4.736532] qcrypto fe0c0000.qcom,qcrypto: qcrypto-cbc-3des
  251. [ 4.742117] qcrypto fe0c0000.qcom,qcrypto: qcrypto-xts-aes
  252. [ 4.747589] qcrypto fe0c0000.qcom,qcrypto: qcrypto-sha1
  253. [ 4.752768] qcrypto fe0c0000.qcom,qcrypto: qcrypto-sha256
  254. [ 4.758179] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha1-cbc-aes
  255. [ 4.764918] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha1-cbc-des
  256. [ 4.771721] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha1-cbc-3des
  257. [ 4.778578] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha1-cbc-aes
  258. [ 4.785320] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha1-cbc-des
  259. [ 4.792123] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha1-cbc-3des
  260. [ 4.798975] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha256-cbc-aes
  261. [ 4.805893] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha256-cbc-des
  262. [ 4.812862] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha256-cbc-3des
  263. [ 4.819894] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha256-cbc-aes
  264. [ 4.826812] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha256-cbc-des
  265. [ 4.833784] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha256-cbc-3des
  266. [ 4.840815] qcrypto fe0c0000.qcom,qcrypto: qcrypto-hmac-sha1
  267. [ 4.846431] qcrypto fe0c0000.qcom,qcrypto: qcrypto-hmac-sha256
  268. [ 4.852273] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aes-ccm
  269. [ 4.857741] qcrypto fe0c0000.qcom,qcrypto: qcrypto-rfc4309-aes-ccm
  270. [ 4.863767] qcrypto: FIPS140-2 Known Answer Tests: Skipped
  271. [ 4.869363] QCE50: __qce_get_device_tree_data: BAM Apps EE is not defined, setting to default 1
  272. [ 4.877946] QCE50: __qce_get_device_tree_data: CE operating frequency is not defined, setting to default 100MHZ
  273. [ 4.889576] qcrypto fe0c0000.qcom,qcrypto1: Qualcomm Crypto 5.3.0 device found @0xfe0c0000
  274. [ 4.896810] qcrypto fe0c0000.qcom,qcrypto1: CE device = 0x10
  275. [ 4.896810] , IO base, CE = 0xcc8c0000
  276. [ 4.896810] , Consumer (IN) PIPE 6, Producer (OUT) PIPE 7
  277. [ 4.896810] IO base BAM = 0x (null)
  278. [ 4.896810] BAM IRQ 141
  279. [ 4.896810] Engines Availability = 0x1e0111df
  280. [ 4.923006] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x00000000fe0c4000 irq 141
  281. [ 4.933130] bus_scale_table is NULL
  282. [ 4.935576] qcrypto: FIPS140-2 Known Answer Tests: Skipped
  283. [ 4.941171] QCE50: __qce_get_device_tree_data: BAM Apps EE is not defined, setting to default 1
  284. [ 4.949756] QCE50: __qce_get_device_tree_data: CE operating frequency is not defined, setting to default 100MHZ
  285. [ 4.960738] qcrypto fe0c0000.qcom,qcrypto2: Qualcomm Crypto 5.3.0 device found @0xfe0c0000
  286. [ 4.968084] qcrypto fe0c0000.qcom,qcrypto2: CE device = 0x20
  287. [ 4.968084] , IO base, CE = 0xcc900000
  288. [ 4.968084] , Consumer (IN) PIPE 8, Producer (OUT) PIPE 9
  289. [ 4.968084] IO base BAM = 0x (null)
  290. [ 4.968084] BAM IRQ 141
  291. [ 4.968084] Engines Availability = 0x1e0111df
  292. [ 4.994254] QCE50: qce_sps_init: Qualcomm MSM CE-BAM at 0x00000000fe0c4000 irq 141
  293. [ 5.004388] bus_scale_table is NULL
  294. [ 5.006835] qcrypto: FIPS140-2 Known Answer Tests: Skipped
  295. [ 5.013930] tun: Universal TUN/TAP device driver, 1.6
  296. [ 5.018005] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
  297. [ 5.024342] PPP generic driver version 2.4.2
  298. [ 5.029578] FIFO apps_ipc_data FOUND!
  299. [ 5.032234] FIFO apps_ipc_pcap FOUND!
  300. [ 5.035845] FIFO apps_hex_ipc_log NOT FOUND!
  301. [ 5.040165] FIFO apps_hex_ipc_log NOT FOUND!
  302. [ 5.047075] msm_sharedmem: sharedmem_register_qmi: Creating sharedmem_qmi qmi handle failed
  303. [ 5.047377] msm_sharedmem: msm_sharedmem_probe: Device created for client 'rmtfs'
  304. [ 5.062846] msm-dwc3 f9200000.ssusb: bus scaling is disabled
  305. [ 5.069370] i2c /dev entries driver
  306. [ 5.074003] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: [email protected]
  307. [ 5.081457] device-mapper: req-crypt: dm-req-crypt successfully initalized.
  308. [ 5.081457]
  309. [ 5.089977] cpuidle: using governor ladder
  310. [ 5.093901] cpuidle: using governor menu
  311. [ 5.097912] sdhci: Secure Digital Host Controller Interface driver
  312. [ 5.103969] sdhci: Copyright(c) Pierre Ossman
  313. [ 5.108337] sdhci-pltfm: SDHCI platform and OF driver helper
  314. [ 5.114074] sdhci_msm f9824900.sdhci: sdhci_msm_probe: ICE device is not enabled
  315. [ 5.121492] sdhci_msm f9824900.sdhci: Parsing Pinctrl failed with -22, falling back on GPIO lib
  316. [ 5.130270] sdhci_msm f9824900.sdhci: host_use_default_qos = 1
  317. [ 5.135834] sdhci_msm f9824900.sdhci: For qos_policy(default qos) = 0, tbl_sz = 1, qos type = 2
  318. [ 5.144537] sdhci_msm f9824900.sdhci: dma_latency = 200
  319. [ 5.149848] sdhci_msm f9824900.sdhci: For qos_policy(modified dynamic qos) = 1, tbl_sz = 1, qos type = 2
  320. [ 5.159297] sdhci_msm f9824900.sdhci: dma_latency = 200
  321. [ 5.164566] sdhci_msm f9824900.sdhci: For qos_policy(modified dynamic qos) = 2, tbl_sz = 1, qos type = 2
  322. [ 5.174052] sdhci_msm f9824900.sdhci: dma_latency = 200
  323. [ 5.179365] sdhci_msm f9824900.sdhci: Host using default pm_qos
  324. [ 5.185977] mmc0: no vqmmc regulator found
  325. [ 5.189338] mmc0: no vmmc regulator found
  326. [ 5.193491] mmc0: SDHCI controller on f9824900.sdhci [f9824900.sdhci] using 32-bit ADMA in legacy mode
  327. [ 5.230998] ssbi f9b18000.qcom,ssbi: SSBI controller type: 'geni-ssbi-arbiter'
  328. [ 5.237974] ssbi f9b1c000.qcom,ssbi: SSBI controller type: 'geni-ssbi-arbiter'
  329. [ 5.244759] ssbi f9b20000.qcom,ssbi: SSBI controller type: 'geni-ssbi-arbiter'
  330. [ 5.251956] ssbi f9b24000.qcom,ssbi: SSBI controller type: 'geni-ssbi-arbiter'
  331. [ 5.259202] ssbi f9b28000.qcom,ssbi: SSBI controller type: 'geni-ssbi-arbiter'
  332. [ 5.266566] usbcore: registered new interface driver usbhid
  333. [ 5.271580] usbhid: USB HID core driver
  334. [ 5.276095] u32 classifier
  335. [ 5.278251] ipip: IPv4 over IPv4 tunneling driver
  336. [ 5.278873] mmc0: BKOPS_EN bit = 0
  337. [ 5.278879] mmc0: eMMC FW version: 0x01
  338. [ 5.285135] mmc0: new HS200 MMC card at address 0001
  339. [ 5.295003] mmcblk0: mmc0:0001 004GA0 3.68 GiB
  340. [ 5.295552] TCP: cubic registered
  341. [ 5.295555] Initializing XFRM netlink socket
  342. [ 5.296285] NET: Registered protocol family 10
  343. [ 5.297421] NET: Registered protocol family 17
  344. [ 5.297447] NET: Registered protocol family 15
  345. [ 5.297521] Bridge firewalling registered
  346. [ 5.297588] 8021q: 802.1Q VLAN Support v1.8
  347. [ 5.299795] sctp: Hash tables configured (established 65536 bind 65536)
  348. [ 5.300448] NET: Registered protocol family 27
  349. [ 5.339759] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB
  350. [ 5.339996] Registering SWP/SWPB emulation handler
  351. [ 5.341312] regulator-dummy: disabling
  352. [ 5.342640] qcom,cc-debug-fsm9010 fc400000.qcom,cc-debug: Registered Debug Mux successfully
  353. [ 5.342964] android_probe: pm_qos latency not specified 0
  354. [ 5.343305] file system registered
  355. [ 5.343378] mbim_init: initialize 1 instances
  356. [ 5.343521] mbim_init: Initialized 1 ports
  357. [ 5.343524] mbim_bam_setup: no_ports:1
  358. [ 5.343645] mbim_bam_setup: Initialized 1 ports
  359. [ 5.345165] rndis_qc_init: initialize rndis QC instance
  360. [ 5.345732] android_usb gadget: Mass Storage Function, version: 2009/09/11
  361. [ 5.345737] android_usb gadget: Number of LUNs=1
  362. [ 5.345743] lun0: LUN: removable file: (no medium)
  363. [ 5.346201] android_usb gadget: android_usb ready
  364. [ 5.346357] /home/user/jenkins/workspace/QualcommBspArtifact/build_90xx/LINUX/opensource/kernel/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
  365. [ 5.346401] msm_thermal:interrupt_mode_init Interrupt mode init
  366. [ 5.346875] clock_late_init: Removing enables held for handed-ofþ[ 5.440402] Freeing unused kernel memory: 212K (c0734000 - c0769000)
  367. [ 5.447751]Å p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32
  368. ​
  369. starting pid 217, tty '': '/etc/init.d/rcS'
  370. rcS:::executing /etc/init.d/rcS script
  371. rcS:::mounting filesystems
  372. rcS:::generating ld.so.cache
  373. rcS:::executing /etc/rc.d scripts
  374. starting udev
  375. creating static nodes
  376. starting udevd...[ 5.556616] udevd[234]: starting version 182
  377. done
  378. waiting for devices...done
  379. [ 6.050681] mountflash:::Mounting /dev/disk/by-partlabel/modem_1 on /mnt/firmware
  380. [ 6.073832] mountflash:::Mounting /dev/disk/by-partlabel/rfcal on /mnt/rfcal
  381. [ 6.093951] EXT4-fs (mmcblk0p6): recovery complete
  382. [ 6.098466] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)
  383. [ 6.111151] mountflash:::Mounting /dev/disk/by-partlabel/system_1 on /opt
  384. [ 6.124526] EXT4-fs (mmcblk0p30): mounted filesystem with ordered data mode. Opts: (null)
  385. [ 6.137075] mountflash:::Mounting /dev/disk/by-partlabel/userdata on /mnt/flash
  386. [ 6.155393] EXT4-fs (mmcblk0p14): recovery complete
  387. [ 6.159974] EXT4-fs (mmcblk0p14): mounted filesystem with ordered data mode. Opts: (null)
  388. [ 6.181889] mountflash:::Mounting /dev/disk/by-partlabel/stack_1 on /stack
  389. [ 6.198366] EXT4-fs (mmcblk0p31): recovery complete
  390. [ 6.203192] EXT4-fs (mmcblk0p31): mounted filesystem with ordered data mode. Opts: (null)
  391. [ 6.215415] mountflash:::Mounting /dev/disk/by-partlabel/config_1 on /config
  392. [ 6.237409] EXT4-fs (mmcblk0p32): recovery complete
  393. [ 6.241945] EXT4-fs (mmcblk0p32): mounted filesystem with ordered data mode. Opts: (null)
  394. [ 6.261852] mountflash:::generating ld.so.cache
  395. /etc/rc.d/S02persist-fixup: fixing up persistent files
  396. /etc/rc.d/S02persist-fixup: fixed up entry /root
  397. /etc/rc.d/S02persist-fixup: fixed up entry /home
  398. /etc/rc.d/S02persist-fixup: fixed up entry /etc/dropbear/dropbear_dss_host_key
  399. /etc/rc.d/S02persist-fixup: fixed up entry /etc/dropbear/dropbear_rsa_host_key
  400. /etc/rc.d/S02persist-fixup: fixed up entry /etc/rsyslog.conf
  401. /etc/rc.d/S02persist-fixup: done fixing up persistent files
  402. running rc.once.d services...
  403. Creating dynamic linker cache...
  404. syslogd starting
  405. klogd starting
  406. boardinit:::Loading NSS GMAC ethernet module
  407. [ 6.625878] libphy: GPIO Bitbanged MDIO: probed
  408. [ 6.650109] **********************************************************
  409. [ 6.655610] * Driver :NSS GMAC Driver for RTL v(3.72a)
  410. [ 6.661052] * Version :1.0
  411. [ 6.663875] * Copyright :Copyright (c) 2013-2016 The Linux Foundation. All rights reserved.
  412. [ 6.672232] **********************************************************
  413. [ 6.679371] GMAC0(ca7ae500) Invalid MAC@ - using 46:47:48:49:4a:4b
  414. [ 6.689596] GMAC1(ca7af500) Invalid MAC@ - using e6:e7:e8:e9:ea:eb
  415. boardinit:::Setting up coredump location in /mnt/flash
  416. boardinit:::Creating /dev/mqueue
  417. fs.mqueue.msg_max = 256
  418. starting dropbear...done
  419. Setting up LVM2...
  420. No volume groups found
  421. done
  422. Using stack init scripts to configure networking.
  423. stop syslogd stopping syslog
  424. /etc/rc.d/S84rsyslogd: line 70: 399 Terminated /etc/init.d/syslogd stop
  425. ​
  426. Starting system logger (rsyslogd):
  427. Starting OAM Proxy (/opt/qcom/bin/fsmOamProxy):
  428. Starting (/opt/qcom/bin/fsmPhyTraceProxy):
  429. loading modules
  430. /etc/rc.d/S99persist-save: saving persistent files
  431. /etc/rc.d/S99persist-save: done saving persistent files
  432. rcS:::configuring ACPU parameters
  433. rcS::Starting fsminitd
  434. Starting (/local/qcom/bin/fsminit/fsminitd):
  435. rcS::fsminitd started
  436. rcS:::Running /stack/etc/rc.once.d scripts
  437. [ 7.294237] /etc/init.d/sentinel ::: Started ...
  438. [ 7.299244] /etc/init.d/sentinel ::: Checking partitions ...
  439. [ 7.341433] /etc/init.d/sentinel ::: Waiting 1200 seconds to stack boot up ...
  440. rcS:::Running /stack/etc/rc.d scripts
  441. [ 7.448887] warning: `fsmPhyTraceProx' uses 32-bit capabilities (legacy support in use)
  442. Waiting for fsminitd (reattemp 1)...
  443. Waiting for fsminitd (reattemp 2)...
  444. [ 11.503371] pil-femto-modem fbc00000.qcom,modem-femto: mba: loading from 0x13080000 to 0x130da000
  445. [ 11.578483] pil-femto-modem fbc00000.qcom,modem-femto: MBA boot done
  446. [ 11.583817] pil-femto-modem fbc00000.qcom,modem-femto: mba: Brought out of reset
  447. [ 11.591449] pil-femto-modem-desc fd4a7000.qcom,modem: mdm0_00: loading from 0x16400000 to 0x17848000
  448. [ 11.783828] pil-femto-modem-desc fd4a7000.qcom,modem: mdm0_00: Brought out of reset
  449. [ 11.790939] pil-femto-modem-desc fd4a7030.qcom,modem: mdm1_00: loading from 0x18000000 to 0xfb840000
  450. [ 12.352464] pil-femto-modem-desc fd4a7030.qcom,modem: mdm1_00: Brought out of reset
  451. [ 12.359302] pil-femto-modem-desc fd4a7060.qcom,modem: mdm2_00: loading from 0x00800000 to 0xf7998000
  452. [ 12.520793] pil-femto-modem-desc fd4a7060.qcom,modem: mdm2_00: Brought out of reset
  453. [ 12.527597] pil-femto-modem-desc fd4a7090.qcom,modem: mdm3_00: loading from 0x14000000 to 0x140a1000
  454. [ 12.554830] pil-femto-modem-desc fd4a7090.qcom,modem: mdm3_00: Brought out of reset
  455. [ 12.592188] smsm_change_state <SM NO STATE>
  456. [ 12.596207] diag: In diag_send_feature_mask_update, control channel is not open, p: 0, c086b878
  457. [ 12.682960] smsm_change_state <SM NO STATE>
  458. Waiting for fsminitd (reattemp 3)...
  459. [ 12.848968] Synchronized with fsminitd
  460. [ 13.110042] incorrect memory info c1005d8c len 16
  461. [ 13.128582] <NSS-CRYPTO>:module loaded (platform - IPQ806x, build - Build_ID - 01/09/20, 13:39:57)
  462. [ 13.137611] <NSS-CRYPTO>:Register with NSS driver-
  463. [ 13.154326] crypto bench loaded - Build_ID - 01/09/20, 13:39:57
  464. Shutting down system logger (rsyslogd): [ 13.181023] nss_ipsecmgr_init[1362]:NSS IPsec manager loaded: Build Id: 01/09/20, 13:39:57
  465. stopped /usr/sbin/rsyslogd (pid 405)
  466. ​
  467. [ 13.200850] nss_nl_init[296]:NSS Netlink manager loaded: Build Id: 01/09/20, 13:39:57
  468. [ 13.207739] nss_nl_init[314]:attaching family:nss_nlcrypto
  469. [ 13.213119] nss_nlcrypto_init[598]:initiallizing the NSS netlink crypto handler
  470. [ 13.220563] nss_nl_init[314]:attaching family:nss_nlipv4
  471. [ 13.225717] nss_nlipv4_init[793]:Init NSS netlink IPv4 handler
  472. [ 13.231579] nss_nl_init[314]:attaching family:nss_nlipsec
  473. [ 13.236903] nss_nlipsec_init[1150]:Init NSS netlink IPsec handler
  474. [ 13.243023] <NSS-CRYPTO>:NSS Firmware initialized
  475. [ 13.247746] nss_nl_init[314]:attaching family:nss_nloam
  476. [ 13.247912] <NSS-CRYPTO>:probing engine - 0
  477. [ 13.247915] <NSS-CRYPTO>:Device Tree node found
  478. [ 13.248040] <NSS-CRYPTO>:init completed for Pipe Pair[0]
  479. [ 13.248056] <NSS-CRYPTO>:init completed for Pipe Pair[1]
  480. [ 13.272241] nss_nl_init[314]:attaching family:nss_nlipv6
  481. [ 13.277761] nss_nlipv6_init[777]:Init NSS netlink IPV6 handler
  482. [ 14.151143] <NSS-CRYPTO>:probing engine - 1
  483. [ 14.154290] <NSS-CRYPTO>:Device Tree node found
  484. [ 14.158912] <NSS-CRYPTO>:init completed for Pipe Pair[0]
  485. [ 14.164114] <NSS-CRYPTO>:init completed for Pipe Pair[1]
  486. Starting system logger (rsyslogd):
  487. /stack/etc/rc.d/S01stackenv: line 181: /sys/kernel/debug/tracing/tracing_on: No such file or directory
  488. [ 14.489641] Configuring board type: 9016, RF id: 51
  489. [ 14.521093] hex2_shm: registered correctly with major number 243
  490. [ 14.526119] hex2_shm: device class registered correctly
  491. [ 14.531663] hex2_shm: device class created correctly
  492. [ 14.544826] casa_gpio: Initializing
  493. [ 14.547346] casa_gpio: Valid GPIO in device tree (red_led-gpio,1002)
  494. [ 14.553636] casa_gpio: Valid GPIO in device tree (green_led-gpio,954)
  495. [ 14.560103] casa_gpio: Valid GPIO in device tree (blue_led-gpio,956)
  496. [ 14.566400] casa_gpio: GPIO not found in device tree (orange_led-gpio)
  497. [ 14.572962] casa_gpio: Valid GPIO in device tree (reset_button-gpio,955)
  498. [ 14.579842] casa_gpio: GPIO not found in device tree (killswitch_button-gpio)
  499. [ 14.586704] casa_gpio: Valid GPIO in device tree (wifireset_control-gpio,958)
  500. [ 14.593998] casa_gpio: Valid GPIO in device tree (wifiwps_control-gpio,959)
  501. [ 14.901258] health_monitor started
  502. [ 15.221004] smsm_change_state <SM NO STATE>
  503. [ 15.244172] oam_proxy started
  504. [ 16.829311] system_layer: System layer start
  505. [ 16.959352] system_layer: [OAM] Component registration complete
  506. [ 16.975809] system_layer: [OAM] Subscribed to event: no_ues_connected
  507. [ 16.991461] system_layer: [OAM] Subscribed to event: ues_connected
  508. [ 17.006579] system_layer: [OAM] Subscribed to event: location_acquired
  509. [ 17.021655] system_layer: [OAM] Subscribed to event: waiting_for_wifi_configuration
  510. [ 17.037588] system_layer: [OAM] Subscribed to event: booting
  511. [ 17.051808] system_layer: [OAM] Subscribed to event: admin_mode_enabled
  512. [ 17.066571] system_layer: [OAM] Subscribed to event: enb_online
  513. [ 17.080758] system_layer: [OAM] Subscribed to event: acquiring_backhaul
  514. [ 17.095761] system_layer: [OAM] Subscribed to event: acquiring_location
  515. [ 17.110645] system_layer: [OAM] Subscribed to event: critical_alarm_raised
  516. [ 17.125965] system_layer: [OAM] Subscribed to event: factory_reset
  517. [ 17.140724] system_layer: [OAM] Subscribed to event: disabling_admin_mode
  518. [ 17.156373] system_layer: [OAM] Subscribed to event: backhaul_acquired
  519. [ 17.253088] system_layer: Starting WiFi module
  520. [ 38.150284] qup_i2c f9924000.i2c: QUP: I2C status flags :0x1363c8, irq:129
  521. [ 38.156225] qup_i2c f9924000.i2c: I2C slave addr:0x54 not connected
  522. [ 39.361017] qup_i2c f9924000.i2c: QUP: I2C status flags :0x1363c8, irq:129
  523. [ 39.366881] qup_i2c f9924000.i2c: I2C slave addr:0x54 not connected
  524. [ 53.048779] system_layer: Wifi module boot up completed.
  525. [ 53.219053] system_layer: WiFi Module Banner:
  526. [ 53.219053] _______ ________ __
  527. [ 53.219053] | |.-----.-----.-----.| | | |.----.| |_
  528. [ 53.219053] | - || _ | -__| || | | || _|| _|
  529. [ 53.219053] |_______|| __|_____|__|__||________||__| |____|
  530. [ 53.219053] |__| W I R E L E S S F R E E D O M
  531. [ 53.219053] -----------------------------------------------------
  532. [ 53.219053] BARRIER BREAKER (Barrier Breaker, r15)
  533. [ 53.219053] -----------------------------------------------------
  534. [ 53.219053] * 1/2 oz Galliano Pour all ingredients into
  535. [ 53.219053] * 4 oz cold Coffee an irish coffee mug filled
  536. [ 53.219053] * 1 1/2 oz Dark Rum with crushed ice. Stir.
  537. [ 53.219053] * 2 tsp. Creme de Cacao
  538. [ 53.219053] -----------------------------------------------------
  539. [ 53.219053] MTK OpenWrt SDK V3.4
  540. [ 53.219053] revision : 1443366e
  541. [ 53.219053] benchmark : APSoC SDK 5.0.1.0
  542. [ 53.343649] system_layer: WiFi Module Uptime :
  543. [ 53.343649] 06:56:43 up 0 min, load average: 1.05, 0.29, 0.09
  544. [ 53.343649]
  545. [ 53.393371] system_layer: WiFi Module Version :
  546. [ 53.393371] MOWIFI CX2 V1.0
  547. [ 53.393371] 1.0.1 Build 20190508 Rel.15n
  548. [ 53.393371] G24=1 G5=1
  549. [ 53.393371]
  550. [ 53.428688] system_layer: Configuring WiFi DHCP...
  551. [ 55.288756] system_layer: WiFi DHCP configured
  552. [ 55.302982] system_layer: [OAM] Subscribed to event: enabling_admin_mode
  553. [ 55.318650] system_layer: [OAM] Subscribed to event: admin_mode_enabled
  554. [ 55.334924] system_layer: [OAM] Subscribed to event: disabling_admin_mode
  555. [ 55.350186] system_layer: [OAM] Subscribed to event: enb_online
  556. [ 55.364950] system_layer: [OAM] Subscribed to event: forced_reboot
  557. [ 55.379766] system_layer: [OAM] Subscribed to event: acquiring_location
  558. [ 55.395212] system_layer: [OAM] Subscribed to event: location_acquired
  559. [ 55.410946] system_layer: [OAM] Subscribed to event: failure_acquiring_location
  560. [ 55.426937] system_layer: [OAM] Subscribed to event: critical_alarm_raised
  561. [ 55.442358] system_layer: [OAM] Subscribed to event: critical_alarm_cleared
  562. [ 55.566698] system_layer: [OAM] Subscribed to event: location_acquired
  563. [ 55.579353] system_layer: Configured device_time zone to UTC
  564. [ 55.597645] system_layer: [OAM] Subscribed to event: backhaul_acquired
  565. [ 56.978421] system_layer: Interface eth0 MAC address set to 00:17:10:27:E0:46
  566. [ 57.018432] system_layer: Interface eth1 MAC address set to 02:17:10:27:E0:46
  567. [ 57.026351] system_layer: Preferred Backhaul Mode: ethernet
  568. [ 57.032142] system_layer: Preferred Backhaul Ethernet
  569. [ 57.037191] system_layer: Configuring Ethernet Backhaul
  570. [ 57.074153] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  571. [ 67.139316] system_layer: Failure configuring Ethernet Backhaul
  572. [ 67.145194] system_layer: Interface eth0 state did not change to up: Condition not meet after 10 seconds with interval 0.1
  573. [ 67.156319] system_layer: Configuring WiFi Backhaul
  574. [ 67.161128] system_layer: Enabling WiFi STA
  575. [ 68.198868] system_layer: Failure configuring WiFi Backhaul
  576. [ 68.204516] system_layer: No STA configured
  577. [ 68.208782] system_layer: Configuring WiFi AP. SSID: Sprint-Pebble
  578. [ 68.214986] system_layer: Configuring WiFi...
  579. [ 97.118700] system_layer: WiFi configured as AP
  580. [ 97.186549] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
  581. [ 100.699352] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
  582. [ 100.711355] eth1: 1000 Mbps Full Duplex
  583. [ 100.716001] system_layer: eth1: Using DHCP...
  584. [ 114.124619] BACKHAUL_INTERFACE = , interface = eth1, ip = 192.168.51.2
  585. [ 114.130610] Setting hostname to pebble
  586. [ 114.131904] system_layer: eth1 IP set by DHCP
  587. [ 114.144139] eth1: deleting routers
  588. [ 114.159869] eth1: Deleting dns from /etc/resolv.conf
  589. [ 114.170296] eth1: adding dns 192.168.51.1
  590. [ 114.239107] system_layer: System layer started
  591. [ 114.243545] system_layer: Creating Sentinel Mark /tmp/watchdog_alive
  592. [ 114.836096] ftrm started
  593. [ 114.877390] locmgr started
  594. [ 114.919657] nl started
  595. [ 114.966402] nlSyncApp started
  596. [ 115.087976] Waiting for NSS driver...
  597. [ 115.098436] syncmgr started using GNSS as primary source
  598. Accepting OAM request from command line...
  599. RecordID: 0x15010005
  600. RequestType: Set
  601. RequestOpType: Update
  602. RequestData:
  603. <?xml version="1.0"?>
  604. <record>
  605. <key name="subsystem" value="LTE_L1"/>
  606. <field name="logToFile" value="false"/>
  607. </record>
  608. Result: Success
  609. Apply Action: no-action-required
  610. ​
  611. Accepting OAM request from command line...
  612. RecordID: 0x15010005
  613. RequestType: Set
  614. RequestOpType: Update
  615. RequestData:
  616. <?xml version="1.0"?>
  617. <record>
  618. <key name="subsystem" value="COMBINED"/>
  619. <field name="logFileCount" value="2"/>
  620. </record>
  621. Result: Success
  622. Apply Action: no-action-required
  623. ​
  624. [ 117.302179] Cleaning residual values on configuration database
  625. [ 117.828649] upnp started
  626. [ 118.739813] Waiting for GPS synchronization...
  627. % Total % Received % Xferd Average Speed Time Time Time Current
  628. Dload Upload Total Spent Left Speed
  629. ​
  630. 0 0 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0
  631. 100 26 0 0 100 26 0 9116 --:--:-- --:--:-- --:--:-- 13000

Edit this Snippet