Snippet content copied to clipboard.
Are you sure to delete this snippet? No, don't delete
  1. U-Boot 2012.07 (Nov 21 2017 - 10:06:29)
  2. ​
  3. smem ram ptable found: ver: 0 len: 5
  4. DRAM: 1 GiB
  5. NAND: Detected MICRON MT29F4G08ABBDAH4, total 512 MiB
  6. SF: Detected MX25U3235F with page size 4 KiB, total 4 MiB
  7. PCI0 Link Intialized
  8. PCI1 Link Intialized
  9. In: serial
  10. Out: serial
  11. Err: serial
  12. ​
  13. PHY ID = 0x4dd074, eth0 found AR8033 PHY
  14. MAC2 addr:7c:5a:1c:34:61:82
  15. PHY ID = 0x4dd074, eth1 found AR8033 PHY
  16. MAC3 addr:7c:5a:1c:34:61:83
  17. eth0, eth1
  18. Creating 1 MTD partitions on "nand0":
  19. 0x000000000000-0x000020000000 : "mtd=0"
  20. UBI: attaching mtd2 to ubi0
  21. UBI: physical eraseblock size: 131072 bytes (128 KiB)
  22. UBI: logical eraseblock size: 126976 bytes
  23. UBI: smallest flash I/O unit: 2048
  24. UBI: VID header offset: 2048 (aligned 2048)
  25. UBI: data offset: 4096
  26. UBI: attached mtd2 to ubi0
  27. UBI: MTD device name: "mtd=0"
  28. UBI: MTD device size: 512 MiB
  29. UBI: number of good PEBs: 4096
  30. UBI: number of bad PEBs: 0
  31. UBI: max. allowed volumes: 128
  32. UBI: wear-leveling threshold: 4096
  33. UBI: number of internal volumes: 1
  34. UBI: number of user volumes: 3
  35. UBI: available PEBs: 40
  36. UBI: total number of reserved PEBs: 4056
  37. UBI: number of PEBs reserved for bad PEB handling: 40
  38. UBI: max/mean erase counter: 29/5
  39. SF: Detected MX25U3235F with page size 4 KiB, total 4 MiB
  40. Hit any key to stop autoboot: 0
  41. Read 0 bytes from volume image to 44000000
  42. No size specified -> Using max size (3174400)
  43. ## Booting kernel from FIT Image at 44000000 ...
  44. Using 'config@2' configuration
  45. Trying 'kernel-1' kernel subimage
  46. Description: ARM OpenWrt Linux-5.10.90
  47. Type: Kernel Image
  48. Compression: uncompressed
  49. Data Start: 0x440000e4
  50. Data Size: 3132784 Bytes = 3 MiB
  51. Architecture: ARM
  52. OS: Linux
  53. Load Address: 0x42208000
  54. Entry Point: 0x42208000
  55. node name: hash@1
  56. Hash algo: crc32
  57. Hash value: 4bb2f5fe
  58. node name: hash@2
  59. Hash algo: sha1
  60. Hash value: 02a44539187ac6baeaafa81bc39288c6f7bdac1c
  61. ## Flattened Device Tree from FIT Image at 44000000
  62. Using 'config@2' configuration
  63. Trying 'fdt-1' FDT blob subimage
  64. Description: ARM OpenWrt sophos_apx530 device tree blob
  65. Type: Flat Device Tree
  66. Compression: uncompressed
  67. Data Start: 0x442fcf8c
  68. Data Size: 30647 Bytes = 29.9 KiB
  69. Architecture: ARM
  70. node name: hash@1
  71. Hash algo: crc32
  72. Hash value: 643eb210
  73. node name: hash@2
  74. Hash algo: sha1
  75. Hash value: ed779c0ad98334bdb811afe7d36de10dc92120d9
  76. Booting using the fdt blob at 0x442fcf8c
  77. Loading Kernel Image ... OK
  78. OK
  79. Using Device Tree in place at 442fcf8c, end 44307742
  80. Using machid 0x136c from environment
  81. ​
  82. Starting kernel ...
  83. ​
  84. [ 0.000000] Booting Linux on physical CPU 0x0
  85. [ 0.000000] Linux version 5.10.90 (neg2led@astraea) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r18592-6e02b3c482) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Mon Jan 17 06:44:52 2022
  86. [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
  87. [ 0.000000] CPU: div instructions available: patching division code
  88. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
  89. [ 0.000000] OF: fdt: Machine model: Sophos APX530
  90. [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x42000000
  91. [ 0.000000] earlycon: msm_serial_dm0 at MMIO 0x16340000 (options '')
  92. [ 0.000000] printk: bootconsole [msm_serial_dm0] enabled
  93. [ 0.000000] Memory policy: Data cache writealloc
  94. [ 0.000000] BUG: mapping for 0x16640000 at 0xf0040000 out of vmalloc space
  95. [ 0.000000] Zone ranges:
  96. [ 0.000000] Normal [mem 0x0000000042000000-0x0000000071ffffff]
  97. [ 0.000000] HighMem [mem 0x0000000072000000-0x000000007fffffff]
  98. [ 0.000000] Movable zone start for each node
  99. [ 0.000000] Early memory node ranges
  100. [ 0.000000] node 0: [mem 0x0000000042000000-0x000000007fffffff]
  101. [ 0.000000] Initmem setup node 0 [mem 0x0000000042000000-0x000000007fffffff]
  102. [ 0.000000] On node 0 totalpages: 253952
  103. [ 0.000000] Normal zone: 1728 pages used for memmap
  104. [ 0.000000] Normal zone: 0 pages reserved
  105. [ 0.000000] Normal zone: 196608 pages, LIFO batch:63
  106. [ 0.000000] HighMem zone: 57344 pages, LIFO batch:15
  107. [ 0.000000] percpu: Embedded 15 pages/cpu s30796 r8192 d22452 u61440
  108. [ 0.000000] pcpu-alloc: s30796 r8192 d22452 u61440 alloc=15*4096
  109. [ 0.000000] pcpu-alloc: [0] 0 [0] 1
  110. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 252224
  111. [ 0.000000] Kernel command line: ubi.mtd=rootfs loglevel=8 console=ttyMSM0,115200 ubi.block=0,rootfs root=/dev/ubiblock0_1 rootfstype=squashfs earlycon=msm_serial_dm,0x16340000
  112. [ 0.000000] Bootloader command line not present
  113. [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
  114. [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
  115. [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
  116. [ 0.000000] Memory: 994672K/1015808K available (6930K kernel code, 656K rwdata, 1764K rodata, 1024K init, 242K bss, 21136K reserved, 0K cma-reserved, 229376K highmem)
  117. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  118. [ 0.000000] rcu: Hierarchical RCU implementation.
  119. [ 0.000000] Tracing variant of Tasks RCU enabled.
  120. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
  121. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
  122. [ 0.000000] random: get_random_bytes called from start_kernel+0x3a0/0x54c with crng_init=0
  123. [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
  124. [ 0.000009] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
  125. [ 0.009633] Switching to timer-based delay loop, resolution 160ns
  126. [ 0.017668] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
  127. [ 0.023524] pid_max: default: 32768 minimum: 301
  128. [ 0.034012] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
  129. [ 0.038460] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
  130. [ 0.046641] CPU: Testing write buffer coherency: ok
  131. [ 0.053692] qcom_scm: convention: smc legacy
  132. [ 0.059070] Setting up static identity map for 0x42300000 - 0x42300060
  133. [ 0.062740] rcu: Hierarchical SRCU implementation.
  134. [ 0.069865] smp: Bringing up secondary CPUs ...
  135. [ 0.075591] smp: Brought up 1 node, 2 CPUs
  136. [ 0.078117] SMP: Total of 2 processors activated (25.00 BogoMIPS).
  137. [ 0.082371] CPU: All CPU(s) started in SVC mode.
  138. [ 0.099636] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
  139. [ 0.099833] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  140. [ 0.106589] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
  141. [ 0.116414] pinctrl core: initialized pinctrl subsystem
  142. [ 0.124294] NET: Registered protocol family 16
  143. [ 0.128380] DMA: preallocated 256 KiB pool for atomic coherent allocations
  144. [ 0.133974] thermal_sys: Registered thermal governor 'step_wise'
  145. [ 0.136020] cpuidle: using governor ladder
  146. [ 0.145673] cpuidle: using governor menu
  147. [ 0.193305] usbcore: registered new interface driver usbfs
  148. [ 0.193414] usbcore: registered new interface driver hub
  149. [ 0.197859] usbcore: registered new device driver usb
  150. [ 0.203236] pps_core: LinuxPPS API ver. 1 registered
  151. [ 0.208197] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
  152. [ 0.213172] PTP clock support registered
  153. [ 0.224597] clocksource: Switched to clocksource dg_timer
  154. [ 0.227216] NET: Registered protocol family 2
  155. [ 0.231628] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
  156. [ 0.237063] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
  157. [ 0.243375] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
  158. [ 0.251477] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
  159. [ 0.259492] TCP: Hash tables configured (established 8192 bind 8192)
  160. [ 0.266534] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
  161. [ 0.272804] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
  162. [ 0.279423] NET: Registered protocol family 1
  163. [ 0.286517] PCI: CLS 0 bytes, default 64
  164. [ 0.292159] workingset: timestamp_bits=14 max_order=18 bucket_order=4
  165. [ 0.300426] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  166. [ 0.300991] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  167. [ 0.412332] bounce: pool size: 64 pages
  168. [ 0.414278] gpio-export gpio-export: 4 gpio(s) exported
  169. [ 0.415921] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator
  170. [ 0.420398] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator
  171. [ 0.428019] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator
  172. [ 0.435949] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
  173. [ 0.443292] qcom-pcie 1b500000.pci: Parsing ranges property...
  174. [ 0.450344] qcom-pcie 1b500000.pci: IO 0x000fe00000..0x000fe0ffff -> 0x000fe00000
  175. [ 0.456066] qcom-pcie 1b500000.pci: MEM 0x0008000000..0x000fdfffff -> 0x0008000000
  176. [ 0.692108] qcom-pcie 1b500000.pci: Link up
  177. [ 0.692299] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
  178. [ 0.695218] pci_bus 0000:00: root bus resource [bus 00-ff]
  179. [ 0.701360] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0xfe00000-0xfe0ffff])
  180. [ 0.706912] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
  181. [ 0.716189] pci_bus 0000:00: scanning bus
  182. [ 0.723015] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400
  183. [ 0.727255] pci 0000:00:00.0: supports D1
  184. [ 0.733119] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
  185. [ 0.737124] pci 0000:00:00.0: PME# disabled
  186. [ 0.746509] pci_bus 0000:00: fixups for bus
  187. [ 0.746759] PCI: bus0: Fast back to back transfers disabled
  188. [ 0.750923] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
  189. [ 0.756695] pci_bus 0000:01: scanning bus
  190. [ 0.763742] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000
  191. [ 0.767668] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
  192. [ 0.774763] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
  193. [ 0.780203] pci 0000:01:00.0: PME# disabled
  194. [ 0.790160] pci_bus 0000:01: fixups for bus
  195. [ 0.790266] PCI: bus1: Fast back to back transfers disabled
  196. [ 0.794321] pci_bus 0000:01: bus scan returning with max=01
  197. [ 0.799983] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
  198. [ 0.805516] pci_bus 0000:00: bus scan returning with max=ff
  199. [ 0.812400] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
  200. [ 0.817768] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
  201. [ 0.824755] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
  202. [ 0.831815] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
  203. [ 0.837207] pcieport 0000:00:00.0: assign IRQ: got 46
  204. [ 0.844658] pcieport 0000:00:00.0: AER: enabled with IRQ 47
  205. [ 0.849087] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
  206. [ 0.854312] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100547)
  207. [ 0.862736] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
  208. [ 0.870452] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10010)
  209. [ 0.878771] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0x0)
  210. [ 0.886603] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0)
  211. [ 0.894066] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
  212. [ 0.901785] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0xf0)
  213. [ 0.910126] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0x8100800)
  214. [ 0.917851] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
  215. [ 0.925902] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0)
  216. [ 0.933648] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0)
  217. [ 0.941376] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0)
  218. [ 0.948989] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x40)
  219. [ 0.956643] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0)
  220. [ 0.964550] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x3012e)
  221. [ 0.972694] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator
  222. [ 0.980230] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator
  223. [ 0.987728] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator
  224. [ 0.995620] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
  225. [ 1.003021] qcom-pcie 1b700000.pci: Parsing ranges property...
  226. [ 1.010069] qcom-pcie 1b700000.pci: IO 0x0031e00000..0x0031e0ffff -> 0x0031e00000
  227. [ 1.015771] qcom-pcie 1b700000.pci: MEM 0x002e000000..0x0031dfffff -> 0x002e000000
  228. [ 1.252147] qcom-pcie 1b700000.pci: Link up
  229. [ 1.252323] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
  230. [ 1.255269] pci_bus 0001:00: root bus resource [bus 00-ff]
  231. [ 1.261393] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x31e00000-0x31e0ffff])
  232. [ 1.266951] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
  233. [ 1.276569] pci_bus 0001:00: scanning bus
  234. [ 1.283390] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400
  235. [ 1.287622] pci 0001:00:00.0: supports D1
  236. [ 1.293500] pci 0001:00:00.0: PME# supported from D0 D1 D3hot
  237. [ 1.297512] pci 0001:00:00.0: PME# disabled
  238. [ 1.306807] pci_bus 0001:00: fixups for bus
  239. [ 1.307140] PCI: bus0: Fast back to back transfers disabled
  240. [ 1.311301] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0
  241. [ 1.317054] pci_bus 0001:01: scanning bus
  242. [ 1.324123] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000
  243. [ 1.328081] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
  244. [ 1.335230] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold
  245. [ 1.340503] pci 0001:01:00.0: PME# disabled
  246. [ 1.350552] pci_bus 0001:01: fixups for bus
  247. [ 1.350656] PCI: bus1: Fast back to back transfers disabled
  248. [ 1.354702] pci_bus 0001:01: bus scan returning with max=01
  249. [ 1.360365] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1
  250. [ 1.365900] pci_bus 0001:00: bus scan returning with max=ff
  251. [ 1.372776] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
  252. [ 1.378148] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
  253. [ 1.385202] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
  254. [ 1.392121] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
  255. [ 1.397584] pcieport 0001:00:00.0: assign IRQ: got 48
  256. [ 1.405099] pcieport 0001:00:00.0: AER: enabled with IRQ 49
  257. [ 1.409398] pcieport 0001:00:00.0: saving config space at offset 0x0 (reading 0x10117cb)
  258. [ 1.414692] pcieport 0001:00:00.0: saving config space at offset 0x4 (reading 0x100547)
  259. [ 1.423126] pcieport 0001:00:00.0: saving config space at offset 0x8 (reading 0xff000000)
  260. [ 1.430836] pcieport 0001:00:00.0: saving config space at offset 0xc (reading 0x10010)
  261. [ 1.439185] pcieport 0001:00:00.0: saving config space at offset 0x10 (reading 0x0)
  262. [ 1.446986] pcieport 0001:00:00.0: saving config space at offset 0x14 (reading 0x0)
  263. [ 1.454446] pcieport 0001:00:00.0: saving config space at offset 0x18 (reading 0xff0100)
  264. [ 1.462170] pcieport 0001:00:00.0: saving config space at offset 0x1c (reading 0xf0)
  265. [ 1.470510] pcieport 0001:00:00.0: saving config space at offset 0x20 (reading 0x2e102e00)
  266. [ 1.478236] pcieport 0001:00:00.0: saving config space at offset 0x24 (reading 0x1fff1)
  267. [ 1.486285] pcieport 0001:00:00.0: saving config space at offset 0x28 (reading 0x0)
  268. [ 1.494116] pcieport 0001:00:00.0: saving config space at offset 0x2c (reading 0x0)
  269. [ 1.501853] pcieport 0001:00:00.0: saving config space at offset 0x30 (reading 0x0)
  270. [ 1.509467] pcieport 0001:00:00.0: saving config space at offset 0x34 (reading 0x40)
  271. [ 1.517120] pcieport 0001:00:00.0: saving config space at offset 0x38 (reading 0x0)
  272. [ 1.525087] pcieport 0001:00:00.0: saving config space at offset 0x3c (reading 0x30130)
  273. [ 1.535328] L2 @ QSB rate. Forcing new rate.
  274. [ 1.540584] L2 @ 384000 KHz
  275. [ 1.545168] CPU0 @ 800000 KHz
  276. [ 1.547404] CPU1 @ QSB rate. Forcing new rate.
  277. [ 1.550649] CPU1 @ 384000 KHz
  278. [ 1.559175] gsbi 12480000.gsbi: GSBI port protocol: 4 crci: 0
  279. [ 1.561775] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
  280. [ 1.565846] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
  281. [ 1.571483] gsbi 16600000.gsbi: GSBI port protocol: 2 crci: 0
  282. [ 1.577768] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
  283. [ 1.583810] msm_serial 12490000.serial: msm_serial: detected port #1
  284. [ 1.587660] msm_serial 12490000.serial: uartclk = 25000000
  285. [ 1.593915] 12490000.serial: ttyMSM1 at MMIO 0x12490000 (irq = 50, base_baud = 1562500) is a MSM
  286. [ 1.599836] msm_serial 16340000.serial: msm_serial: detected port #0
  287. [ 1.608213] msm_serial 16340000.serial: uartclk = 7372800
  288. [ 1.614477] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 51, base_baud = 46080▒[ 1.628367] printk: console [ttyMSM0] enabled
  289. [ 1.628367] printk: console [ttyMSM0] enabled
  290. [ 1.631705] printk: bootconsole [msm_serial_dm0] disabled
  291. [ 1.631705] printk: bootconsole [msm_serial_dm0] disabled
  292. [ 1.641835] msm_serial: driver initialized
  293. [ 1.652719] loop: module loaded
  294. [ 1.654475] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xac
  295. [ 1.654678] nand: Micron MT29F4G08ABBDAH4
  296. [ 1.661401] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
  297. [ 1.665324] 1 fixed-partitions partitions found on MTD device qcom_nand.0
  298. [ 1.672649] Creating 1 MTD partitions on "qcom_nand.0":
  299. [ 1.679643] 0x000000000000-0x000020000000 : "rootfs"
  300. [ 1.692753] random: fast init done
  301. [ 2.167172] random: crng init done
  302. [ 3.017883] mtd: device 0 (rootfs) set to be root filesystem
  303. [ 3.019079] mtdsplit: no squashfs found in "rootfs"
  304. [ 3.027054] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
  305. [ 3.031526] spi-nor spi0.0: mx25u3235f (4096 Kbytes)
  306. [ 3.034711] 13 fixed-partitions partitions found on MTD device spi0.0
  307. [ 3.039683] Creating 13 MTD partitions on "spi0.0":
  308. [ 3.046006] 0x000000000000-0x000000010000 : "0:SBL1"
  309. [ 3.051566] 0x000000010000-0x000000030000 : "0:MIBIB"
  310. [ 3.056811] 0x000000030000-0x000000060000 : "0:SBL2"
  311. [ 3.061585] 0x000000060000-0x000000090000 : "0:SBL3"
  312. [ 3.066678] 0x000000090000-0x0000000a0000 : "0:DDRCONFIG"
  313. [ 3.071563] 0x0000000a0000-0x0000000b0000 : "0:APPSBLENV"
  314. [ 3.076926] 0x0000000b0000-0x0000000c0000 : "0:ART"
  315. [ 3.082320] 0x0000000c0000-0x0000000f0000 : "0:TZ"
  316. [ 3.087100] 0x0000000f0000-0x000000110000 : "0:RPM"
  317. [ 3.091792] 0x000000110000-0x0000001a0000 : "0:APPSBL"
  318. [ 3.096722] 0x0000001a0000-0x000000200000 : "0:stat_cfg"
  319. [ 3.101752] 0x000000200000-0x000000300000 : "0:dyn_cfg"
  320. [ 3.107359] 0x000000300000-0x000000400000 : "0:dyn_cfg_backup"
  321. [ 3.227339] libphy: Fixed MDIO Bus: probed
  322. [ 3.229106] libphy: ipq8064_mdio_bus: probed
  323. [ 3.242287] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found
  324. [ 3.242348] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found
  325. [ 3.248909] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
  326. [ 3.255830] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
  327. [ 3.261371] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
  328. [ 3.268923] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
  329. [ 3.274643] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
  330. [ 3.282518] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
  331. [ 3.290338] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
  332. [ 3.296178] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
  333. [ 3.303462] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
  334. [ 3.310332] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
  335. [ 3.317861] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
  336. [ 3.324912] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
  337. [ 3.372457] libphy: stmmac: probed
  338. [ 3.375354] ipq806x-gmac-dwmac 37600000.ethernet: IRQ eth_wake_irq not found
  339. [ 3.375421] ipq806x-gmac-dwmac 37600000.ethernet: IRQ eth_lpi not found
  340. [ 3.382324] ipq806x-gmac-dwmac 37600000.ethernet: PTP uses main clock
  341. [ 3.389275] ipq806x-gmac-dwmac 37600000.ethernet: User ID: 0x10, Synopsys ID: 0x37
  342. [ 3.395032] ipq806x-gmac-dwmac 37600000.ethernet: DWMAC1000
  343. [ 3.402386] ipq806x-gmac-dwmac 37600000.ethernet: DMA HW capability register supported
  344. [ 3.408323] ipq806x-gmac-dwmac 37600000.ethernet: RX Checksum Offload Engine supported
  345. [ 3.416035] ipq806x-gmac-dwmac 37600000.ethernet: COE Type 2
  346. [ 3.423823] ipq806x-gmac-dwmac 37600000.ethernet: TX Checksum insertion supported
  347. [ 3.429730] ipq806x-gmac-dwmac 37600000.ethernet: Wake-Up On Lan supported
  348. [ 3.437104] ipq806x-gmac-dwmac 37600000.ethernet: Enhanced/Alternate descriptors
  349. [ 3.443792] ipq806x-gmac-dwmac 37600000.ethernet: Enabled extended descriptors
  350. [ 3.451444] ipq806x-gmac-dwmac 37600000.ethernet: Ring mode enabled
  351. [ 3.458471] ipq806x-gmac-dwmac 37600000.ethernet: Enable RX Mitigation via HW Watchdog Timer
  352. [ 3.505896] libphy: stmmac: probed
  353. [ 3.509013] i2c /dev entries driver
  354. [ 3.509726] i2c_qup 16680000.i2c: using default clock-frequency 100000
  355. [ 3.519040] sdhci: Secure Digital Host Controller Interface driver
  356. [ 3.519080] sdhci: Copyright(c) Pierre Ossman
  357. [ 3.524348] sdhci-pltfm: SDHCI platform and OF driver helper
  358. [ 3.531565] NET: Registered protocol family 10
  359. [ 3.536003] Segment Routing with IPv6
  360. [ 3.538848] NET: Registered protocol family 17
  361. [ 3.542784] 8021q: 802.1Q VLAN Support v1.8
  362. [ 3.547047] Registering SWP/SWPB emulation handler
  363. [ 3.579638] qcom_rpm 108000.rpm: RPM firmware 3.0.16777375
  364. [ 3.594088] s1a: Bringing 0uV into 1050000-1050000uV
  365. [ 3.594397] s1a: supplied by regulator-dummy
  366. [ 3.598358] s1b: Bringing 0uV into 1050000-1050000uV
  367. [ 3.602629] s1b: supplied by regulator-dummy
  368. [ 3.607523] s2a: Bringing 0uV into 800000-800000uV
  369. [ 3.611809] s2a: supplied by regulator-dummy
  370. [ 3.616403] s2b: Bringing 0uV into 800000-800000uV
  371. [ 3.620858] s2b: supplied by regulator-dummy
  372. [ 3.634940] thermal thermal_zone0: failed to read out thermal zone (-110)
  373. [ 3.648480] ubi0: attaching mtd0
  374. [ 11.892068] ubi0: scanning is finished
  375. [ 11.915392] ubi0: attached mtd0 (name "rootfs", size 512 MiB)
  376. [ 11.915416] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
  377. [ 11.920109] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
  378. [ 11.926942] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
  379. [ 11.933738] ubi0: good PEBs: 4096, bad PEBs: 0, corrupted PEBs: 0
  380. [ 11.940593] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
  381. [ 11.946834] ubi0: max/mean erase counter: 29/5, WL threshold: 4096, image sequence number: 1062653683
  382. [ 11.953882] ubi0: available PEBs: 0, total reserved PEBs: 4096, PEBs reserved for bad PEB handling: 80
  383. [ 11.963330] ubi0: background thread "ubi_bgt0d" started, PID 153
  384. [ 11.974801] block ubiblock0_1: created from ubi0:1(rootfs)
  385. [ 11.979655] UB▒[ 11.994443] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
  386. [ 11.995623] Freeing unused kernel memory: 1024K
  387. [ 12.035586] Run /sbin/init as init process
  388. [ 12.035619] with arguments:
  389. [ 12.038574] /sbin/init
  390. [ 12.041612] with environment:
  391. [ 12.044216] HOME=/
  392. [ 12.047356] TERM=linux
  393. [ 12.726285] init: Console is alive
  394. [ 12.726473] init: - watchdog -
  395. [ 12.728666] init: Watchdog has previously reset the system
  396. [ 13.740644] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  397. [ 13.768720] pps_ldisc: PPS line discipline registered
  398. [ 13.770108] genirq: irq_chip msmgpio did not update eff. affinity mask of irq 54
  399. [ 13.780844] tpm tpm0: starting up the TPM manually
  400. [ 13.863392] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  401. [ 13.866988] init: - preinit -
  402. [ 15.092077] ipq806x-gmac-dwmac 37400000.ethernet ethtmp: renamed from eth0
  403. [ 15.143161] ipq806x-gmac-dwmac 37600000.ethernet eth0: renamed from eth1
  404. [ 15.192855] ipq806x-gmac-dwmac 37400000.ethernet eth1: renamed from ethtmp
  405. [ 15.609776] ipq806x-gmac-dwmac 37600000.ethernet eth0: PHY [37000000.mdio-mii:02] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
  406. [ 15.611283] dwmac1000: Master AXI performs any burst length
  407. [ 15.620928] ipq806x-gmac-dwmac 37600000.ethernet eth0: No Safety Features support found
  408. [ 15.636241] ipq806x-gmac-dwmac 37600000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
  409. [ 15.636599] ipq806x-gmac-dwmac 37600000.ethernet eth0: registered PTP clock
  410. [ 15.645760] ipq806x-gmac-dwmac 37600000.ethernet eth0: configuring for phy/sgmii link mode
  411. Press the [f] key and hit [enter] to enter failsafe mode
  412. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  413. [ 19.810328] ipq806x-gmac-dwmac 37600000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
  414. [ 19.810384] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  415. [ 19.917188] UBIFS (ubi0:2): default file-system created
  416. [ 19.919307] UBIFS (ubi0:2): Mounting in unauthenticated mode
  417. [ 19.925140] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 234
  418. [ 20.125201] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
  419. [ 20.125265] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
  420. [ 20.132046] UBIFS (ubi0:2): FS size: 492412928 bytes (469 MiB, 3878 LEBs), journal size 24633344 bytes (23 MiB, 194 LEBs)
  421. [ 20.142050] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
  422. [ 20.152957] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 5ECB64D4-59DC-44AD-97E5-098FEEC9E054, small LPT model
  423. [ 20.164399] mount_root: overlay filesystem has not been fully initialized yet
  424. [ 20.171349] mount_root: switching to ubifs overlay
  425. [ 20.198404] urandom-seed: Seed file not found (/etc/urandom.seed)
  426. [ 20.418331] ipq806x-gmac-dwmac 37600000.ethernet eth0: Link is Down
  427. [ 20.429299] procd: - early -
  428. [ 20.429554] procd: - watchdog -
  429. [ 20.431471] procd: Watchdog has previously reset the system
  430. [ 21.051923] procd: - watchdog -
  431. [ 21.052179] procd: Watchdog has previously reset the system
  432. [ 21.094507] procd: - ubus -
  433. [ 21.348783] procd: - init -
  434. Please press Enter to activate this console.
  435. [ 21.976951] urngd: v1.0.2 started.
  436. [ 22.020490] kmodloader: loading kernel modules from /etc/modules.d/*
  437. [ 22.079184] hid: raw HID events driver (C) Jiri Kosina
  438. [ 22.080321] GACT probability on
  439. [ 22.084002] Mirror/redirect action on
  440. [ 22.092125] u32 classifier
  441. [ 22.092147] input device check on
  442. [ 22.093715] Actions configured
  443. [ 22.124099] Bluetooth: Core ver 2.22
  444. [ 22.124256] NET: Registered protocol family 31
  445. [ 22.126901] Bluetooth: HCI device and connection manager initialized
  446. [ 22.131016] Bluetooth: HCI socket layer initialized
  447. [ 22.137582] Bluetooth: L2CAP socket layer initialized
  448. [ 22.142140] Bluetooth: SCO socket layer initialized
  449. [ 22.149084] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  450. [ 22.152008] Bluetooth: BNEP filters: protocol multicast
  451. [ 22.157692] Bluetooth: BNEP socket layer initialized
  452. [ 22.167285] usbcore: registered new interface driver btusb
  453. [ 22.169974] Loading modules backported from Linux version v5.15.8-0-g43e577d7a2cb
  454. [ 22.173016] Backport generated by backports.git v5.15.8-1-0-g83f664bb
  455. [ 22.181676] Bluetooth: HCI UART driver ver 2.3
  456. [ 22.187061] Bluetooth: HCI UART protocol H4 registered
  457. [ 22.191326] Bluetooth: HCI UART protocol BCSP registered
  458. [ 22.196543] Bluetooth: HCI UART protocol ATH3K registered
  459. [ 22.203507] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  460. [ 22.207339] Bluetooth: HIDP socket layer initialized
  461. [ 22.233875] Bluetooth: RFCOMM TTY layer initialized
  462. [ 22.233926] Bluetooth: RFCOMM socket layer initialized
  463. [ 22.237704] Bluetooth: RFCOMM ver 1.11
  464. [ 22.271166] xt_time: kernel timezone is -0000
  465. [ 22.271747] usbcore: registered new interface driver ath3k
  466. [ 22.489845] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
  467. [ 22.489876] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <[email protected]>. All Rights Reserved.
  468. [ 22.522310] ath10k_pci 0000:01:00.0: assign IRQ: got 46
  469. [ 22.522358] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x40.
  470. [ 22.527113] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
  471. [ 22.534400] ath10k_pci 0000:01:00.0: enabling bus mastering
  472. [ 22.540986] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
  473. [ 23.943165] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
  474. [ 23.943230] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
  475. [ 23.956880] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9980-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 b36a12bf
  476. [ 24.112485] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:6 crc32 08fa09f2
  477. [ 25.261483] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
  478. [ 25.261523] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
  479. [ 25.342248] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
  480. [ 25.343007] ath10k_pci 0000:01:00.0: wmi print 'free: 31080 iram: 23028 sram: 9596'
  481. [ 26.106649] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
  482. [ 26.197202] ath: EEPROM regdomain sanitized
  483. [ 26.197249] ath: EEPROM regdomain: 0x64
  484. [ 26.200205] ath: EEPROM indicates we should expect a direct regpair map
  485. [ 26.204041] ath: Country alpha2 being used: 00
  486. [ 26.210741] ath: Regpair used: 0x64
  487. [ 26.221218] ath10k_pci 0001:01:00.0: assign IRQ: got 48
  488. [ 26.221292] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x40.
  489. [ 26.227285] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
  490. [ 26.233357] ath10k_pci 0001:01:00.0: enabling bus mastering
  491. [ 26.254974] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
  492. [ 27.598991] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002
  493. [ 27.599031] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
  494. [ 27.609413] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 b36a12bf
  495. [ 27.679899] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:4 crc32 08fa09f2
  496. [ 28.829458] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
  497. [ 28.829499] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
  498. [ 28.910121] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
  499. [ 28.910884] ath10k_pci 0001:01:00.0: wmi print 'free: 31080 iram: 23028 sram: 9596'
  500. [ 29.183437] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
  501. [ 29.277236] ath: EEPROM regdomain sanitized
  502. [ 29.277286] ath: EEPROM regdomain: 0x64
  503. [ 29.280242] ath: EEPROM indicates we should expect a direct regpair map
  504. [ 29.284080] ath: Country alpha2 being used: 00
  505. [ 29.290786] ath: Regpair used: 0x64
  506. [ 29.308560] kmodloader: done loading kernel modules from /etc/modules.d/*
  507. [ 32.662792] [xx_custom] INFO: Applying custom default configuration
  508. [ 32.663368] [xx_custom] INFO: Setting hostname based on MAC address
  509. [ 32.688750] [xx_custom] INFO: Applying network configuration
  510. [ 32.739528] [xx_custom] PASSWD: Setting root password to 9035ef223d4143c3fd3ae242
  511. [ 32.825640] [xx_custom] INFO: Finished applying custom default configuration.
  512. [ 40.249667] ipq806x-gmac-dwmac 37600000.ethernet eth0: PHY [37000000.mdio-mii:02] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
  513. [ 40.250298] dwmac1000: Master AXI performs any burst length
  514. [ 40.260786] ipq806x-gmac-dwmac 37600000.ethernet eth0: No Safety Features support found
  515. [ 40.276029] ipq806x-gmac-dwmac 37600000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
  516. [ 40.276162] ipq806x-gmac-dwmac 37600000.ethernet eth0: registered PTP clock
  517. [ 40.283880] ipq806x-gmac-dwmac 37600000.ethernet eth0: configuring for phy/sgmii link mode
  518. [ 40.293838] br-lan: port 1(eth0) entered blocking state
  519. [ 40.299221] br-lan: port 1(eth0) entered disabled state
  520. [ 40.304459] device eth0 entered promiscuous mode
  521. [ 40.401524] ipq806x-gmac-dwmac 37400000.ethernet eth1: PHY [37000000.mdio-mii:01] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
  522. [ 40.402166] dwmac1000: Master AXI performs any burst length
  523. [ 40.412639] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
  524. [ 40.427907] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
  525. [ 40.428040] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
  526. [ 40.436303] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for phy/sgmii link mode
  527. [ 40.445911] br-lan: port 2(eth1) entered blocking state
  528. [ 40.450943] br-lan: port 2(eth1) entered disabled state
  529. [ 40.456416] device eth1 entered promiscuous mode
  530. [ 40.461384] br-lan: port 2(eth1) entered blocking state
  531. [ 40.466292] br-lan: port 2(eth1) entered forwarding state
  532. [ 40.471189] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  533. [ 41.288486] br-lan: port 2(eth1) entered disabled state
  534. [ 42.394221] device eth0 left promiscuous mode
  535. [ 42.394290] br-lan: port 1(eth0) entered disabled state
  536. [ 42.419295] device eth1 left promiscuous mode
  537. [ 42.419370] br-lan: port 2(eth1) entered disabled state
  538. [ 42.694699] ipq806x-gmac-dwmac 37600000.ethernet eth0: PHY [37000000.mdio-mii:02] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
  539. [ 42.695320] dwmac1000: Master AXI performs any burst length
  540. [ 42.705766] ipq806x-gmac-dwmac 37600000.ethernet eth0: No Safety Features support found
  541. [ 42.720985] ipq806x-gmac-dwmac 37600000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
  542. [ 42.721153] ipq806x-gmac-dwmac 37600000.ethernet eth0: registered PTP clock
  543. [ 42.729068] ipq806x-gmac-dwmac 37600000.ethernet eth0: configuring for phy/sgmii link mode
  544. [ 42.743294] br-lan: port 1(eth0) entered blocking state
  545. [ 42.744025] br-lan: port 1(eth0) entered disabled state
  546. [ 42.749483] device eth0 entered promiscuous mode
  547. [ 42.839932] ipq806x-gmac-dwmac 37400000.ethernet eth1: PHY [37000000.mdio-mii:01] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
  548. [ 42.840554] dwmac1000: Master AXI performs any burst length
  549. [ 42.851006] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
  550. [ 42.866306] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
  551. [ 42.866441] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
  552. [ 42.874164] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for phy/sgmii link mode
  553. [ 42.884218] br-lan: port 2(eth1) entered blocking state
  554. [ 42.889450] br-lan: port 2(eth1) entered disabled state
  555. [ 42.894720] device eth1 entered promiscuous mode
  556. [ 45.895280] ipq806x-gmac-dwmac 37600000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
  557. [ 45.895364] br-lan: port 1(eth0) entered blocking state
  558. [ 45.903146] br-lan: port 1(eth0) entered forwarding state
  559. [ 45.908683] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  560. ​
  561. ​
  562. ​
  563. BusyBox v1.35.0 (2022-01-17 06:44:52 UTC) built-in shell (ash)
  564. ​
  565. _______ ________ __
  566. | |.-----.-----.-----.| | | |.----.| |_
  567. | - || _ | -__| || | | || _|| _|
  568. |_______|| __|_____|__|__||________||__| |____|
  569. |__| W I R E L E S S F R E E D O M
  570. -----------------------------------------------------
  571. OpenWrt apx530, r18592-6e02b3c482
  572. -----------------------------------------------------
  573. root@apx530-346182 / #

Edit this Snippet