Snippet content copied to clipboard.
Are you sure to delete this snippet? No, don't delete
  1. U-Boot 2018.09 (Dec 05 2019 - 10:12:58 -0800)
  2. ​
  3. SoC: LS1023AE Rev1.1 (0x87920811)
  4. Clock Configuration:
  5. CPU0(A53):1000 MHz CPU1(A53):1000 MHz
  6. Bus: 300 MHz DDR: 1600 MT/s FMAN: 500 MHz
  7. Reset Configuration Word (RCW):
  8. 00000000: 0610000a 0a000000 00000000 00000000
  9. 00000010: 45580002 00000012 40044000 c1002000
  10. 00000020: 00000000 00000000 00000000 0003effe
  11. 00000030: 20004504 0418320a 00000096 00000001
  12. Model: LS1043A QDS Board - T40/T20
  13. Board: LS1043AQDS, boot from vBank: 0
  14. I2C: ready
  15. DRAM: Initializing DDR...
  16. Detected UDIMM Fixed DDR4 on board
  17. 1.9 GiB (DDR4, 32-bit, CL=11, ECC off)
  18. Using SERDES1 Protocol: 17752 (0x4558)
  19. SEC Firmware: Bad firmware image (not a FIT image)
  20. Waking secondary cores to start from fbd35000
  21. All (2) cores are up.
  22. MMC: FSL_SDHC: 0
  23. Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
  24. OK
  25. In: serial
  26. Out: serial
  27. Err: serial
  28. Net: SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
  29. Fman1: Uploading microcode version 108.4.9
  30. PCIe0: pcie@3400000 Root Complex: no link
  31. PCIe1: pcie@3500000 Root Complex: no link
  32. PCIe2: pcie@3600000 disabled
  33. FM1@DTSEC1 [PRIME], FM1@DTSEC2, FM1@DTSEC3, FM1@DTSEC5, FM1@DTSEC6
  34. ### main_loop entered: bootdelay=5
  35. ​
  36. ### main_loop: bootcmd="printenv"
  37. ​
  38. WatchGuard U-Boot 2018.09 - Dec 05 2019 10:12:58
  39. ​
  40. +-------------------------------------------------------------------------+
  41. |WatchGuard (SYSA) |
  42. |WatchGuard (SYSB Recovery/Diagnostic Mode) |
  43. | |
  44. | |
  45. | |
  46. | |
  47. | |
  48. | |
  49. | |
  50. | |
  51. | |
  52. +-------------------------------------------------------------------------+
  53. ​
  54. Use the ^ and v keys to select which entry is highlighted.
  55. Press enter to boot the selected OS.
  56. ​
  57. ​
  58. ​
  59. ​
  60. ​
  61. ​
  62. password> ass
  63. ​
  64. => printenv
  65. SysARoot=mmcblk0p3
  66. SysBRoot=mmcblk0p2
  67. WGKernelfile=kernel_T20_T40_prod.itb
  68. arch=arm
  69. baudrate=115200
  70. board=ls1043aqds_t20
  71. board_name=ls1043aqds_t20
  72. boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
  73. boot_efi_binary=if fdt addr ${fdt_addr_r}; then bootefi bootmgr ${fdt_addr_r};else bootefi bootmgr ${fdtcontroladdr};fi;load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} efi/boot/bootaa64.efi; if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r};else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi
  74. boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf
  75. boot_net_pci_enum=pci enum
  76. boot_net_usb_start=usb start
  77. boot_os=y
  78. boot_prefixes=/ /boot/
  79. boot_script_dhcp=boot.scr.uimg
  80. boot_script_hdr=hdr_ls1043ardb_bs.out
  81. boot_scripts=ls1043ardb_boot.scr
  82. boot_targets=mmc0 usb0
  83. bootargs=console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)
  84. bootcmd=printenv
  85. bootcmd_mmc0=setenv devnum 0; run mmc_boot
  86. bootcmd_usb0=setenv devnum 0; run usb_boot
  87. bootdelay=5
  88. consoledev=ttyS0
  89. cpu=armv8
  90. distro_bootcmd=setenv scsi_need_init; for target in ${boot_targets}; do run bootcmd_${target}; done
  91. efi_dtb_prefixes=/ /dtb/ /dtb/current/
  92. eth1addr=00:0B:6B:01:01:02
  93. eth2addr=00:0B:6B:01:01:03
  94. eth3addr=00:0B:6B:01:01:04
  95. eth4addr=00:0B:6B:01:01:05
  96. eth5addr=00:0B:6B:01:01:06
  97. ethact=FM1@DTSEC1
  98. ethaddr=00:0B:6B:01:01:01
  99. ethprime=FM1@DTSEC1
  100. fdt_addr=0x64f00000
  101. fdt_addr_r=0x90000000
  102. fdt_high=0xffffffffffffffff
  103. fdtcontroladdr=fbc2e288
  104. fdtheader_addr_r=0x80100000
  105. flash_bootloader=tftp 0x82000000 u-boot_ls1043aqds_wg_t20_qspi.bin;sf probe 0; sf erase 0 0x100000; sf write 0x82000000 0 $filesize;sf read 0x80000000 0 $filesize; cmp.b 0x82000000 0x80000000 $filesize;
  106. fman_ucode=fbc3d540
  107. hwconfig=fsl_ddr:bank_intlv=auto
  108. initrd_high=0xffffffffffffffff
  109. ipaddr=192.168.1.1
  110. kernel_addr=0x61000000
  111. kernel_addr_r=0x81000000
  112. kernel_addr_sd=0x8000
  113. kernel_size=0x2800000
  114. kernel_size_sd=0x14000
  115. kernel_start=0x1000000
  116. kernelhdr_addr_sd=0x4000
  117. kernelhdr_size_sd=0x10
  118. kernelheader_addr=0x60800000
  119. kernelheader_addr_r=0x80200000
  120. kernelheader_size=0x40000
  121. kernelheader_start=0x800000
  122. load_addr=0xa0000000
  123. load_efi_dtb=load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} ${prefix}${efi_fdtfile}
  124. loadaddr=82000000
  125. mmc_boot=if mmc dev ${devnum}; then setenv devtype mmc; run scan_dev_for_boot_part; fi
  126. mtdparts=mtdparts=spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)
  127. netmask=255.255.255.0
  128. nuke_env=sf probe 0;sf erase 0x200000 10000;
  129. scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;run scan_dev_for_efi;
  130. scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done
  131. scan_dev_for_efi=setenv efi_fdtfile ${fdtfile}; for prefix in ${efi_dtb_prefixes}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${efi_fdtfile}; then run load_efi_dtb; fi;done;if test -e ${devtype} ${devnum}:${distro_bootpart} efi/boot/bootaa64.efi; then echo Found EFI removable media binary efi/boot/bootaa64.efi; run boot_efi_binary; echo EFI LOAD FAILED: continuing...; fi; setenv efi_fdtfile
  132. scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi
  133. scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
  134. scriptaddr=0x80000000
  135. scripthdraddr=0x80080000
  136. scsi_boot=run scsi_init; if scsi dev ${devnum}; then setenv devtype scsi; run scan_dev_for_boot_part; fi
  137. scsi_init=if ${scsi_need_init}; then setenv scsi_need_init false; scsi scan; fi
  138. serveraddr=10.0.1.13;
  139. serverip=192.168.1.100
  140. soc=fsl-layerscape
  141. stderr=serial
  142. stdin=serial
  143. stdout=serial
  144. usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run scan_dev_for_boot_part; fi
  145. vendor=freescale
  146. wgBootRecovery=setenv bootargs wgmode=safe root=/dev/$SysARoot rw console=$consoledev,$baudrate $othbootargs earlycon=uart8250,mmio,0x21c0500; mmc info; ext2load mmc 0:3 $loadaddr $WGKernelfile; bootm $loadaddr;
  147. wgBootSysA=setenv bootargs root=/dev/$SysARoot rw rootdelay=2 console=$consoledev,$baudrate $othbootargs earlycon=uart8250,mmio,0x21c0500; mmc info; ext2load mmc 0:3 $loadaddr $WGKernelfile; bootm $loadaddr;
  148. wgBootSysB=setenv bootargs root=/dev/$SysBRoot rw rootdelay=2 console=$consoledev,$baudrate $othbootargs earlycon=uart8250,mmio,0x21c0500; mmc info; ext2load mmc 0:2 $loadaddr $WGKernelfile; bootm $loadaddr;
  149. ​
  150. Environment size: 5011/8188 bytes
  151. ​
  152. => mmc info
  153. Device: FSL_SDHC
  154. Manufacturer ID: 70
  155. OEM: 100
  156. Name: M6270
  157. Bus Speed: 52000000
  158. Mode : MMC High Speed (52MHz)
  159. Rd Block Len: 512
  160. MMC version 5.0
  161. High Capacity: Yes
  162. Capacity: 3.6 GiB
  163. Bus Width: 4-bit
  164. Erase Group Size: 512 KiB
  165. HC WP Group Size: 4 MiB
  166. User Capacity: 3.6 GiB WRREL
  167. Boot Capacity: 2 MiB ENH
  168. RPMB Capacity: 512 KiB ENH
  169. => mmc dev
  170. switch to partitions #0, OK
  171. mmc0(part 0) is current device
  172. => help
  173. 74lv164 - 74lv164 control
  174. ? - alias for 'help'
  175. base - print or set address offset
  176. bdinfo - print Board Info structure
  177. blkcache- block cache diagnostics and control
  178. boot - boot default, i.e., run 'bootcmd'
  179. bootd - boot default, i.e., run 'bootcmd'
  180. bootefi - Boots an EFI payload from memory
  181. bootelf - Boot from an ELF image in memory
  182. booti - boot arm64 Linux Image image from memory
  183. bootm - boot application image from memory
  184. bootp - boot image via network using BOOTP/TFTP protocol
  185. bootvx - Boot vxWorks from an ELF image
  186. bootz - boot Linux zImage image from memory
  187. cmp - memory compare
  188. coninfo - print console devices and information
  189. cp - memory copy
  190. cpu - Multiprocessor CPU boot manipulation and release
  191. crc32 - checksum calculation
  192. date - get/set/reset date & time
  193. dcache - enable or disable data cache
  194. dhcp - boot image via network using DHCP/TFTP protocol
  195. echo - echo args to console
  196. editenv - edit environment variable
  197. env - environment handling commands
  198. erase - erase FLASH memory
  199. exit - exit script
  200. ext2load- load binary file from a Ext2 filesystem
  201. ext2ls - list files in a directory (default /)
  202. ext4load- load binary file from a Ext4 filesystem
  203. ext4ls - list files in a directory (default /)
  204. ext4size- determine a file's size
  205. false - do nothing, unsuccessfully
  206. fatinfo - print information about filesystem
  207. fatload - load binary file from a dos filesystem
  208. fatls - list files in a directory (default /)
  209. fatsize - determine a file's size
  210. fdt - flattened device tree utility commands
  211. flinfo - print FLASH memory information
  212. fstype - Look up a filesystem type
  213. go - start application at address 'addr'
  214. gpio - query and control gpio pins
  215. gpt - GUID Partition Table
  216. grepenv - search environment variables
  217. gzwrite - unzip and write memory to block device
  218. hash - compute hash message digest
  219. help - print command description/usage
  220. i2c - I2C sub-system
  221. icache - enable or disable instruction cache
  222. iminfo - print header information for application image
  223. imxtract- extract a part of a multi-image
  224. itest - return true/false on integer compare
  225. led - LED control
  226. load - load binary file from a filesystem
  227. loadb - load binary file over serial line (kermit mode)
  228. loads - load S-Record file over serial line
  229. loadx - load binary file over serial line (xmodem mode)
  230. loady - load binary file over serial line (ymodem mode)
  231. loop - infinite loop on address range
  232. ls - list files in a directory (default /)
  233. lzmadec - lzma uncompress a memory region
  234. md - memory display
  235. mdio - MDIO utility commands
  236. meminfo - display memory information
  237. mii - MII utility commands
  238. mm - memory modify (auto-incrementing address)
  239. mmc - MMC sub system
  240. mmcinfo - display MMC info
  241. mtest - simple RAM read/write test
  242. mw - memory write (fill)
  243. nfs - boot image via network using NFS protocol
  244. nm - memory modify (constant address)
  245. part - disk partition related commands
  246. pci - list and access PCI Configuration Space
  247. ping - send ICMP ECHO_REQUEST to network host
  248. printenv- print environment variables
  249. protect - enable or disable FLASH write protection
  250. pxe - commands to get and boot from pxe files
  251. qixis_reset- Reset the board using the FPGA sequencer
  252. reset - Perform RESET of the CPU
  253. run - run commands in an environment variable
  254. save - save file to a filesystem
  255. saveenv - save environment variables to persistent storage
  256. scsi - SCSI sub-system
  257. scsiboot- boot from SCSI device
  258. setenv - set environment variables
  259. setexpr - set environment variable as the result of eval expression
  260. sf - SPI flash sub-system
  261. showvar - print local hushshell variables
  262. size - determine a file's size
  263. sleep - delay execution for some time
  264. source - run script from memory
  265. sysboot - command to get and boot from syslinux files
  266. test - minimal test like /bin/sh
  267. tftpboot- boot image via network using TFTP protocol
  268. true - do nothing, successfully
  269. unzip - unzip a memory region
  270. usb - USB sub-system
  271. usbboot - boot from USB device
  272. vdd_override- override VDD
  273. vdd_read- read VDD
  274. version - print monitor, compiler and linker version
  275. => ext4ls mmc 0:3
  276. <DIR> 1024 .
  277. <DIR> 1024 ..
  278. <DIR> 12288 lost+found
  279. 217 info.txt
  280. <DIR> 1024 proc
  281. <DIR> 1024 initrd
  282. <DIR> 1024 tools
  283. <DIR> 1024 usr
  284. <DIR> 1024 root
  285. <DIR> 3072 sbin
  286. <DIR> 1024 boot
  287. <DIR> 1024 home
  288. <DIR> 16384 dev
  289. <DIR> 1024 sysfs
  290. <SYM> 3 lib64
  291. <DIR> 1024 var
  292. <DIR> 3072 etc
  293. <DIR> 15360 lib
  294. <DIR> 1024 pending
  295. <DIR> 1024 bin
  296. <DIR> 1024 tmp
  297. <DIR> 1024 opt
  298. <DIR> 1024 sys
  299. 10420940 kernel_T20_T40.itb
  300. 10420940 kernel_T20_T40_prod.itb
  301. <DIR> 1024 data2
  302. => ext4ls mmc 0:3 etc
  303. <DIR> 3072 .
  304. <DIR> 1024 ..
  305. 0 diskpt_once
  306. <SYM> 19 default.xml
  307. 512 random-seed
  308. 5762 CRYPTO-POST.req
  309. 7052 tcsd.conf
  310. <DIR> 1024 ssh
  311. <DIR> 1024 mdev.d
  312. 178 fw_env.config
  313. <DIR> 1024 runlevel
  314. <DIR> 1024 oss-conf
  315. 2597 services
  316. <DIR> 1024 sysa
  317. <DIR> 1024 wgsync
  318. 118 wapid.conf
  319. <SYM> 17 mdev.conf
  320. <DIR> 1024 defaults
  321. 39119 dhcp_fingerprints.conf
  322. <SYM> 28 snmpd.conf
  323. <DIR> 1024 nginx
  324. <DIR> 1024 raddb
  325. <DIR> 1024 fonts
  326. 142 lickey.pem
  327. 1235 passwd
  328. <DIR> 1024 ppp
  329. <DIR> 1024 csfc_post
  330. <DIR> 1024 libnl
  331. 972 conntrackd.conf
  332. <DIR> 1024 schema
  333. 443 loggerd-modules.conf
  334. 1325 country_spec_00.xml
  335. <DIR> 1024 iproute2
  336. <DIR> 1024 json-schema
  337. 6995 CRYPTO-POST.rsp
  338. 237 group
  339. <DIR> 1024 proxy
  340. <DIR> 3072 inittab.d
  341. <DIR> 1024 stylesheet
  342. 451 diag_access_public.pem
  343. <DIR> 1024 tdts
  344. 259 nsswitch.conf
  345. 98 code-signature
  346. <DIR> 1024 rsyncd-modules
  347. 587219 defaultT40.xml
  348. 314 netdbg.cfg
  349. 11755 termcap
  350. 686 protocols
  351. <DIR> 1024 tdr
  352. 520 guac-standalone.cfg
  353. 2802 country_spec_us.xml
  354. 32 shells
  355. 1362 ethertypes
  356. <DIR> 1024 wg
  357. 605784 magic.mgc
  358. 61 wvmodemscan.conf
  359. 33 snmp-wrap.conf
  360. <SYM> 12 mtab
  361. 587199 defaultT20.xml
  362. <SYM> 16 wvdial.conf
  363. 160 hosts-default
  364. 1 lsb-release
  365. 355 hmacsums.txt
  366. <DIR> 1024 radiusclient
  367. 123348 product_table.json
  368. <SYM> 17 localtime
  369. <DIR> 1024 fmc
  370. <SYM> 20 resolv.conf
  371. <DIR> 3072 licenses
  372. 853 fstab
  373. <DIR> 1024 pam.d
  374. <SYM> 10 hosts
  375. 460 rsyncd.conf
  376. 178 codesign-public.pem
  377. 192429 code-signed
  378. => setenv wgBootSysA 'setenv bootargs root=/dev/$SysARoot rw rootdelay=2 console=$consoledev,$baudrate earlycon=uart8250,mmio,0x21c0500 $othbootargs; mmc info; ext2load mmc 0:3 $loadaddr $WGKernelfile; bootm $loadaddr;'
  379. => setenv othbootargs 'loglevel=8 single'
  380. => saveenv
  381. Saving Environment to SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 64 KiB, total 4 MiB
  382. Erasing SPI flash...Writing to SPI flash...done
  383. OK
  384. => run wgBootSysA
  385. Device: FSL_SDHC
  386. Manufacturer ID: 70
  387. OEM: 100
  388. Name: M6270
  389. Bus Speed: 52000000
  390. Mode : MMC High Speed (52MHz)
  391. Rd Block Len: 512
  392. MMC version 5.0
  393. High Capacity: Yes
  394. Capacity: 3.6 GiB
  395. Bus Width: 4-bit
  396. Erase Group Size: 512 KiB
  397. HC WP Group Size: 4 MiB
  398. User Capacity: 3.6 GiB WRREL
  399. Boot Capacity: 2 MiB ENH
  400. RPMB Capacity: 512 KiB ENH
  401. 10420940 bytes read in 612 ms (16.2 MiB/s)
  402. ## Loading kernel from FIT Image at 82000000 ...
  403. Using 'conf@1' configuration
  404. Trying 'kernel@1' kernel subimage
  405. Description: WatchGuard Kernel
  406. Created: 2022-01--8 1:26:08 UTC
  407. Type: Kernel Image
  408. Compression: gzip compressed
  409. Data Start: 0x820000cc
  410. Data Size: 10386949 Bytes = 9.9 MiB
  411. Architecture: AArch64
  412. OS: Linux
  413. Load Address: 0x80080000
  414. Entry Point: 0x80080000
  415. Hash algo: crc32
  416. Hash value: 9b4fb984
  417. Hash algo: sha1
  418. Hash value: fc46e7e04922b05ce0863c4c05ae2f62b964d1d8
  419. Verifying Hash Integrity ... crc32+ sha1+ OK
  420. ## Loading fdt from FIT Image at 82000000 ...
  421. Using 'conf@1' configuration
  422. Trying 'fdt@1' fdt subimage
  423. Description: Flattened Device Tree blob
  424. Created: 2022-01--8 1:26:08 UTC
  425. Type: Flat Device Tree
  426. Compression: uncompressed
  427. Data Start: 0x829e8000
  428. Data Size: 32642 Bytes = 31.9 KiB
  429. Architecture: AArch64
  430. Load Address: 0x90000000
  431. Hash algo: crc32
  432. Hash value: 8ac87d7b
  433. Hash algo: sha1
  434. Hash value: 01635f39bd4bb64375dce2d6e03b2bda97f89275
  435. Verifying Hash Integrity ... crc32+ sha1+ OK
  436. Loading fdt from 0x829e8000 to 0x90000000
  437. Booting using the fdt blob at 0x90000000
  438. Uncompressing Kernel Image ... OK
  439. Using Device Tree in place at 0000000090000000, end 000000009001af81
  440. WARNING: SEC firmware not running, no kaslr-seed
  441. WARNING failed to get smmu node: FDT_ERR_NOTFOUND
  442. WARNING failed to get smmu node: FDT_ERR_NOTFOUND
  443. ​
  444. Starting kernel ...
  445. ​
  446. [ 0.000000] Booting Linux on physical CPU 0x0
  447. [ 0.000000] Linux version 4.14.83 (release@cmrb06) (gcc version 6.5.0 (crosstool-NG 1.23.0.580-eb72b4e)) #1 SMP PREEMPT Wed Dec 22 17:22:15 PST 2021
  448. [ 0.000000] Boot CPU: AArch64 Processor [410fd034]
  449. [ 0.000000] Machine model: LS1043A RDB Board - T40
  450. [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0500 (options '')
  451. [ 0.000000] bootconsole [uart8250] enabled
  452. [ 0.000000] efi: Getting EFI parameters from FDT:
  453. [ 0.000000] efi: UEFI not found.
  454. [ 0.000000] crashkernel reserved: 0x00000000f8600000 - 0x00000000fbe00000 (56 MB)
  455. [ 0.000000] OF: reserved mem: initialized node qman-fqd, compatible id fsl,qman-fqd
  456. [ 0.000000] OF: reserved mem: initialized node qman-pfdr, compatible id fsl,qman-pfdr
  457. [ 0.000000] OF: reserved mem: initialized node bman-fbpr, compatible id fsl,bman-fbpr
  458. [ 0.000000] cma: Reserved 16 MiB at 0x00000000f4000000
  459. [ 0.000000] On node 0 totalpages: 494080
  460. [ 0.000000] DMA zone: 6937 pages used for memmap
  461. [ 0.000000] DMA zone: 0 pages reserved
  462. [ 0.000000] DMA zone: 494080 pages, LIFO batch:31
  463. [ 0.000000] percpu: Embedded 22 pages/cpu @ffff800078575000 s50904 r8192 d31016 u90112
  464. [ 0.000000] pcpu-alloc: s50904 r8192 d31016 u90112 alloc=22*4096
  465. [ 0.000000] pcpu-alloc: [0] 0 [0] 1
  466. [ 0.000000] Detected VIPT I-cache on CPU0
  467. [ 0.000000] CPU features: enabling workaround for ARM erratum 845719
  468. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 487143
  469. [ 0.000000] Kernel command line: root=/dev/mmcblk0p3 rw rootdelay=2 console=ttyS0,115200 earlycon=uart8250,mmio,0x21c0500 loglevel=8 single
  470. [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
  471. [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
  472. [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
  473. [ 0.000000] Memory: 1852420K/1976320K available (7996K kernel code, 518K rwdata, 2944K rodata, 5376K init, 849K bss, 107516K reserved, 16384K cma-reserved)
  474. [ 0.000000] Virtual kernel memory layout:
  475. [ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB)
  476. [ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB)
  477. [ 0.000000] .text : 0xffff000008080000 - 0xffff000008850000 ( 8000 KB)
  478. [ 0.000000] .rodata : 0xffff000008850000 - 0xffff000008b40000 ( 3008 KB)
  479. [ 0.000000] .init : 0xffff000008b40000 - 0xffff000009080000 ( 5376 KB)
  480. [ 0.000000] .data : 0xffff000009080000 - 0xffff000009101a00 ( 519 KB)
  481. [ 0.000000] .bss : 0xffff000009101a00 - 0xffff0000091d6108 ( 850 KB)
  482. [ 0.000000] fixed : 0xffff7dfffe7fb000 - 0xffff7dfffec00000 ( 4116 KB)
  483. [ 0.000000] PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB)
  484. [ 0.000000] vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum)
  485. [ 0.000000] 0xffff7e0000000000 - 0xffff7e0001b19000 ( 27 MB actual)
  486. [ 0.000000] memory : 0xffff800000000000 - 0xffff80007be00000 ( 1982 MB)
  487. [ 0.000000] Preemptible hierarchical RCU implementation.
  488. [ 0.000000] RCU event tracing is enabled.
  489. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
  490. [ 0.000000] Tasks RCU enabled.
  491. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
  492. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
  493. [ 0.000000] GIC: Adjusting CPU interface base to 0x000000000142f000
  494. [ 0.000000] GIC: Using split EOI/Deactivate mode
  495. [ 0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858
  496. [ 0.000000] arch_timer: CPU0: Trapping CNTVCT access
  497. [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
  498. [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
  499. [ 0.000004] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
  500. [ 0.008589] Console: colour dummy device 80x25
  501. [ 0.013079] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000)
  502. [ 0.023506] pid_max: default: 32768 minimum: 301
  503. [ 0.028218] Security Framework initialized
  504. [ 0.032386] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
  505. [ 0.039145] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
  506. [ 0.062384] ASID allocator initialised with 32768 entries
  507. [ 0.075844] Hierarchical SRCU implementation.
  508. [ 0.088268] WG CPU Model 1043 Count 4
  509. [ 0.092035] WG CRASH MIN RESERVE 56 MB
  510. [ 0.096073]
  511. [ 0.096073] wg_kernel_init: Built Dec 22 2021 17:11:46
  512. [ 0.103071] EFI services will not be available.
  513. [ 0.115654] smp: Bringing up secondary CPUs ...
  514. [ 0.148332] Detected VIPT I-cache on CPU1
  515. [ 0.148364] arch_timer: CPU1: Trapping CNTVCT access
  516. [ 0.148370] CPU1: Booted secondary processor [410fd034]
  517. [ 0.148433] smp: Brought up 1 node, 2 CPUs
  518. [ 0.166866] SMP: Total of 2 processors activated.
  519. [ 0.171606] CPU features: detected feature: 32-bit EL0 Support
  520. [ 0.177489] CPU features: detected feature: Kernel page table isolation (KPTI)
  521. [ 0.193439] CPU: All CPU(s) started at EL2
  522. [ 0.197572] alternatives: patching kernel code
  523. [ 0.202276] wg_check_smp_cpus: CPUs offline, found 2, expected 4.
  524. [ 0.202280] wg_check_smp_cpus: CPUs offline, found 2, expected 4.
  525. [ 0.219550] random: get_random_u32 called from bucket_table_alloc+0xf8/0x280 with crng_init=0
  526. [ 0.228387] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
  527. [ 0.238207] futex hash table entries: 512 (order: 3, 32768 bytes)
  528. [ 0.244901] alloc_chrdev_region: 254:0 gpiochip
  529. [ 0.249732] DMI not present or invalid.
  530. [ 0.253784] NET: Registered protocol family 16
  531. [ 0.258606] alloc_chrdev_region: 253:0 fsl_mc_bus
  532. [ 0.267552] cpuidle: using governor menu
  533. [ 0.271965] Bman ver:0a02,02,01
  534. [ 0.277516] qman-fqd addr 0x00000000f8000000 size 0x400000
  535. [ 0.283045] qman-pfdr addr 0x00000000f6000000 size 0x2000000
  536. [ 0.288769] Qman ver:0a01,03,02,00
  537. [ 0.292339] vdso: 2 pages (1 code @ ffff000008857000, 1 data @ ffff000009084000)
  538. [ 0.299801] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  539. [ 0.307508] DMA: preallocated 256 KiB pool for atomic allocations
  540. [ 0.313741] Serial: AMBA PL011 UART driver
  541. [ 0.318846] Machine: LS1043A RDB Board - T40
  542. [ 0.323150] SoC family: QorIQ LS1043A
  543. [ 0.326830] SoC ID: svr:0x87920811, Revision: 1.1
  544. [ 0.355544] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
  545. [ 0.363974] ACPI: Interpreter disabled.
  546. [ 0.369962] alloc_chrdev_region: 252:0 tpm
  547. [ 0.374791] misc_register: 10, 63 vga_arbiter
  548. [ 0.379404] vgaarb: loaded
  549. [ 0.382288] SCSI subsystem initialized
  550. [ 0.386185] libata version 3.00 loaded.
  551. [ 0.390238] usbcore: registered new interface driver usbfs
  552. [ 0.395836] usbcore: registered new interface driver hub
  553. [ 0.401231] usbcore: registered new device driver usb
  554. [ 0.406391] alloc_chrdev_region: 251:0 rtc
  555. [ 0.411237] i2c i2c-0: IMX I2C adapter registered
  556. [ 0.416023] i2c i2c-0: using dma0chan16 (tx) and dma0chan17 (rx) for DMA transfers
  557. [ 0.423906] alloc_chrdev_region: 250:0 pps
  558. [ 0.428209] pps_core: LinuxPPS API ver. 1 registered
  559. [ 0.433225] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
  560. [ 0.442441] alloc_chrdev_region: 249:0 ptp
  561. [ 0.446745] PTP clock support registered
  562. [ 0.450784] dmi: Firmware registration failed.
  563. [ 0.455315] bman-fbpr addr 0x00000000f5000000 size 0x1000000
  564. [ 0.461044] Bman err interrupt handler present
  565. [ 0.466124] Bman portal initialised, cpu 0
  566. [ 0.470332] Bman portal initialised, cpu 1
  567. [ 0.474461] Bman portals initialised
  568. [ 0.479224] Qman err interrupt handler present
  569. [ 0.483941] QMan: Allocated lookup table at ffff000009fe5000, entry count 65537
  570. [ 0.491883] Qman portal initialised, cpu 0
  571. [ 0.496082] Qman portal initialised, cpu 1
  572. [ 0.500209] Qman portals initialised
  573. [ 0.503914] Bman: BPID allocator includes range 32:32
  574. [ 0.509088] Qman: FQID allocator includes range 256:256
  575. [ 0.514352] Qman: FQID allocator includes range 32768:32768
  576. [ 0.520048] Qman: CGRID allocator includes range 0:256
  577. [ 0.525426] Qman: pool channel allocator includes range 1025:15
  578. [ 0.531519] No USDPAA memory, no 'fsl,usdpaa-mem' in device-tree
  579. [ 0.537610] fsl-ifc 1530000.ifc: Freescale Integrated Flash Controller
  580. [ 0.544200] fsl-ifc 1530000.ifc: IFC version 1.4, 8 banks
  581. [ 0.549880] alloc_chrdev_region: 248:0 iio
  582. [ 0.554647] alloc_chrdev_region: 247:0 watchdog
  583. [ 0.559535] clocksource: Switched to clocksource arch_sys_counter
  584. [ 0.565854] pnp: PnP ACPI: disabled
  585. [ 0.573486] NET: Registered protocol family 2
  586. [ 0.578266] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  587. [ 0.585671] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
  588. [ 0.592588] TCP: Hash tables configured (established 16384 bind 16384)
  589. [ 0.599244] UDP hash table entries: 1024 (order: 3, 32768 bytes)
  590. [ 0.605342] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
  591. [ 0.611968] NET: Registered protocol family 1
  592. [ 0.616375] PCI: CLS 0 bytes, default 64
  593. [ 0.834513] hw perfevents: failed to parse interrupt-affinity[2] for pmu
  594. [ 0.841297] hw perfevents: /pmu: failed to register PMU devices!
  595. [ 0.847369] armv8-pmu: probe of pmu failed with error -22
  596. [ 0.858866] audit: initializing netlink subsys (disabled)
  597. [ 0.864388] audit: type=2000 audit(0.740:1): state=initialized audit_enabled=0 res=1
  598. [ 0.864730] workingset: timestamp_bits=62 max_order=19 bucket_order=0
  599. [ 1.051949] alg: No test for fips(ansi_cprng) (fips_ansi_cprng)
  600. [ 1.061374] async_tx: api initialized (async)
  601. [ 1.065808] alloc_chrdev_region: 246:0 bsg
  602. [ 1.070118] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
  603. [ 1.077582] io scheduler noop registered
  604. [ 1.081553] io scheduler cfq registered (default)
  605. [ 1.086298] io scheduler mq-deadline registered
  606. [ 1.090866] io scheduler kyber registered
  607. [ 1.097205] OF: PCI: host bridge /soc/pcie@3400000 ranges:
  608. [ 1.102804] OF: PCI: IO 0x4000010000..0x400001ffff -> 0x00000000
  609. [ 1.109131] OF: PCI: MEM 0x4040000000..0x407fffffff -> 0x40000000
  610. [ 1.115623] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0000:00
  611. [ 1.122388] pci_bus 0000:00: root bus resource [bus 00-ff]
  612. [ 1.127923] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
  613. [ 1.134154] pci_bus 0000:00: root bus resource [mem 0x4040000000-0x407fffffff] (bus address [0x40000000-0x7fffffff])
  614. [ 1.144777] pci 0000:00:00.0: [1957:8088] type 01 class 0x060400
  615. [ 1.150855] pci 0000:00:00.0: reg 0x38: [mem 0x4040000000-0x40400007ff pref]
  616. [ 1.157993] pci 0000:00:00.0: supports D1 D2
  617. [ 1.162298] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
  618. [ 1.168583] pci 0000:00:00.0: BAR 6: assigned [mem 0x4040000000-0x40400007ff pref]
  619. [ 1.176217] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
  620. [ 1.181676] pcieport 0000:00:00.0: Signaling PME with IRQ 70
  621. [ 1.187482] pcieport 0000:00:00.0: AER enabled with IRQ 71
  622. [ 1.193162] OF: PCI: host bridge /soc/pcie@3500000 ranges:
  623. [ 1.198701] OF: PCI: IO 0x4800010000..0x480001ffff -> 0x00000000
  624. [ 1.205024] OF: PCI: MEM 0x4840000000..0x487fffffff -> 0x40000000
  625. [ 1.211458] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0001:00
  626. [ 1.218220] pci_bus 0001:00: root bus resource [bus 00-ff]
  627. [ 1.223752] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff])
  628. [ 1.232784] pci_bus 0001:00: root bus resource [mem 0x4840000000-0x487fffffff] (bus address [0x40000000-0x7fffffff])
  629. [ 1.243398] pci 0001:00:00.0: [1957:8088] type 01 class 0x060400
  630. [ 1.249471] pci 0001:00:00.0: reg 0x38: [mem 0x4840000000-0x48400007ff pref]
  631. [ 1.256598] pci 0001:00:00.0: supports D1 D2
  632. [ 1.260905] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot
  633. [ 1.267166] pci 0001:00:00.0: BAR 6: assigned [mem 0x4840000000-0x48400007ff pref]
  634. [ 1.274802] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
  635. [ 1.280229] pcieport 0001:00:00.0: Signaling PME with IRQ 72
  636. [ 1.286032] pcieport 0001:00:00.0: AER enabled with IRQ 73
  637. [ 1.293511] Freescale LS2 console driver
  638. [ 1.297477] misc_register: 10, 62 fsl_mc_console
  639. [ 1.302265] fsl-ls2-console: device fsl_mc_console registered
  640. [ 1.308058] misc_register: 10, 61 fsl_aiop_console
  641. [ 1.313013] fsl-ls2-console: device fsl_aiop_console registered
  642. [ 1.320981] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
  643. [ 1.328515] console [ttyS0] disabled
  644. [ 1.332155] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 39, base_baud = 18750000) is a 16550A
  645. [ 1.341034] console [ttyS0] enabled
  646. [ 1.341034] console [ttyS0] enabled
  647. [ 1.348039] bootconsole [uart8250] disabled
  648. [ 1.348039] bootconsole [uart8250] disabled
  649. [ 1.356700] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 39, base_baud = 18750000) is a 16550A
  650. [ 1.365754] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 40, base_baud = 18750000) is a 16550A
  651. [ 1.374802] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 40, base_baud = 18750000) is a 16550A
  652. [ 1.384082] alloc_chrdev_region: 245:0 ttyLP
  653. [ 1.388753] misc_register: 10, 183 hw_random
  654. [ 1.398277] brd: module loaded
  655. [ 1.401347] misc_register: 10, 237 loop-control
  656. [ 1.409774] loop: module loaded
  657. [ 1.441748] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode
  658. [ 1.450734] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst
  659. [ 1.461111] scsi host0: ahci-qoriq
  660. [ 1.464662] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 52
  661. [ 1.473692] fsl-quadspi 1550000.quadspi: mx25u3235f (4096 Kbytes)
  662. [ 1.479872] 11 ofpart partitions found on MTD device 1550000.quadspi
  663. [ 1.486242] Creating 11 MTD partitions on "1550000.quadspi":
  664. [ 1.491915] 0x000000000000-0x000000200000 : "NOR (RO) RCW + E-Hole + U-boot Image"
  665. [ 1.499951] 0x000000200000-0x000000210000 : "NOR (RW) U-Boot ENV"
  666. [ 1.506475] 0x000000210000-0x000000220000 : "NOR (RO) EMPTY Hole 1"
  667. [ 1.513161] 0x000000220000-0x000000240000 : "NOR (RW) FMAN UCODE"
  668. [ 1.519701] 0x000000240000-0x000000280000 : "NOR (RW) E-HOLE 2 or PPA"
  669. [ 1.526636] 0x000000280000-0x0000002a0000 : "NOR (RW) WG CFG0"
  670. [ 1.532883] 0x0000002a0000-0x0000002c0000 : "NOR (RW) WG CFG1"
  671. [ 1.539137] 0x0000002c0000-0x0000002e0000 : "NOR (RW) WG MFG"
  672. [ 1.545312] 0x0000002e0000-0x000000300000 : "NOR (RW) E-HOLE 3"
  673. [ 1.551660] 0x000000300000-0x000000320000 : "NOR (RW) FMAN UCODE Old"
  674. [ 1.558531] 0x000000320000-0x000000400000 : "NOR (RW) WG bootOpt Data & reserved"
  675. [ 1.567520] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff
  676. [ 1.574731] libphy: Fixed MDIO Bus: probed
  677. [ 1.579900] libphy: Freescale XGMAC MDIO Bus: probed
  678. [ 1.586306] libphy: Freescale XGMAC MDIO Bus: probed
  679. [ 1.591841] libphy: Freescale XGMAC MDIO Bus: probed
  680. [ 1.597119] libphy: Freescale XGMAC MDIO Bus: probed
  681. [ 1.602412] libphy: Freescale XGMAC MDIO Bus: probed
  682. [ 1.607698] libphy: Freescale XGMAC MDIO Bus: probed
  683. [ 1.612970] libphy: Freescale XGMAC MDIO Bus: probed
  684. [ 1.618247] libphy: Freescale XGMAC MDIO Bus: probed
  685. [ 1.623517] libphy: Freescale XGMAC MDIO Bus: probed
  686. [ 1.644196] Freescale FM module, FMD API version 21.1.0
  687. [ 1.652780] Freescale FM Ports module
  688. [ 1.656456] fsl_mac: fsl_mac: FSL FMan MAC API based driver
  689. [ 1.662353] fman_memac_init: IF_MODE 2
  690. [ 1.666629] fsl_mac 1ae0000.ethernet: FMan MEMAC
  691. [ 1.671261] fsl_mac 1ae0000.ethernet: FMan MAC address: 00:0b:6b:01:01:01
  692. [ 1.678216] fman_memac_init: IF_MODE 2
  693. [ 1.682483] fsl_mac 1ae2000.ethernet: FMan MEMAC
  694. [ 1.687116] fsl_mac 1ae2000.ethernet: FMan MAC address: 00:0b:6b:01:01:02
  695. [ 1.694073] fman_memac_init: IF_MODE 8006
  696. [ 1.698099] fsl_mac 1ae4000.ethernet: FMan MEMAC
  697. [ 1.702729] fsl_mac 1ae4000.ethernet: FMan MAC address: 00:0b:6b:01:01:03
  698. [ 1.709696] fman_memac_init: IF_MODE 2
  699. [ 1.713964] fsl_mac 1ae8000.ethernet: FMan MEMAC
  700. [ 1.718595] fsl_mac 1ae8000.ethernet: FMan MAC address: 00:0b:6b:01:01:05
  701. [ 1.725559] fman_memac_init: IF_MODE 2
  702. [ 1.729830] fsl_mac 1aea000.ethernet: FMan MEMAC
  703. [ 1.734459] fsl_mac 1aea000.ethernet: FMan MAC address: 00:0b:6b:01:01:06
  704. [ 1.741326] fsl_dpa: FSL DPAA Ethernet driver
  705. [ 1.746657] fsl_dpa soc:fsl,dpaa:ethernet@0: Skip RX PCD High Priority FQs initialization
  706. [ 1.758936] fsl_dpa: fsl_dpa: Probed interface eth0
  707. [ 1.765223] fsl_dpa soc:fsl,dpaa:ethernet@1: Skip RX PCD High Priority FQs initialization
  708. [ 1.777829] fsl_dpa: fsl_dpa: Probed interface eth1
  709. [ 1.784791] fsl_dpa soc:fsl,dpaa:ethernet@2: Skip RX PCD High Priority FQs initialization
  710. [ 1.788450] ata1: SATA link down (SStatus 0 SControl 300)
  711. [ 1.803313] fsl_dpa: fsl_dpa: Probed interface eth2
  712. [ 1.808901] fsl_dpa soc:fsl,dpaa:ethernet@3: of_find_device_by_node(/soc/fman@1a00000/ethernet@e6000) failed
  713. [ 1.818771] fsl_dpa: probe of soc:fsl,dpaa:ethernet@3 failed with error -22
  714. [ 1.826961] fsl_dpa soc:fsl,dpaa:ethernet@4: Skip RX PCD High Priority FQs initialization
  715. [ 1.840794] fsl_dpa: fsl_dpa: Probed interface eth3
  716. [ 1.847282] fsl_dpa soc:fsl,dpaa:ethernet@5: Skip RX PCD High Priority FQs initialization
  717. [ 1.861138] fsl_dpa: fsl_dpa: Probed interface eth4
  718. [ 1.867107] fsl_dpa soc:fsl,dpaa:ethernet@8: of_find_device_by_node(/soc/fman@1a00000/ethernet@f0000) failed
  719. [ 1.876979] fsl_dpa: probe of soc:fsl,dpaa:ethernet@8 failed with error -22
  720. [ 1.883993] fsl_advanced: FSL DPAA Advanced drivers:
  721. [ 1.889621] fsl_proxy: FSL DPAA Proxy initialization driver
  722. [ 1.895483] fsl_oh: FSL FMan Offline Parsing port driver
  723. [ 1.903434] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  724. [ 1.909981] ehci-pci: EHCI PCI platform driver
  725. [ 1.914515] ehci-platform: EHCI generic platform driver
  726. [ 1.919977] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  727. [ 1.926174] ohci-pci: OHCI PCI platform driver
  728. [ 1.930660] ohci-platform: OHCI generic platform driver
  729. [ 1.936598] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  730. [ 1.942114] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
  731. [ 1.950263] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x22010810
  732. [ 1.959014] xhci-hcd xhci-hcd.0.auto: irq 49, io mem 0x02f00000
  733. [ 1.965304] hub 1-0:1.0: USB hub found
  734. [ 1.969083] hub 1-0:1.0: 1 port detected
  735. [ 1.973237] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  736. [ 1.978745] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
  737. [ 1.986420] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
  738. [ 1.993378] hub 2-0:1.0: USB hub found
  739. [ 1.997150] hub 2-0:1.0: 1 port detected
  740. [ 2.001376] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
  741. [ 2.006884] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
  742. [ 2.014937] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x22010810
  743. [ 2.023676] xhci-hcd xhci-hcd.1.auto: irq 50, io mem 0x03000000
  744. [ 2.029913] hub 3-0:1.0: USB hub found
  745. [ 2.033686] hub 3-0:1.0: 1 port detected
  746. [ 2.037831] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
  747. [ 2.043336] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
  748. [ 2.051019] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
  749. [ 2.057968] hub 4-0:1.0: USB hub found
  750. [ 2.061744] hub 4-0:1.0: 1 port detected
  751. [ 2.065959] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
  752. [ 2.071470] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 5
  753. [ 2.079619] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x22010810
  754. [ 2.088356] xhci-hcd xhci-hcd.2.auto: irq 51, io mem 0x03100000
  755. [ 2.094588] hub 5-0:1.0: USB hub found
  756. [ 2.098361] hub 5-0:1.0: 1 port detected
  757. [ 2.102498] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
  758. [ 2.108058] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 6
  759. [ 2.115737] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
  760. [ 2.122682] hub 6-0:1.0: USB hub found
  761. [ 2.126459] hub 6-0:1.0: 1 port detected
  762. [ 2.130759] usbcore: registered new interface driver usbserial
  763. [ 2.136637] usbcore: registered new interface driver usbserial_generic
  764. [ 2.143243] usbserial: USB Serial support registered for generic
  765. [ 2.149294] usbcore: registered new interface driver pl2303
  766. [ 2.154898] usbserial: USB Serial support registered for pl2303
  767. [ 2.170391] rtc-s35390a 0-0030: rtc core: registered rtc-s35390a as rtc0
  768. [ 2.177168] i2c /dev entries driver
  769. [ 2.180984] ptp_qoriq: device tree node missing required elements, try automatic configuration
  770. [ 2.189867] pps pps0: new PPS source ptp0
  771. [ 2.195173] misc_register: 10, 130 watchdog
  772. [ 2.199474] imx2-wdt 2ad0000.wdog: timeout 60 sec (nowayout=0)
  773. [ 2.205487] CPUidle arm: CPU 0 failed to init idle CPU ops
  774. [ 2.211282] sdhci: Secure Digital Host Controller Interface driver
  775. [ 2.217477] sdhci: Copyright(c) Pierre Ossman
  776. [ 2.221943] sdhci-pltfm: SDHCI platform and OF driver helper
  777. [ 2.271569] mmc0: SDHCI controller on 1560000.esdhc [1560000.esdhc] using ADMA 64-bit
  778. [ 2.283419] ledtrig-cpu: registered to indicate activity on CPUs
  779. [ 2.291040] platform caam_qi: Linux CAAM Queue I/F driver initialised
  780. [ 2.297602] caam-dma caam-dma: Defer probing after JR driver probing
  781. [ 2.304042] caam 1700000.crypto: Entropy delay = 3200
  782. [ 2.309160] caam 1700000.crypto: Instantiated RNG4 SH0
  783. [ 2.335896] caam 1700000.crypto: Instantiated RNG4 SH1
  784. [ 2.341069] caam 1700000.crypto: device ID = 0x0a12060000000000 (Era 8)
  785. [ 2.347729] caam 1700000.crypto: job rings = 3, qi = 1
  786. [ 2.354400] usbcore: registered new interface driver usbhid
  787. [ 2.359987] usbhid: USB HID core driver
  788. [ 2.364835] Freescale USDPAA process driver
  789. [ 2.368627] mmc0: new high speed MMC card at address 0001
  790. [ 2.371569] mmcblk0: mmc0:0001 M62704 3.56 GiB
  791. [ 2.371661] mmcblk0boot0: mmc0:0001 M62704 partition 1 2.00 MiB
  792. [ 2.371805] mmcblk0boot1: mmc0:0001 M62704 partition 2 2.00 MiB
  793. [ 2.371898] mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB
  794. [ 2.373850] mmcblk0: p1 p2 p3 p4 < p5 p6 p7 >
  795. [ 2.401030] fsl-usdpaa: no region found
  796. [ 2.404930] Freescale USDPAA process IRQ driver
  797. [ 2.409475] misc_register: 10, 60 fsl-usdpaa-irq
  798. [ 2.414707] Initializing XFRM netlink socket
  799. [ 2.419072] NET: Registered protocol family 10
  800. [ 2.424364] Segment Routing with IPv6
  801. [ 2.428086] ip6_tables: (C) 2000-2006 Netfilter Core Team
  802. [ 2.433499] NET: Registered protocol family 17
  803. [ 2.437962] NET: Registered protocol family 15
  804. [ 2.442425] Key type ceph registered
  805. [ 2.446086] libceph: loaded (mon/osd proto 15/24)
  806. [ 2.450926] misc_register: 10, 59 cpu_dma_latency
  807. [ 2.455782] misc_register: 10, 58 network_latency
  808. [ 2.460632] misc_register: 10, 57 network_throughput
  809. [ 2.465753] misc_register: 10, 56 memory_bandwidth
  810. [ 2.470703] registered taskstats version 1
  811. [ 2.475698] caam-dma caam-dma: caam dma support with 3 job rings
  812. [ 2.483150] rtc-s35390a 0-0030: setting system clock to 2022-04-25 10:05:58 UTC (1650881158)
  813. [ 2.494260] Freeing unused kernel memory: 5376K
  814. [ 3.084465] random: crng init done
  815. [ 5.027072] EXT4-fs (mmcblk0p5): mounting ext3 file system using the ext4 subsystem
  816. [ 5.035397] EXT4-fs (mmcblk0p5): INFO: recovery required on readonly filesystem
  817. [ 5.042722] EXT4-fs (mmcblk0p5): write access will be enabled during recovery
  818. [ 5.410427] EXT4-fs (mmcblk0p5): recovery complete
  819. [ 5.416399] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts:
  820. initrd: Integrity check bypassed
  821. [ 7.048396] Running /etc/runlevel/1/S02rootrw...Done.
  822. [ 7.050682] Running /etc/runlevel/1/S05mproc...Done.
  823. [ 7.051480] Running /etc/runlevel/1/S05sysfs...Done.
  824. [ 7.052223] Running /etc/runlevel/1/S06fixdev...Done.
  825. [ 7.053352] Running /etc/runlevel/1/S06temp...Done.
  826. [ 7.054024] Running /etc/runlevel/1/S10armled...Done.
  827. [ 7.064527] Running /etc/runlevel/1/S10diskpt...Done.
  828. [ 7.066763] Running /etc/runlevel/1/S18seed-random...Reseeded random generator
  829. [ 7.069300] Done.
  830. [ 7.081801] Running /etc/runlevel/2/S10var...Done.
  831. [ 7.084428] Running /etc/runlevel/2/S11shm...Done.
  832. [ 7.085629] Running /etc/runlevel/2/S13devpts...Done.
  833. [ 7.086212] Running /etc/runlevel/2/S15hosts...Done.
  834. [ 7.087221] Running /etc/runlevel/2/S16pending...mke2fs 1.44.1 (24-Mar-2018)
  835. [ 7.152268] Discarding device blocks: done
  836. [ 7.726127] Creating filesystem with 194560 4k blocks and 48672 inodes
  837. [ 7.726382] Filesystem UUID: 6e57ea48-c21a-4ef0-881a-f07103ff8574
  838. [ 7.726614] Superblock backups stored on blocks:
  839. [ 7.726793] 32768, 98304, 163840
  840. [ 7.726911]
  841. [ 7.726952] Allocating group tables: done
  842. [ 7.727241] Writing inode tables: done
  843. [ 7.751702] Writing superblocks and filesystem accounting information: done
  844. [ 8.466443]
  845. [ 8.469685] Done.
  846. [ 8.469758] Running /etc/runlevel/2/S18data...fsck 1.44.1 (24-Mar-2018)
  847. [ 8.490750] e2fsck 1.44.1 (24-Mar-2018)
  848. [ 8.497891] /dev/wgrd.sysa_data: clean, 479/48672 files, 9416/194560 blocks
  849. [ 7.723692] EXT4-fs (mmcblk0p5): mounting ext3 file system using the ext4 subsystem
  850. [ 7.740861] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
  851. [ 8.526511] Done.
  852. [ 8.526591] Running /etc/runlevel/2/S18data2...fsck 1.44.1 (24-Mar-2018)
  853. [ 8.532457] e2fsck 1.44.1 (24-Mar-2018)
  854. [ 8.535284] /dev/wgrd.data2 was not cleanly unmounted, check forced.
  855. [ 8.540258] Pass 1: Checking inodes, blocks, and sizes
  856. [ 9.129105] Pass 2: Checking directory structure
  857. [ 9.134894] Pass 3: Checking directory connectivity
  858. [ 9.135100] Pass 4: Checking reference counts
  859. [ 9.139965] Pass 5: Checking group summary information
  860. [ 9.157749] /dev/wgrd.data2: 12/48672 files (0.0% non-contiguous), 3257/194560 blocks
  861. [ 9.167170] Filesystem errors corrected.
  862. [ 9.167347] Done.
  863. [ 9.167407] Running /etc/runlevel/2/S18hotplug...Done.
  864. [ 9.177323] Running /etc/runlevel/2/S18kdump...kdump T20/T40
  865. [ 10.060715] Done.
  866. [ 10.060830] Running /etc/runlevel/2/S19caam...
  867. [ 9.308313] caam_jr 1710000.jr: registering rng-caam
  868. [ 9.472856] alg: No test for auth(sha1) (auth-sha1-caam)
  869. [ 9.478256] alg: No test for auth(sha256) (auth-sha256-caam)
  870. [ 9.483984] alg: No test for auth(sha384) (auth-sha384-caam)
  871. [ 9.489712] alg: No test for auth(sha512) (auth-sha512-caam)
  872. [ 9.728901] alg: No test for authenc(hmac(sha224),ecb(cipher_null)) (authenc-hmac-sha224-ecb-cipher_null-caam)
  873. [ 9.738991] alg: No test for authenc(hmac(sha256),ecb(cipher_null)) (authenc-hmac-sha256-ecb-cipher_null-caam)
  874. [ 9.749068] alg: No test for authenc(hmac(sha384),ecb(cipher_null)) (authenc-hmac-sha384-ecb-cipher_null-caam)
  875. [ 9.759148] alg: No test for authenc(hmac(sha512),ecb(cipher_null)) (authenc-hmac-sha512-ecb-cipher_null-caam)
  876. [ 9.769221] alg: No test for authenc(hmac(md5),cbc(aes)) (authenc-hmac-md5-cbc-aes-caam)
  877. [ 9.777389] alg: No test for echainiv(authenc(hmac(md5),cbc(aes))) (echainiv-authenc-hmac-md5-cbc-aes-caam)
  878. [ 9.796958] alg: No test for echainiv(authenc(hmac(sha1),cbc(aes))) (echainiv-authenc-hmac-sha1-cbc-aes-caam)
  879. [ 9.806955] alg: No test for authenc(hmac(sha224),cbc(aes)) (authenc-hmac-sha224-cbc-aes-caam)
  880. [ 9.815641] alg: No test for echainiv(authenc(hmac(sha224),cbc(aes))) (echainiv-authenc-hmac-sha224-cbc-aes-caam)
  881. [ 9.835731] alg: No test for echainiv(authenc(hmac(sha256),cbc(aes))) (echainiv-authenc-hmac-sha256-cbc-aes-caam)
  882. [ 9.846073] alg: No test for authenc(hmac(sha384),cbc(aes)) (authenc-hmac-sha384-cbc-aes-caam)
  883. [ 9.854758] alg: No test for echainiv(authenc(hmac(sha384),cbc(aes))) (echainiv-authenc-hmac-sha384-cbc-aes-caam)
  884. [ 9.874852] alg: No test for echainiv(authenc(hmac(sha512),cbc(aes))) (echainiv-authenc-hmac-sha512-cbc-aes-caam)
  885. [ 9.885193] alg: No test for authenc(hmac(md5),cbc(des3_ede)) (authenc-hmac-md5-cbc-des3_ede-caam)
  886. [ 9.894229] alg: No test for echainiv(authenc(hmac(md5),cbc(des3_ede))) (echainiv-authenc-hmac-md5-cbc-des3_ede-caam)
  887. [ 9.906387] alg: No test for echainiv(authenc(hmac(sha1),cbc(des3_ede))) (echainiv-authenc-hmac-sha1-cbc-des3_ede-caam)
  888. [ 9.918724] alg: No test for echainiv(authenc(hmac(sha224),cbc(des3_ede))) (echainiv-authenc-hmac-sha224-cbc-des3_ede-caam)
  889. [ 9.931405] alg: No test for echainiv(authenc(hmac(sha256),cbc(des3_ede))) (echainiv-authenc-hmac-sha256-cbc-des3_ede-caam)
  890. [ 9.944152] alg: No test for echainiv(authenc(hmac(sha384),cbc(des3_ede))) (echainiv-authenc-hmac-sha384-cbc-des3_ede-caam)
  891. [ 9.956843] alg: No test for echainiv(authenc(hmac(sha512),cbc(des3_ede))) (echainiv-authenc-hmac-sha512-cbc-des3_ede-caam)
  892. [ 9.968055] alg: No test for authenc(hmac(md5),cbc(des)) (authenc-hmac-md5-cbc-des-caam)
  893. [ 9.976221] alg: No test for echainiv(authenc(hmac(md5),cbc(des))) (echainiv-authenc-hmac-md5-cbc-des-caam)
  894. [ 9.987513] alg: No test for echainiv(authenc(hmac(sha1),cbc(des))) (echainiv-authenc-hmac-sha1-cbc-des-caam)
  895. [ 9.998984] alg: No test for echainiv(authenc(hmac(sha224),cbc(des))) (echainiv-authenc-hmac-sha224-cbc-des-caam)
  896. [ 10.010795] alg: No test for echainiv(authenc(hmac(sha256),cbc(des))) (echainiv-authenc-hmac-sha256-cbc-des-caam)
  897. [ 10.022614] alg: No test for echainiv(authenc(hmac(sha384),cbc(des))) (echainiv-authenc-hmac-sha384-cbc-des-caam)
  898. [ 10.034433] alg: No test for echainiv(authenc(hmac(sha512),cbc(des))) (echainiv-authenc-hmac-sha512-cbc-des-caam)
  899. [ 10.044776] alg: No test for authenc(hmac(md5),rfc3686(ctr(aes))) (authenc-hmac-md5-rfc3686-ctr-aes-caam)
  900. [ 10.054425] alg: No test for seqiv(authenc(hmac(md5),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-md5-rfc3686-ctr-aes-caam)
  901. [ 10.065258] alg: No test for seqiv(authenc(hmac(sha1),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha1-rfc3686-ctr-aes-caam)
  902. [ 10.076209] alg: No test for authenc(hmac(sha224),rfc3686(ctr(aes))) (authenc-hmac-sha224-rfc3686-ctr-aes-caam)
  903. [ 10.086377] alg: No test for seqiv(authenc(hmac(sha224),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha224-rfc3686-ctr-aes-caam)
  904. [ 10.097733] alg: No test for seqiv(authenc(hmac(sha256),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha256-rfc3686-ctr-aes-caam)
  905. [ 10.109089] alg: No test for seqiv(authenc(hmac(sha384),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha384-rfc3686-ctr-aes-caam)
  906. [ 10.120439] alg: No test for seqiv(authenc(hmac(sha512),rfc3686(ctr(aes)))) (seqiv-authenc-hmac-sha512-rfc3686-ctr-aes-caam)
  907. [ 10.131691] caam algorithms registered in /proc/crypto
  908. [ 10.203208] alg: No test for authenc(hmac(md5),cbc(aes)) (authenc-hmac-md5-cbc-aes-caam-qi)
  909. [ 10.211660] alg: No test for echainiv(authenc(hmac(md5),cbc(aes))) (echainiv-authenc-hmac-md5-cbc-aes-caam-qi)
  910. [ 10.224645] alg: No test for echainiv(authenc(hmac(sha1),cbc(aes))) (echainiv-authenc-hmac-sha1-cbc-aes-caam-qi)
  911. [ 10.234913] alg: No test for authenc(hmac(sha224),cbc(aes)) (authenc-hmac-sha224-cbc-aes-caam-qi)
  912. [ 10.243874] alg: No test for echainiv(authenc(hmac(sha224),cbc(aes))) (echainiv-authenc-hmac-sha224-cbc-aes-caam-qi)
  913. [ 10.257379] alg: No test for echainiv(authenc(hmac(sha256),cbc(aes))) (echainiv-authenc-hmac-sha256-cbc-aes-caam-qi)
  914. [ 10.267992] alg: No test for authenc(hmac(sha384),cbc(aes)) (authenc-hmac-sha384-cbc-aes-caam-qi)
  915. [ 10.276954] alg: No test for echainiv(authenc(hmac(sha384),cbc(aes))) (echainiv-authenc-hmac-sha384-cbc-aes-caam-qi)
  916. [ 10.290482] alg: No test for echainiv(authenc(hmac(sha512),cbc(aes))) (echainiv-authenc-hmac-sha512-cbc-aes-caam-qi)
  917. [ 10.301093] alg: No test for authenc(hmac(md5),cbc(des3_ede)) (authenc-hmac-md5-cbc-des3_ede-caam-qi)
  918. [ 10.310402] alg: No test for echainiv(authenc(hmac(md5),cbc(des3_ede))) (echainiv-authenc-hmac-md5-cbc-des3_ede-caam-qi)
  919. [ 10.321862] alg: No test for echainiv(authenc(hmac(sha1),cbc(des3_ede))) (echainiv-authenc-hmac-sha1-cbc-des3_ede-caam-qi)
  920. [ 10.333503] alg: No test for echainiv(authenc(hmac(sha224),cbc(des3_ede))) (echainiv-authenc-hmac-sha224-cbc-des3_ede-caam-qi)
  921. [ 10.345491] alg: No test for echainiv(authenc(hmac(sha256),cbc(des3_ede))) (echainiv-authenc-hmac-sha256-cbc-des3_ede-caam-qi)
  922. [ 10.357490] alg: No test for echainiv(authenc(hmac(sha384),cbc(des3_ede))) (echainiv-authenc-hmac-sha384-cbc-des3_ede-caam-qi)
  923. [ 10.369483] alg: No test for echainiv(authenc(hmac(sha512),cbc(des3_ede))) (echainiv-authenc-hmac-sha512-cbc-des3_ede-caam-qi)
  924. [ 10.380966] alg: No test for authenc(hmac(md5),cbc(des)) (authenc-hmac-md5-cbc-des-caam-qi)
  925. [ 10.389410] alg: No test for echainiv(authenc(hmac(md5),cbc(des))) (echainiv-authenc-hmac-md5-cbc-des-caam-qi)
  926. [ 10.400022] alg: No test for echainiv(authenc(hmac(sha1),cbc(des))) (echainiv-authenc-hmac-sha1-cbc-des-caam-qi)
  927. [ 10.410801] alg: No test for echainiv(authenc(hmac(sha224),cbc(des))) (echainiv-authenc-hmac-sha224-cbc-des-caam-qi)
  928. [ 10.421924] alg: No test for echainiv(authenc(hmac(sha256),cbc(des))) (echainiv-authenc-hmac-sha256-cbc-des-caam-qi)
  929. [ 10.433050] alg: No test for echainiv(authenc(hmac(sha384),cbc(des))) (echainiv-authenc-hmac-sha384-cbc-des-caam-qi)
  930. [ 10.444173] alg: No test for echainiv(authenc(hmac(sha512),cbc(des))) (echainiv-authenc-hmac-sha512-cbc-des-caam-qi)
  931. [ 10.456643] platform caam_qi: algorithms registered in /proc/crypto
  932. [ 10.529692] caam 1700000.crypto: caam pkc algorithms registered in /proc/crypto
  933. Done.
  934. [ 11.314703] Running /etc/runlevel/2/S19chkupgrade...Done.
  935. [ 11.328491] Running /etc/runlevel/2/S19csfc_post...
  936. [ 11.332630] CSfC Crypto self-test Bypassed
  937. [ 11.332804] Done.
  938. [ 11.332871] Running /etc/runlevel/2/S19ipv6...disabling IPv6 autoconf for all
  939. [ 11.334503] disabling IPv6 autoconf for default
  940. [ 11.334671] enable IPv6 forwarding for all
  941. [ 11.334821] enable IPv6 forwarding for default
  942. [ 11.334984] disabling IPv6 for all
  943. [ 11.335105] disabling IPv6 for default
  944. [ 11.335239] Done.
  945. [ 11.335299] Running /etc/runlevel/2/S19platform...Done.
  946. [ 11.336872] Running /etc/runlevel/2/S20adminhome...Done.
  947. [ 11.343466] Running /etc/runlevel/2/S20cleanup-dbg...Done.
  948. [ 11.349108] Running /etc/runlevel/2/S20cylanceconfig...Done.
  949. [ 11.591415] Running /etc/runlevel/2/S20gwc...Done.
  950. [ 11.592136] Running /etc/runlevel/2/S20sigs...unable to stat `/etc/defaults/signatures/dlp/PredefinedContentControlLists.xml' error No such file or directory
  951. [ 11.604347] unable to stat `/etc/defaults/signatures/dlp/dlp_list.xml.gz' error No such file or directory
  952. [ 11.604718] unable to stat `/etc/defaults/signatures/dlp/profile.xml' error No such file or directory
  953. [ 10.852939] usbcore: registered new interface driver usb-storage
  954. [ 11.614706] Done.
  955. [ 11.614771] Running /etc/runlevel/2/S20tweakthermals...S20tweakthermals: model T20
  956. [ 10.864457] wgipc: loading out-of-tree module taints kernel.
  957. [ 10.870635] wgipc: module license 'Watchguard Proprietary' taints kernel.
  958. [ 10.878751] Disabling lock debugging due to kernel taint
  959. [ 10.885771] genl_validate_assign_mc_groups first_id set to 20 for WGIPC mc group
  960. [ 11.619401] Setting Thermal Zone 0: trip_point_1_temp to 100C
  961. [ 11.619631] Setting Thermal Zone 1: trip_point_1_temp to 100C
  962. [ 11.619848] Setting Thermal Zone 2: trip_point_1_temp to 100C
  963. [ 10.906670] dpaa2_evb: module is from the staging directory, the quality is unknown, you have been warned.
  964. [ 11.620065] Setting Thermal Zone 3: trip_point_1_temp to 100C
  965. [ 10.922286] fsl_dpa soc:fsl,dpaa:ethernet@0 eth0.tmp: renamed from eth0
  966. [ 11.620298] Setting Thermal Zone 4: trip_point_1_temp to 100C
  967. [ 11.620516] Done.
  968. [ 10.939813] fsl_dpa soc:fsl,dpaa:ethernet@1 eth1.tmp: renamed from eth1
  969. [ 11.620575] Running /etc/runlevel/2/S20usb...Done.
  970. [ 11.637020] Running /etc/runlevel/2/S20wgbase...Done.
  971. [ 11.676207] Running /etc/runlevel/2/S21eth...
  972. [ 10.963788] fsl_dpa soc:fsl,dpaa:ethernet@2 eth0: renamed from eth2
  973. [ 10.979786] fsl_dpa soc:fsl,dpaa:ethernet@0 eth1: renamed from eth0.tmp
  974. [ 11.003776] fsl_dpa soc:fsl,dpaa:ethernet@1 eth2: renamed from eth1.tmp
  975. Done.
  976. [ 11.797180] Running /etc/runlevel/2/S21tpm_n_notpm...Done.
  977. [ 11.801555] Running /etc/runlevel/2/S22hwmon...Done.
  978. [ 11.804976] Running /etc/runlevel/2/S22login...Done.
  979. [ 11.805399] Running /etc/runlevel/2/S22rtc...Done.
  980. [ 11.811220] Running /etc/runlevel/2/S23pppoe...
  981. [ 11.050071] PPP generic driver version 2.4.2
  982. [ 11.065229] PPP MPPE Compression module registered
  983. [ 11.073973] PPP Deflate Compression module registered
  984. [ 11.082682] NET: Registered protocol family 24
  985. Done.
  986. [ 11.870510] Running /etc/runlevel/2/S23sslvpn...
  987. [ 11.101764] tun: Universal TUN/TAP device driver, 1.6
  988. [ 11.106913] misc_register: 10, 200 tun
  989. Done.
  990. [ 11.889231] Running /etc/runlevel/2/S23tpm...
  991. [ 11.243555] tpm tpm0: starting up the TPM manually
  992. S23tpm: Is a TPM DUT!
  993. [ 12.390833] Done.
  994. [ 12.390903] Running /etc/runlevel/2/S24fmcsetup...S24fmcsetup: model T20
  995. [ 12.716598] Done.
  996. [ 12.716672] Running /etc/runlevel/2/S24l2tpvpn...
  997. [ 11.953823] l2tp_core: L2TP core driver, V2.0
  998. [ 11.963303] l2tp_netlink: L2TP netlink interface
  999. [ 11.973928] l2tp_ppp: PPPoL2TP kernel driver, V2.0
  1000. Done.
  1001. [ 12.756584] Running /etc/runlevel/2/S24nginx...Done.
  1002. [ 12.759856] Running /etc/runlevel/2/S25core...Done.
  1003. [ 12.760988] Running /etc/runlevel/2/S25wgcfg...Info: No conversion required from version 12.7.2 to 12.7.2.
  1004. [ 13.167115] Done.
  1005. [ 13.167197] Running /etc/runlevel/2/S26defaultxml...Done.
  1006. [ 13.175807] Running /etc/runlevel/2/S27cfgcheck...Config ok
  1007. [ 14.261126] Done.
  1008. [ 14.261240] Running /etc/runlevel/2/S29wgcore...Done.
  1009. [ 14.276947] Running /etc/runlevel/2/S30backup...Done.
  1010. [ 14.278633] Running /etc/runlevel/2/S30net...
  1011. [ 13.520869] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
  1012. [ 13.539895] Bridge firewalling registered
  1013. [ 13.550847] Ebtables v2.0 registered
  1014. [ 13.710270] gre: GRE over IPv4 demultiplexor driver
  1015. [ 13.727207] ip_gre: GRE over IPv4 tunneling driver
  1016. [ 13.732570] register_netdevice: ifindex 7 -> iflink 0 gre0
  1017. [ 13.738805] register_netdevice: ifindex 8 -> iflink 0 gretap0
  1018. [ 13.745261] register_netdevice: ifindex 9 -> iflink 0 erspan0
  1019. [ 13.751224] bvpn vif handlers are registered
  1020. [ 13.762223] IPv4 over IPsec tunneling driver
  1021. [ 13.767008] register_netdevice: ifindex 10 -> iflink 0 ip_vti0
  1022. [ 13.785282] 8021q: 802.1Q VLAN Support v1.8
  1023. [ 13.807214] register_netdevice: ifindex 11 -> iflink 0 ip6tnl0
  1024. [ 13.820563] register_netdevice: ifindex 12 -> iflink 0 ip6_vti0
  1025. [ 13.848116] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
  1026. [ 13.854548] MII link monitoring set to 100 ms
  1027. Done.
  1028. [ 14.641946] Running /etc/runlevel/2/S30upgrade...Done.
  1029. [ 14.644232] Running /etc/runlevel/2/S30wireless...start load wireless modules
  1030. [ 14.647913] Done.
  1031. [ 14.647976] Running /etc/runlevel/2/S31cacert...Done.
  1032. [ 14.649671] Running /etc/runlevel/2/S31cert...Done.
  1033. [ 14.678591] Running /etc/runlevel/2/S31crypto...Done.
  1034. [ 14.690612] Running /etc/runlevel/2/S31xtables...[ 13.920023] Netfilter messages via NETLINK v0.30.
  1035. [ 14.048550] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
  1036. [ 14.054765] nf_conntrack_init_start: conntrack max=65536 high water mark=52428
  1037. [ 14.201885] ip_tables: (C) 2000-2006 Netfilter Core Team
  1038. [ 14.392327] nf_ct_ftp: Maximum expected value 1
  1039. [ 14.487369] ctnetlink v0.93: registering with nfnetlink.
  1040. [ 14.660955] arp_tables: arp_tables: (C) 2002 David S. Miller
  1041. [ 14.754534] u32 classifier
  1042. [ 14.757319] input device check on
  1043. [ 14.760997] Actions configured
  1044. [ 14.782680] Mirror/redirect action on
  1045. Done.
  1046. [ 15.568871] Running /etc/runlevel/2/S31xtables6...Done.
  1047. [ 15.896807] Running /etc/runlevel/2/S32auth...Done.
  1048. [ 15.905271] Running /etc/runlevel/2/S32clst...Done.
  1049. [ 15.933217] Running /etc/runlevel/2/S32modemdrivers...
  1050. [ 15.177363] usbcore: registered new interface driver option
  1051. [ 15.183120] usbserial: USB Serial support registered for GSM modem (1-port)
  1052. [ 15.196100] usbcore: registered new interface driver wg_sierra
  1053. [ 15.202034] usbserial: USB Serial support registered for Sierra USB modem
  1054. [ 15.215711] usbcore: registered new interface driver cdc_acm
  1055. [ 15.221411] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  1056. [ 15.234475] usbcore: registered new interface driver GobiSerial
  1057. [ 15.240503] usbserial: USB Serial support registered for GobiSerial
  1058. [ 15.246808] GobiSerial: 2013-10-08/NTGR_2.12:GobiSerial
  1059. [ 15.270734] usbcore: registered new interface driver cdc_ether
  1060. [ 15.282027] usbcore: registered new interface driver rndis_host
  1061. [ 15.293518] usbcore: registered new interface driver sierra_net
  1062. [ 15.309055] GobiNet: 2013-10-08/NTGR_2.21
  1063. [ 15.313293] usbcore: registered new interface driver GobiNet
  1064. [ 15.324704] usbcore: registered new interface driver cdc_wdm
  1065. [ 15.338751] usbcore: registered new interface driver qmi_wwan
  1066. [ 15.351448] usbcore: registered new interface driver cdc_ncm
  1067. [ 15.361138] usbcore: registered new interface driver huawei_cdc_ncm
  1068. Done.
  1069. [ 16.145276] Running /etc/runlevel/2/S32wgxt...
  1070. [ 15.409376] ipt_addrpairs_6 v0.1.0: Loading
  1071. [ 15.421229] xt_session6 : Loading
  1072. [ 15.424608] xt_session6 : Loaded limit 1000 hash 1024 WG IPC ID 184549376 (0x0B000000)
  1073. [ 15.476562] ipt_addrpairs: ADDRPAIRS SCALE Set MAX 16384 Entry Max 16384
  1074. [ 15.483321] ipt_addrpairs: v1.0.0 Loaded
  1075. [ 15.493672] xt_ifset: Loaded with set limit 5000 and entry limit 5000
  1076. [ 15.503850] xt_classify : Loaded
  1077. [ 15.510763] xt_master: Loaded
  1078. [ 15.517563] xt_MASTER: Loaded
  1079. [ 15.524355] xt_WGTEE: Loaded
  1080. [ 15.531434] Schedule: Loaded
  1081. [ 15.538259] xt_POLICY: Loaded
  1082. [ 15.544880] xt_policy : Loaded
  1083. [ 15.551780] xt_EXPIRES: Loaded
  1084. [ 15.558661] xt_IPPRECEDENCE: Loaded
  1085. [ 15.574116] xt_PKTCACHE: Loaded
  1086. [ 15.586784] xt_session : Loaded limit 1000 hash 1024 WG IPC ID 92274688 (0x05800000)
  1087. [ 15.610186] xt_CONNCLASSIFY: Loaded
  1088. [ 15.617431] xt_connclassify : Loaded
  1089. [ 15.626233] xt_ipspoof : Loaded
  1090. [ 15.714702] xt_LBDNAT: Loaded
  1091. [ 15.725155] xt_MWAN: Loaded
  1092. [ 15.736958] xt_psd: Loaded
  1093. [ 15.743958] xt_ipsd: Loaded
  1094. [ 15.751015] xt_ddos: Loaded
  1095. [ 15.758713] xt_dos: Loaded
  1096. [ 15.767965] xt_wgaccount: Allocated 117 policy counter block array
  1097. [ 15.774220] xt_wgaccount: Allocated policy counter block 0 of size 4080 at ffff8000704a1000
  1098. [ 15.782597] xt_wgaccount: Allocated policy counter block 1 of size 4080 at ffff800071f50000
  1099. [ 15.790977] xt_wgaccount: Loaded
  1100. [ 15.881976] xt_block : Loaded limit 1000 hash 1024 WG IPC ID 155189248
  1101. [ 15.896213] xt_localroute: Loaded
  1102. [ 15.907067] xt_duplicate: Loaded
  1103. [ 15.923923] xt_WGCLASSIFY: Loaded
  1104. [ 15.959116] xt_fqdn : Loading
  1105. [ 15.962336] xt_fqdn : Loaded
  1106. [ 15.975673] devsec : Loaded limit 1000 hash 1024 WGIPC ID 260046848 (0x0F800000)
  1107. [ 15.989303] xt_geo: Loaded limit 300 hash 256 WGIPC ID 272629760 (0x10400000)
  1108. [ 15.996549] xt_sdwan: Loaded
  1109. [ 16.010403] xt_WGCT: Loaded
  1110. Done.
  1111. [ 16.809189] Running /etc/runlevel/2/S33appID...
  1112. [ 16.089484] tdts: Passive init mode
  1113. [ 16.097765] WG workqueue: Loaded
  1114. [ 16.176697] DPI engine defaults: conn_max=4096 tcp_reasm=1 eva_enhance=1 ac_type=0
  1115. [ 16.184288] DPI engine active configuration: conn_max=500000 tcp_reasm=0 eva_enhance=0 ac_type=0
  1116. [ 16.198397] Init chrdev /dev/detector with major 190
  1117. [ 16.203417] DPI engine version 2.0.30 965e09
  1118. [ 16.207702] DPI engine initialization succeeded
  1119. [ 16.243543] Loaded
  1120. Done.
  1121. [ 17.023424] Running /etc/runlevel/2/S35nropen...updated /proc/sys/fs/nr_open with new value: 2097152
  1122. [ 16.255708] Proxy glue: Loaded 17:41:19 (248)
  1123. [ 17.024521] Done.
  1124. [ 17.024582] Running /etc/runlevel/2/S35proxy...Setting the proxy tmpfs size to size=457m.
  1125. [ 17.291963] /usr/bin/pxyhelper returned 0
  1126. [ 17.292119] Done.
  1127. [ 17.292179] Running /etc/runlevel/2/S35scand...Done.
  1128. [ 17.301707] Running /etc/runlevel/2/S36dynroute...Done.
  1129. [ 17.302192] Running /etc/runlevel/2/S42notpm_restore...systemdata file not provided, defaulting to (/etc/wg/tcsd/lib/tpm/system.data)
  1130. [ 17.323842] restoring
  1131. [ 17.323924] restore complete: systemdata_payload restore OK, length:2352
  1132. [ 17.324185] Dealing with tpm DUT
  1133. [ 17.324302] Done.
  1134. [ 17.324361] Running /etc/runlevel/2/S42ssh...Done.
  1135. [ 17.326493] Running /etc/runlevel/2/S44sysb...Done.
  1136. [ 17.344961] Running /etc/runlevel/2/S45clientless...Done.
  1137. [ 17.345576] Running /etc/runlevel/2/S45portald...Done.
  1138. [ 17.346995] Running /etc/runlevel/2/S50nettune...Setting IPv4 route garbage collection timeout to 2 minutes
  1139. [ 17.347971] Setting promote_secondaries to 1
  1140. [ 17.348129] Setting icmp_errors_use_inbound_ifaddr to 1
  1141. [ 17.348325] Done.
  1142. [ 17.348385] Running /etc/runlevel/2/S60daas...Done.
  1143. [ 17.349697] Running /etc/runlevel/2/S80seed-random...Saved random seed
  1144. [ 17.356407] Done.
  1145. [ 17.356470] Running /etc/runlevel/2/S90bootmon...Done.
  1146. [ 17.359683] Running /etc/runlevel/2/S90kcrashrep...Done.
  1147. [ 17.391665] Running /etc/runlevel/2/S98setmacs...setting device eth0 to 00:01:21:2a:cf:f9
  1148. [ 17.402787] setting device eth1 to 00:01:21:2a:cf:fa
  1149. [ 17.402988] setting device eth2 to 00:01:21:2a:cf:fb
  1150. [ 17.403174] setting device eth3 to 00:01:21:2a:cf:fc
  1151. [ 17.403366] setting device eth4 to 00:01:21:2a:cf:fd
  1152. [ 17.403565] Done.
  1153. [ 17.403625] Running /etc/runlevel/2/S99fetchmac0...Done.
  1154. [ 17.406930] Running /etc/runlevel/2/S99igmp...Done.
  1155. [ 17.407353] Running /etc/runlevel/2/S99rootro...Done.
  1156. [ 20.735461] wg_ctmax_proc_dointvec: conntrack max=52600 high water mark=42080
  1157. [ 22.164580] Running /etc/runlevel/4/S51armled...Done.
  1158. [ 22.192068] Running /etc/runlevel/4/S81ckwebupload...Done.
  1159. [ 22.213279] Running /etc/runlevel/4/S99defaultap...Not a wireless model, skipping script
  1160. [ 22.219929] Done.
  1161. ​
  1162. smolguard login:

Edit this Snippet