Snippet content copied to clipboard.
Are you sure to delete this snippet? No, don't delete
  1. TIM-1.0
  2. WTMI-armada-17.10.3-d61ed3a
  3. WTMI: system early-init
  4. ​
  5. DDR topology parameters:
  6. ========================
  7. ddr type DDR3
  8. ddr speedbin 12
  9. bus width 16-bits
  10. cs num 2
  11. cs[0] - group num 0
  12. cs[0] - bank num 8
  13. cs[0] - capacity 512MiB
  14. cs[1] - group num 0
  15. cs[1] - bank num 8
  16. cs[1] - capacity 512MiB
  17. ​
  18. DRAM windows:
  19. =============
  20. WIN[0] - base addr 0x60000000
  21. WIN[0] - size 0x40000000
  22. WIN[1] - base addr 0xa0000000
  23. WIN[1] - size 0x20000000
  24. ​
  25. memory test region:
  26. ===================
  27. CS[0] 0x60000000 - 0x7fffffff
  28. CS[1] 0x80000000 - 0x9fffffff
  29. ​
  30. Fill memory before self refresh...done
  31. ​
  32. Fill memory before self refresh...done
  33. ​
  34. Now in Self-refresh Mode
  35. Restore termination values to original values
  36. Exited self-refresh ...
  37. ​
  38. ​
  39. Self refresh Pass.
  40. DDR self test mode test done!!
  41. ​
  42. Self refresh Pass.
  43. DDR self test mode test done!!
  44. ​
  45. QS GATING
  46. =============
  47. Calibration done: cycle = 0x00 tap =0x5E
  48. CH0_PHY_RL_Control_CS0_B0[0xC0001180]: 0x0000005E
  49. CH0_PHY_RL_Control_CS0_B1[0xC0001184]: 0x0000005E
  50. ​
  51. ​
  52. QS GATING
  53. =============
  54. Calibration done: cycle = 0x00 tap =0x5D
  55. CH0_PHY_RL_Control_CS1_B0[0xC00011A4]: 0x0000005D
  56. CH0_PHY_RL_Control_CS1_B1[0xC00011A8]: 0x0000005D
  57. ​
  58. DLL TUNING
  59. ==============
  60. DLL 0xc0001050[21:16]: [0,2f,17]
  61. DLL 0xc0001050[29:24]: [4,34,1c]
  62. DLL 0xc0001054[21:16]: [0,2b,15]
  63. DLL 0xc0001054[29:24]: [a,36,20]
  64. DLL 0xc0001074[21:16]: [0,3f,1f]
  65. DLL 0xc0001074NOTICE: Booting Trusted Firmware
  66. NOTICE: BL1: v1.3(debug):armada-17.10.7:16571d2
  67. NOTICE: BL1: Built : 15:51:32, Apr 19 2NOTICE: BL2: v1.3(debug):armada-17.10.7:16571d2
  68. NOTICE: BL2: Built : 15:51:34, Apr 19 2018NOTICE: BL31: v1.3(debug):armada-17.10.7:16571d2
  69. NOTICE: BL31:
  70. ​
  71. U-Boot 2017.03-armada-17.10.1 (Dec 29 2018 - 11:26:46 +0800)
  72. ​
  73. Model: Marvell Armada 3720 ECK Board
  74. CPU @ 1000 [MHz]
  75. L2 @ 800 [MHz]
  76. TClock @ 200 [MHz]
  77. DDR @ 800 [MHz]
  78. DRAM: 1 GiB
  79. U-Boot DT blob at : 000000003f71b328
  80. Comphy-0: USB3 5 Gbps
  81. Comphy-1: PEX0 2.5 Gbps
  82. Comphy-2: SATA0 6 Gbps
  83. MMC: sdhci@d8000: 0
  84. SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB
  85. *** Warning - bad CRC, using default environment
  86. ​
  87. Net: SF: Detected gd25lq80 with page size 256 Bytes, erase size 4 KiB, total 1 MiB
  88. Factory mac is : B0-A7-B9-8E-EC-F1
  89. eth0: neta@30000 [PRIME]
  90. Attach switch ID 0x004dd043
  91. Attach switch driver for AR8236
  92. Checking for firmware recovery mode...
  93. Reset button not pushed, do nothing
  94. Press CTRL+B to abort autoboot in 1 seconds
  95. switch to partitions #0, OK
  96. mmc0(part 0) is current device
  97. ​
  98. MMC read: dev # 0, block # 896, count 128 ... 128 blocks read: OK
  99. switch to partitions #0, OK
  100. mmc0(part 0) is current device
  101. ​
  102. MMC read: dev # 0, block # 1024, count 32768 ... 32768 blocks read: OK
  103. ## Flattened Device Tree blob at 04f00000
  104. Booting using the fdt blob at 0x4f00000
  105. Using Device Tree in place at 0000000004f00000, end 0000000004f05d72
  106. ​
  107. Starting kernel ...
  108. ​
  109. [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
  110. [ 0.000000] Linux version 5.10.109 (aholmes@astraea-lnx) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19375-77f278b3fbf) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Apr 7 09:12:29 2022
  111. [ 0.000000] Machine model: TP-Link Omada OC200
  112. [ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options '')
  113. [ 0.000000] printk: bootconsole [ar3700_uart0] enabled
  114. [ 0.000000] efi: UEFI not found.
  115. [ 0.000000] Zone ranges:
  116. [ 0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff]
  117. [ 0.000000] DMA32 empty
  118. [ 0.000000] Normal empty
  119. [ 0.000000] Movable zone start for each node
  120. [ 0.000000] Early memory node ranges
  121. [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
  122. [ 0.000000] node 0: [mem 0x0000000004000000-0x00000000041fffff]
  123. [ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff]
  124. [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
  125. [ 0.000000] psci: probing for conduit method from DT.
  126. [ 0.000000] psci: PSCIv1.0 detected in firmware.
  127. [ 0.000000] psci: Using standard PSCI v0.2 function IDs
  128. [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
  129. [ 0.000000] psci: SMC Calling Convention v1.0
  130. [ 0.000000] percpu: Embedded 16 pages/cpu s28248 r8192 d29096 u65536
  131. [ 0.000000] Detected VIPT I-cache on CPU0
  132. [ 0.000000] CPU features: detected: GIC system register CPU interface
  133. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
  134. [ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000 mtdparts=spi0.0:1M(nor-flash) root=/dev/mmcblk0p1 rw rootwait
  135. [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
  136. [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
  137. [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
  138. [ 0.000000] Memory: 1013808K/1048576K available (8384K kernel code, 954K rwdata, 2220K rodata, 512K init, 284K bss, 34768K reserved, 0K cma-reserved)
  139. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  140. [ 0.000000] rcu: Hierarchical RCU implementation.
  141. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
  142. [ 0.000000] Tracing variant of Tasks RCU enabled.
  143. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
  144. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
  145. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
  146. [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
  147. [ 0.000000] GICv3: 192 SPIs implemented
  148. [ 0.000000] GICv3: 0 Extended SPIs implemented
  149. [ 0.000000] GICv3: Distributor has no Range Selector support
  150. [ 0.000000] GICv3: 16 PPIs implemented
  151. [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
  152. [ 0.000000] random: get_random_bytes called from start_kernel+0x3a8/0x57c with crng_init=0
  153. [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
  154. [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
  155. [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
  156. [ 0.008365] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
  157. [ 0.018960] pid_max: default: 32768 minimum: 301
  158. [ 0.023812] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
  159. [ 0.031361] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
  160. [ 0.040694] rcu: Hierarchical SRCU implementation.
  161. [ 0.046048] EFI services will not be available.
  162. [ 0.050773] smp: Bringing up secondary CPUs ...
  163. [ 0.055776] Detected VIPT I-cache on CPU1
  164. [ 0.055810] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000
  165. [ 0.055854] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
  166. [ 0.055946] smp: Brought up 1 node, 2 CPUs
  167. [ 0.078004] SMP: Total of 2 processors activated.
  168. [ 0.082839] CPU features: detected: 32-bit EL0 Support
  169. [ 0.088130] CPU features: detected: CRC32 instructions
  170. [ 0.093449] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
  171. [ 0.102019] CPU: All CPU(s) started at EL2
  172. [ 0.106232] alternatives: patching kernel code
  173. [ 0.113591] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  174. [ 0.123680] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
  175. [ 0.130756] pinctrl core: initialized pinctrl subsystem
  176. [ 0.136595] DMI not present or invalid.
  177. [ 0.140953] NET: Registered protocol family 16
  178. [ 0.145884] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
  179. [ 0.153131] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
  180. [ 0.161070] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
  181. [ 0.169571] thermal_sys: Registered thermal governor 'step_wise'
  182. [ 0.170062] cpuidle: using governor ladder
  183. [ 0.180557] ASID allocator initialised with 65536 entries
  184. [ 0.208220] cryptd: max_cpu_qlen set to 1000
  185. [ 0.214571] SCSI subsystem initialized
  186. [ 0.218823] usbcore: registered new interface driver usbfs
  187. [ 0.224500] usbcore: registered new interface driver hub
  188. [ 0.229962] usbcore: registered new device driver usb
  189. [ 0.237396] clocksource: Switched to clocksource arch_sys_counter
  190. [ 0.244299] NET: Registered protocol family 2
  191. [ 0.248922] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
  192. [ 0.257258] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
  193. [ 0.265834] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
  194. [ 0.273841] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
  195. [ 0.281324] TCP: Hash tables configured (established 8192 bind 8192)
  196. [ 0.287941] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
  197. [ 0.294698] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
  198. [ 0.302102] NET: Registered protocol family 1
  199. [ 0.306525] PCI: CLS 0 bytes, default 64
  200. [ 0.311928] workingset: timestamp_bits=46 max_order=18 bucket_order=0
  201. [ 0.322057] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  202. [ 0.328036] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  203. [ 0.344279] mv_xor d0060900.xor: Marvell shared XOR driver
  204. [ 0.428057] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
  205. [ 0.518053] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
  206. [ 0.525740] debugfs: Directory 'd0060900.xor' with parent 'dmaengine' already present!
  207. [ 0.534026] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
  208. [ 0.541977] cacheinfo: Unable to detect cache hierarchy for CPU 0
  209. [ 0.551988] loop: module loaded
  210. [ 0.557909] spi-nor spi0.0: gd25lq80c (1024 Kbytes)
  211. [ 0.563080] 1 fixed-partitions partitions found on MTD device spi0.0
  212. [ 0.569698] Creating 1 MTD partitions on "spi0.0":
  213. [ 0.574548] 0x000000000000-0x000000100000 : "nor"
  214. [ 0.586555] mvneta: register 0x243c original value: 0
  215. [ 0.591721] mvneta: register 0x243c modified value: 70000000
  216. [ 0.598344] mvneta d0030000.ethernet eth0: Using random mac address 4a:ac:35:dd:23:db
  217. [ 0.606598] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  218. [ 0.613290] ehci-pci: EHCI PCI platform driver
  219. [ 0.617890] ehci-platform: EHCI generic platform driver
  220. [ 0.623347] ehci-orion: EHCI orion driver
  221. [ 0.627714] orion-ehci d005e000.usb: EHCI Host Controller
  222. [ 0.633212] orion-ehci d005e000.usb: new USB bus registered, assigned bus number 1
  223. [ 0.641125] orion-ehci d005e000.usb: irq 23, io mem 0xd005e000
  224. [ 0.677432] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00
  225. [ 0.683947] hub 1-0:1.0: USB hub found
  226. [ 0.687786] hub 1-0:1.0: 1 port detected
  227. [ 0.692843] usbcore: registered new interface driver usb-storage
  228. [ 0.699173] i2c /dev entries driver
  229. [ 0.703459] armada_37xx_wdt d0008300.watchdog: Initial timeout 120 sec
  230. [ 0.710648] sdhci: Secure Digital Host Controller Interface driver
  231. [ 0.716941] sdhci: Copyright(c) Pierre Ossman
  232. [ 0.721593] sdhci-pltfm: SDHCI platform and OF driver helper
  233. [ 0.727547] leds-gpio leds: there is not valid maps for state default
  234. [ 0.735939] NET: Registered protocol family 10
  235. [ 0.741500] Segment Routing with IPv6
  236. [ 0.745246] NET: Registered protocol family 17
  237. [ 0.749832] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
  238. [ 0.753655] mmc0: SDHCI controller on d00d8000.sdhci [d00d8000.sdhci] using ADMA
  239. [ 0.763325] 8021q: 802.1Q VLAN Support v1.8
  240. [ 0.778831] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 0, base_baud = 1562500) is a mvebu-uart
  241. [ 0.788309] printk: console [ttyMV0] enabled
  242. [ 0.788309] printk: console [ttyMV0] enabled
  243. [ 0.797041] printk: bootconsole [ar3700_uart0] disabled
  244. [ 0.797041] printk: bootconsole [ar3700_uart0] disabled
  245. [ 0.834913] mmc0: new HS400 MMC card at address 0001
  246. [ 0.840851] mmcblk0: mmc0:0001 4FTE4R 3.64 GiB
  247. [ 0.845818] mmcblk0boot0: mmc0:0001 4FTE4R partition 1 4.00 MiB
  248. [ 0.852252] mmcblk0boot1: mmc0:0001 4FTE4R partition 2 4.00 MiB
  249. [ 0.858486] mmcblk0rpmb: mmc0:0001 4FTE4R partition 3 512 KiB, chardev (249:0)
  250. [ 0.866689] mmcblk0: p1 p2 p3 p4
  251. [ 0.870342] mmcblk0: p4 size 7200768 extends beyond EOD, truncated
  252. [ 2.814561] qca8k d0032004.mdio-mii:10: mib init failed
  253. [ 4.856530] qca8k d0032004.mdio-mii:10: configuring for fixed/rgmii link mode
  254. [ 4.867335] qca8k d0032004.mdio-mii:10: Link is Up - 100Mbps/Full - flow control off
  255. [ 4.875421] qca8k d0032004.mdio-mii:10 lan0 (uninitialized): PHY [d0032004.mdio-mii:00] driver [Generic PHY] (irq=POLL)
  256. [ 4.887722] qca8k d0032004.mdio-mii:10 lan1 (uninitialized): PHY [d0032004.mdio-mii:01] driver [Generic PHY] (irq=POLL)
  257. [ 4.916693] DSA: tree 0 setup
  258. [ 4.927007] xhci-hcd d0058000.usb: xHCI Host Controller
  259. [ 4.932445] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 2
  260. [ 4.940204] xhci-hcd d0058000.usb: hcc params 0x0a000998 hci version 0x100 quirks 0x0000000000010090
  261. [ 4.949678] xhci-hcd d0058000.usb: irq 22, io mem 0xd0058000
  262. [ 4.956110] hub 2-0:1.0: USB hub found
  263. [ 4.960039] hub 2-0:1.0: 1 port detected
  264. [ 4.964326] xhci-hcd d0058000.usb: xHCI Host Controller
  265. [ 4.969766] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 3
  266. [ 4.977418] xhci-hcd d0058000.usb: Host supports USB 3.0 SuperSpeed
  267. [ 4.983948] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
  268. [ 4.992718] hub 3-0:1.0: USB hub found
  269. [ 4.996621] hub 3-0:1.0: 1 port detected
  270. [ 5.001445] armada-37xx-rwtm-mailbox d00b0000.mailbox: Secure processor not ready
  271. [ 5.009212] turris-mox-rwtm firmware:armada-3700-rwtm: Cannot read board information: -5
  272. [ 5.017579] armada-37xx-rwtm-mailbox d00b0000.mailbox: Secure processor not ready
  273. [ 5.025389] turris-mox-rwtm firmware:armada-3700-rwtm: Firmware does not support the GET_RANDOM command
  274. [ 5.035153] turris-mox-rwtm: probe of firmware:armada-3700-rwtm failed with error -5
  275. [ 5.055684] VFS: Mounted root (squashfs filesystem) readonly on device 179:1.
  276. [ 5.064215] Freeing unused kernel memory: 512K
  277. [ 5.107526] Run /sbin/init as init process
  278. [ 5.311369] init: Console is alive
  279. [ 5.315050] init: - watchdog -
  280. [ 5.503802] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  281. [ 5.524362] ehci-fsl: Freescale EHCI Host controller driver
  282. [ 5.533777] usbcore: registered new interface driver uas
  283. [ 5.539602] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  284. [ 5.551244] init: - preinit -
  285. [ 5.758852] random: fast init done
  286. [ 5.922979] random: jshn: uninitialized urandom read (4 bytes read)
  287. [ 5.946263] random: jshn: uninitialized urandom read (4 bytes read)
  288. [ 5.971634] random: jshn: uninitialized urandom read (4 bytes read)
  289. [ 6.247328] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii link mode
  290. [ 6.256062] mvneta d0030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
  291. [ 6.266061] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  292. Press the [f] key and hit [enter] to enter failsafe mode
  293. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  294. [ 10.548523] urandom_read: 2 callbacks suppressed
  295. [ 10.548532] random: procd: uninitialized urandom read (4 bytes read)
  296. [ 10.611644] F2FS-fs (loop0): Mounted with checkpoint version = d70cadc
  297. [ 10.619228] mount_root: switching to f2fs overlay
  298. [ 10.625225] overlayfs: "xino" feature enabled using 32 upper inode bits.
  299. [ 10.661570] mmcblk0p1: Can't mount, would change RO state
  300. [ 10.669315] /dev/mmcblk0p1: Can't open blockdev
  301. mount: mounting /dev/mmcblk0p1 on /boot failed: Resource busy
  302. umount: can't unmount /boot: Invalid argument
  303. [ 10.745031] urandom-seed: Seeding 4096 bits and crediting
  304. [ 10.750762] random: crng init done
  305. [ 10.756197] urandom-seed: Saving 4096 bits of creditable seed for next boot
  306. [ 10.789532] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
  307. [ 11.810900] mvneta d0030000.ethernet eth0: TIMEOUT for TX stopped status=0x0000ff5d
  308. [ 21.821224] mvneta d0030000.ethernet eth0: TX FIFO empty timeout status=0x00010001
  309. [ 21.829243] mvneta d0030000.ethernet eth0: Link is Down
  310. [ 21.852543] procd: - early -
  311. [ 21.855630] procd: - watchdog -
  312. Failed to connect to ubus
  313. [ 22.389339] procd: - watchdog -
  314. [ 22.394658] procd: - ubus -
  315. [ 22.555163] procd: - init -
  316. Please press Enter to activate this console.
  317. [ 22.867480] urngd: v1.0.2 started.
  318. [ 22.909996] kmodloader: loading kernel modules from /etc/modules.d/*
  319. [ 22.928980] zram: Added device: zram0
  320. [ 22.957108] usbcore: registered new interface driver usbserial_generic
  321. [ 22.963985] usbserial: USB Serial support registered for generic
  322. [ 22.971165] usbcore: registered new interface driver ch341
  323. [ 22.976910] usbserial: USB Serial support registered for ch341-uart
  324. [ 22.984494] usbcore: registered new interface driver cp210x
  325. [ 22.990400] usbserial: USB Serial support registered for cp210x
  326. [ 22.998164] usbcore: registered new interface driver ftdi_sio
  327. [ 23.004191] usbserial: USB Serial support registered for FTDI USB Serial Device
  328. [ 23.040996] kmodloader: done loading kernel modules from /etc/modules.d/*
  329. [ 26.446941] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii link mode
  330. [ 26.454932] mvneta d0030000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
  331. [ 26.467912] br-lan: port 1(eth0) entered blocking state
  332. [ 26.473320] br-lan: port 1(eth0) entered disabled state
  333. [ 26.479009] device eth0 entered promiscuous mode
  334. [ 26.485937] br-lan: port 1(eth0) entered blocking state
  335. [ 26.491399] br-lan: port 1(eth0) entered forwarding state
  336. [ 27.467500] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  337. ​
  338. ​
  339. ​
  340. BusyBox v1.35.0 (2022-04-07 09:12:29 UTC) built-in shell (ash)
  341. ​
  342. _______ ________ __
  343. | |.-----.-----.-----.| | | |.----.| |_
  344. | - || _ | -__| || | | || _|| _|
  345. |_______|| __|_____|__|__||________||__| |____|
  346. |__| W I R E L E S S F R E E D O M
  347. -----------------------------------------------------
  348. OpenWrt oc200, r19375-77f278b3fbf
  349. -----------------------------------------------------
  350. root@oc200-dd7adf:/#

Edit this Snippet